ASTM D 4745 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Classification System and Basis for Specification for Filled Polytetrafluoroethlyene (PTFE) Molding and Extrusion Materials Using ASTM Methods
Hardcopy , PDF
06-06-2024
English
01-05-2019
Important note : Users cannot be edited or removed once added to your Multi user PDF.This specification covers polytetrafluoroethylene(PTFE) filled molding compounds made with virgin PTFE resins defined in a certain specification except Types I, IV, V, and VI.
| Committee |
D 20
|
| DocumentType |
Standard
|
| Pages |
6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This standard classification system and basis for specification covers polytetrafluoroethylene (PTFE) filled molding compounds made with virgin PTFE resins defined in Specification D4894, as Types II and III.
Note 1:This system can be used as a model for other PTFE compounds having particulate fillers that can survive the sintering temperatures of PTFE as can those listed in this standard. This system is restricted to virgin PTFE base resin for technical reasons. Recycled or reprocessed material cannot be processed successfully.
Note 2:The properties measured on commercially fabricated parts may differ from the listed values for samples prepared by the procedures given in this specification, depending on part geometry and processing parameters. Compounds used for ram extrusion are made from resins that comply with ASTM-D4745 Type II prior to their pre-sintering process. Property values measured on extruded products will vary from the listed values for Type II compounds which are prepared by the procedures given below which standardize mold diameter and sintering cycle. End users should assess these expected variations in ram extruded products to ensure their suitable use in their specific application.
1.2The values stated in SI units are to be regarded as standard.
1.3The following statement applies to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Note 5 for a specific warning statement.
Note 3:There is no known ISO equivalent to this standard.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1708 : 1996 | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
| ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
| ASTM D 1708 : 2006 : REV A | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 4894 : 1998 : REV A | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
| ASTM D 4894 : 2007 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1708 : 2002 | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
| ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
| ASTM D 1708 : 2006 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
| ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 4894 : 2004 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 1708 : 2013 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 4894 : 2015 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 1708 : 2010 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
| ASTM D 4894 : 2019 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 4894 : 2007 : R2012 | Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials |
| ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
| ASTM D 1708 : 2002 : REV A | Standard Test Method for Tensile Properties of Plastics By Use of Microtensile Specimens |
| ASTM D 1708 : 2018 | Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.