![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 4806 : 2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel
Hardcopy , PDF
19-09-2019
English
01-03-2019
This specification covers nominally anhydrous denatured fuel ethanol intended for blending with unleaded or leaded gasolines for use as a spark-ignition automotive engine fuel.
Committee |
D 02
|
DocumentType |
Standard
|
Pages |
9
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers nominally anhydrous denatured fuel ethanol intended to be blended with unleaded or leaded gasolines at 1 % to 15 % by volume for use as automotive spark-ignition engine fuel covered by Specification D4814 as well as other fuel applications or specifications involving ethanol. The significance of this specification is shown in Appendix X1.
1.2Jurisdictions may vary in their regulatory requirements for the allowable or prohibited types of denaturants, chemical composition of the denaturant or concentration of denaturant needed to denature the ethanol. The user is advised to check with the national and regional regulatory agencies where the ethanol is denatured and used.
1.2.1Specific regulatory requirements for denatured fuel ethanol and acceptable denaturants from various jurisdictions are given in Appendixes for information.
1.3The values stated in SI units are to be regarded as standard.
1.3.1Exception—Values given in parentheses are provided for information only. Non-SI units are shown in the Appendix if they are in a direct quotation from government regulations. In most cases, U.S. federal regulations specify non-SI units.
1.4The following safety hazards caveat pertains only to the method modification in 8.7 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7577 : 2012 : R2016 | Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends |
ASTM D 7717 : 2011 : R2017 | Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis |
ASTM D 7875 : 2014 | Standard Test Method for Determination of Butanol and Acetone Content of Butanol for Blending with Gasoline by Gas Chromatography |
ASTM D 7923 : 2019 | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM D 471 : 2016 : REV A | Standard Test Method for Rubber Property—Effect of Liquids |
ASTM D 5501 : 2012 : R2016 | Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography |
ASTM D 7563 : 2010 : R2016 | Standard Test Method for Evaluation of the Ability of Engine Oil to Emulsify Water and Simulated Ed85 Fuel |
ASTM D 4814 : 2019 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7757 : 2017 | Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 6423 : 2019 | Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends |
ASTM D 8076 : 2018 | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
ASTM D 1613 : 2017 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
ASTM D 7794 : 2018 : REV A | Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines |
ASTM D 3120 : 2008 : R2019 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 5797 : 2018 | Standard Specification for Methanol Fuel Blends (M51–M85) for Methanol-Capable Automotive Spark-Ignition Engines |
ASTM D 8011 : 2018 | Standard Specification for Natural Gasoline as a Blendstock in Ethanol Fuel Blends or as a Denaturant for Fuel Ethanol |
ASTM D 8235 : 2019 | Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5798 : 2019 : REV B | Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines |
ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2622 : 1992 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5580 : 2000 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <i>p/m</i>-Xylene, <i>o</i>-Xylene, C<sub>9</sub> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5453 : 2009 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5501 : 1994 : R1998 : EDT 1 | Standard Test Method for Determination of Ethanol Content of Denatured Fuel Ethanol by Gas Chromatography |
ASTM D 6423 : 1999 | Standard Test Method for Determination of pHe of Ethanol, Denatured Fuel Ethanol, and Fuel Ethanol (Ed75-Ed85) |
ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2004 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2013 | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 3120 : 1996 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 1298 : 2012 : REV A | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 7795 : 2012 | Standard Test Method for Acidity in Ethanol and Ethanol Blends by Titration |
ASTM D 4814 : 2016 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM E 1064 : 2012 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 3120 : 2008 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2008 : REV B | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 5501 : 2012 : EDT 1 | Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography |
ASTM D 1688 : 2002 | Standard Test Methods for Copper in Water |
ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 1688 : 2012 | Standard Test Methods for Copper in Water |
ASTM D 7576 : 2010 | Standard Test Method for Determination of Benzene and Total Aromatics in Denatured Fuel Ethanol by Gas Chromatography |
ASTM D 4814 : 2014 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2001 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 7923 : 2019 | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM D 4814 : 2004 : REV B : EDT 1 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 1298 : 2012 : REV B | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 5453 : 2004 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 4814 : 2015 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2000 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 7319 : 2011 : EDT 1 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2012 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4814 : 2011 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 1997 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4306 : 2015 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM E 1064 : 2000 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7347 : 2007 : EDT 1 | Standard Test Method for Determination of Olefin Content in Denatured Ethanol by Supercritical Fluid Chromatography |
ASTM E 1064 : 2005 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 2622 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4814 : 2018 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2010 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 7318 : 2011 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
ASTM D 7318 : 2007 | Standard Test Method for Total Inorganic Sulfate in Ethanol by Potentiometric Titration |
ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 1298 : 1999 : R2005 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2008 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM E 1064 : 2004 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 4814 : 2018 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 1298 : 2012 : REV B : R2017 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 1298 : 2012 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 5854 : 2019 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 4306 : 2001 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 1613 : 1996 : R1999 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 4814 : 1995 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2009 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2622 : 2008 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2016 : REV : EDT 0 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 2007 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 5501 : 2009 | Standard Test Method for Determination of Ethanol Content of Denatured Fuel Ethanol by Gas Chromatography |
ASTM D 1298 : 1999 : EDT 2 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 1613 : 2003 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 5580 : 2002 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <i>p/m</i>-Xylene, <i>o</i>-Xylene, C<sub>9</sub> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5453 : 2005 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 5854 : 1996 : R2005 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5580 : 2002 : R2007 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <span class="italic"> p/m</span>-Xylene, <span class="italic">o</span>-Xylene, C<sub>9</sub> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
ASTM D 4814 : 2012 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7318 : 2013 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
ASTM D 7328 : 2013 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 3120 : 2008 : R2019 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 7923 : 2017 : REV A : EDT 1 | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM D 6550 : 2005 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 4814 : 2010 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2003 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2001 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 1298 : 1999 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 5453 : 2006 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4814 : 2008 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7319 : 2007 | Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4814 : 2003 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4814 : 2004 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3120 : 2003 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4306 : 2012 : REV A | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 7923 : 2017 : REV A | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6423 : 2018 | Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends |
ASTM D 1688 : 1990 | Standard Test Methods for Copper in Water |
ASTM D 4814 : 2010 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2008 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2622 : 2003 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5501 : 2012 : R2016 | Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography |
ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4306 : 2012 : REV B | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 6550 : 2010 : R2015 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 7319 : 2017 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 7347 : 2015 | Standard Test Method for Determination of Olefin Content in Denatured Ethanol by Supercritical Fluid Chromatography (Withdrawn 2024) |
ASTM D 4814 : 2009 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7576 : 2016 | Standard Test Method for Determination of Benzene and Total Aromatics in Denatured Fuel Ethanol by Gas Chromatography (Withdrawn 2022) |
ASTM D 7039 : 2015 : REV A | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 7319 : 2009 | Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 3120 : 2003 : REV A | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 1298 : 1999 : EDT 1 | Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 7328 : 2016 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 7318 : 2019 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
ASTM D 4814 : 2011 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2004 | Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 1688 : 1995 | Standard Test Methods for Copper in Water |
ASTM D 5453 : 2003 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 4814 : 2008 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2002 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2011 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4814 : 2019 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 6550 : 2015 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM E 1064 : 2008 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 4814 : 2006 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2007 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2018 : REV D | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2015 | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2006 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2000 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 1613 : 2002 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 1613 : 2006 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 4814 : 1992 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 1613 : 2006 : R2012 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 4814 : 2014 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2015 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7319 : 2011 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 1688 : 2017 | Standard Test Methods for Copper in Water |
ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 7757 : 2012 | Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 7319 : 2012 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4814 : 2007 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2622 : 2010 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4814 : 2009 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2007 | Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 6550 : 2010 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 5580 : 2015 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <emph type="ital"> p/m</emph>-Xylene, <emph type="ital">o</emph>-Xylene, C<inf>9</inf> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
ASTM D 4814 : 2018 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2013 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 : REV D | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2017 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2000 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 3120 : 1996 : R2002 : EDT 1 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM E 1064 : 2004 : REV A | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 7328 : 2007 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 2622 : 2007 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2013 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7347 : 2007 | Standard Test Method for Determination of Olefin Content in Denatured Ethanol by Supercritical Fluid Chromatography |
ASTM D 3120 : 2006 : EDT 1 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4306 : 2013 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 2622 : 1994 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4814 : 2004 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3120 : 2006 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 5501 : 2012 | Standard Test Method for Determination of Ethanol and Methanol Content in Fuels Containing Greater than 20% Ethanol by Gas Chromatography |
ASTM D 7328 : 2011 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2622 : 2005 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 6550 : 2000 | Standard Test Method for Determination of Olefin Content of Gasolines by Supercritical-Fluid Chromatography |
ASTM D 7328 : 2017 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 6423 : 2014 | Standard Test Method for Determination of pHe of Denatured Fuel Ethanol and Ethanol Fuel Blends |
ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 7318 : 2018 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 7795 : 2015 | Standard Test Method for Acidity in Ethanol and Ethanol Blends by Titration |
ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 1298 : 1985 : R1990 : EDT 1 | Standard Practice for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 6423 : 2008 | Standard Test Method for Determination of pHe of Ethanol, Denatured Fuel Ethanol, and Fuel Ethanol (Ed75-Ed85) |
ASTM D 5854 : 2019 : REV A | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 4814 : 1993 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7757 : 2017 | Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 3120 : 2008 : R2014 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4814 : 2014 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4814 : 2018 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 1613 : 2017 | Standard Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products |
ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7923 : 2017 | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM D 5453 : 2003 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 7923 : 2016 | Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration |
ASTM E 1064 : 2016 | Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration |
ASTM D 4814 : 2007 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7328 : 2007 : EDT 1 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4814 : 2013 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2015 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 1688 : 2007 | Standard Test Methods for Copper in Water |
ASTM D 7319 : 2013 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5501 : 2004 | Standard Test Method for Determination of Ethanol Content of Denatured Fuel Ethanol by Gas Chromatography |
ASTM D 4306 : 2012 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5453 : 2008 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5453 : 2000 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 5580 : 2013 | Standard Test Method for Determination of Benzene, Toluene, Ethylbenzene, <emph type="ital"> p/m</emph>-Xylene, <emph type="ital">o</emph>-Xylene, C<inf>9</inf> and Heavier Aromatics, and Total Aromatics in Finished Gasoline by Gas Chromatography |
ASTM D 4306 : 2012 : REV C | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.