![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 5185 : 1997
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
11-11-2014
10-01-2002
Committee |
D 02
|
DocumentType |
Test Method
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1 This test method covers the determination of additive elements, wear metals, and contaminants in used lubricating oils by inductively coupled plasma atomic emission spectrometry (ICP-AES). The specific elements are listed in Table 1.
1.2 This test method covers the determination of selected elements, listed in Table 1, in re-refined and virgin base oils.
1.3 For analysis of any element using wavelengths below 190 nm, a vacuum or inert-gas optical path is required. The determination of sodium and potassium is not possible on some instruments having a limited spectral range.
1.4 This test method uses oil-soluble metals for calibration and does not purport to quantitatively determine insoluble particulates. Analytical results are particle size dependent, and low results are obtained for particles larger than a few micrometers.
1.5 Elements present at concentrations above the upper limit of the calibration curves can be determined with additional, appropriate dilutions and with no degradation of precision.
1.6 For elements other than calcium, sulfur, and zinc, the low limits listed in Table 2 and Table 3 were estimated to be ten times the repeatability standard deviation. For calcium, sulfur, and zinc, the low limits represent the lowest concentrations tested in the interlaboratory study.
1.7 The values stated in SI (metric) units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.1, 8.2, and 8.4
ASTM D 7414 : 2018 | Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7412 : 2018 | Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 6987/D6987M : 2013 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-10 Exhaust Gas Recirculation Diesel Engine (Withdrawn 2022) |
ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 8111 : 2019 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine |
ASTM D 4951 : 2014 | Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM D 7624 : 2018 | Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 8226 : 2019 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIF Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6984 : 2018 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine |
ASTM D 8184 : 2018 : EDT 1 | Standard Test Method for Ferrous Wear Debris Monitoring in In-Service Fluids Using a Particle Quantifier Instrument |
ASTM D 7320 : 2018 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 8114 : 2019 : REV A | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition |
ASTM D 7549 : 2019 | Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure |
ASTM D 4485 : 2018 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 7484 : 2019 | Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine |
ASTM D 7844 : 2018 | Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7589 : 2016 | Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine<rangeref></rangeref > |
ASTM D 6891 : 2015 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IVA Spark-Ignition Engine |
ASTM D 6443 : 2014 : R2019 : EDT 1 | Standard Test Method for Determination of Calcium, Chlorine, Copper, Magnesium, Phosphorus, Sulfur, and Zinc in Unused Lubricating Oils and Additives by Wavelength Dispersive X-ray Fluorescence Spectrometry (Mathematical Correction Procedure) |
ASTM D 7876 : 2013 : R2018 | Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants |
ASTM D 7155 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
ASTM D 8048 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine |
ASTM D 7151 : 2015 | Standard Test Method for Determination of Elements in Insulating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 7111 : 2016 | Standard Test Method for Determination of Trace Elements in Middle Distillate Fuels by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM D 7596 : 2014 | Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester |
ASTM D 6923 : 2018 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure |
ASTM D 8047 : 2018 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
ASTM D 8074 : 2018 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 8056 : 2018 | Standard Guide for Elemental Analysis of Crude Oil |
ASTM D 6681 : 2017 | Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1P Test Procedure |
ASTM D 7260 : 2019 | Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants |
ASTM D 7455 : 2019 | Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis |
ASTM E 2412 : 2010 : R2018 | Standard Practice for Condition Monitoring of In-Service Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 7578 : 2018 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
ASTM D 7583 : 2016 | Standard Test Method for John Deere Coolant Cavitation Test |
ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 7919 : 2014 : R2017 | Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes |
ASTM D 7040 : 2004 : R2015 | Standard Test Method for Determination of Low Levels of Phosphorus in ILSAC GF 4 and Similar Grade Engine Oils by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
ASTM D 7156 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in the T-11 Exhaust Gas Recirculation Diesel Engine |
ASTM D 8256 : 2019 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in the Sequence VH Spark-Ignition Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
ASTM D 4378 : 2013 | Standard Practice for In-Service Monitoring of Mineral Turbine Oils for Steam, Gas, and Combined Cycle Turbines |
ASTM D 5966 : 2013 | Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine (Withdrawn 2022) |
ASTM D 6594 : 2019 | Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 135 °C |
ASTM D 6074 : 2015 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 7415 : 2018 | Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry |
ASTM D 6224 : 2016 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
ASTM D 117 : 2018 | Standard Guide for Sampling, Test Methods, and Specifications for Electrical Insulating Liquids |
ASTM D 5968 : 2019 | Standard Test Method for Evaluation of Corrosiveness of Diesel Engine Oil at 121 °C |
ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
ASTM D 5708 : 2015 | Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM B 999 : 2015 | Standard Specification for Titanium and Titanium Alloys Plating, Electrodeposited Coatings of Titanium and Titanium Alloys on Conductive and Non-Conductive Substrate |
ASTM D 7303 : 2017 | Standard Test Method for Determination of Metals in Lubricating Greases by Inductively Coupled Plasma Atomic Emission Spectrometry |
ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5967 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
ASTM D 8120 : 2017 | Standard Test Method for Ferrous Debris Quantification |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.