ASTM D 5989 : 2018
Current
The latest, up-to-date edition.
Standard Specification for Extruded and Monomer Cast Shapes Made from Nylon (PA)
Hardcopy , PDF
English
01-08-2018
This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar, excluding pipe and fittings, manufactured from nylon or monomers.
Committee |
D 20
|
DocumentType |
Standard
|
Pages |
7
|
ProductNote |
This standard also refers to LP-410A
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and cast sheet, plate, rod and tubular bar, excluding pipe and fittings, manufactured from nylon or monomers.
1.2The properties included in this specification are those required for the compositions covered. Requirements necessary to identify particular characteristics important to specialized applications are described by using the classification system given in Section 4.
1.3This specification allows for the use of recycled plastics (as defined in Guide D7209).
1.4The values stated in English units are regarded as standard. The values in parentheses are for information only.
1.5The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:There is no known ISO equivalent to this standard.
Note 2:This specification is intended to replace Federal Standard LP-410A and PS 50.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 256 : 2010 : R2018 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 6779 : 2002 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 883 : 2023 | Standard Terminology Relating to Plastics |
ASTM D 6779 : 2005 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2020 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2007 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 883 : 2024 : REV A | Standard Terminology Relating to Plastics |
ASTM D 3892 : 2015 : R2020 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 6779 : 2003 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 883 : 2024 | Standard Terminology Relating to Plastics |
ASTM D 3892 : 1993 : R2003 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 256 : 2023 : EDT 1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 3892 : 2015 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 6779 : 2011 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 883 : 2022 | Standard Terminology Relating to Plastics |
ASTM D 883 : 2020 : REV B | Standard Terminology Relating to Plastics |
ASTM D 7209 : 2006 | Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
ASTM D 6779 : 2008 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 3892 : 1993 : R1998 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 6779 : 2004 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2012 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2006 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 256 : 2023 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics |
ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 6779 : 2004 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2023 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2012 : REV A | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2002 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 3892 : 1993 : R2009 | Standard Practice for Packaging/Packing of Plastics |
ASTM D 6779 : 2016 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2007 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2021 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2010 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2017 | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 6779 : 2008 : REV A | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
ASTM D 6779 : 2006 : EDT 1 | Standard Classification System for Polyamide Molding and Extrusion Materials (PA) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.