ASTM D 6130 : 2011 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy
Hardcopy , PDF
10-06-2024
English
01-03-2018
CONTAINED IN VOL. 15.05, 2018 Defines the determination of silicon in engine coolant by inductively coupled plasma-atomic emission spectroscopy (ICP-AES).
Committee |
D 15
|
DocumentType |
Test Method
|
Pages |
6
|
ProductNote |
Reconfirmed 2018
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the determination of silicon in engine coolant by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Silicon can be determined as low as the range of 5 ppm by this test method. Other elements also found in engine coolant can be determined by this method. This test method is applicable to the determination of dissolved or dispersed elements.
1.2This test method is applicable to both new and used engine coolant.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 5752 : 2010 : R2017 | Standard Specification for Supplemental Coolant Additives (SCAs) for Use in Precharging Coolants for Heavy-Duty Engines |
ASTM D 7715 : 2012 : R2016 : EDT 1 | Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines |
ASTM D 7517 : 2019 | Standard Specification for Fully-Formulated 1,3 Propanediol (PDO) Base Engine Coolant for Heavy-Duty Engines |
ASTM D 7518 : 2010 : R2015 : EDT 1 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 7713 : 2018 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
ASTM D 2847 : 2015 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
ASTM D 3306 : 2019 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 8039 : 2016 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
ASTM D 7388 : 2018 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
ASTM D 7260 : 2019 | Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants |
ASTM E 1177 : 2014 | Standard Specification for Engine Coolant Grade Glycol |
ASTM D 7640 : 2016 | Standard Specification for Engine Coolant Grade Glycerin |
ASTM D 4985 : 2010 : R2015 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
ASTM D 7714 : 2011 : R2016 : EDT 1 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 8566 : 2024 | Standard Specification for Glycol-Based Electric Vehicle Coolant with Low Electrical Conductivity |
ASTM D 2847 : 2022 | Standard Practice for Testing Engine Coolants in Car and Light Truck Service |
ASTM D 7640 : 2016 : R2021 | Standard Specification for Engine Coolant Grade Glycerin |
ASTM D 4985 : 2010 : R2023 | Standard Specification for Low Silicate Ethylene Glycol Base Engine Coolant for Heavy Duty Engines Requiring a Pre-Charge of Supplemental Coolant Additive (SCA) |
ASTM D 3306 : 2021 | Standard Specification for Glycol Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 7260 : 2020 | Standard Practice for Optimization, Calibration, and Validation of Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES) for Elemental Analysis of Petroleum Products and Lubricants |
ASTM D 7713 : 2018 : R2023 | Standard Specification for Aqueous Engine Coolant Grade Glycol (53 % by Volume Nominal) |
ASTM D 7518 : 2020 | Standard Specification for 1,3 Propanediol (PDO) Base Engine Coolant for Automobile and Light-Duty Service |
ASTM E 1177 : 2023 | Standard Specification for Engine Coolant Grade Glycol |
ASTM D 8565 : 2024 | Standard Specification for Glycol-Based Coolants for Fuel Cell Electric Vehicles |
ASTM D 7714 : 2011 : R2021 | Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service |
ASTM D 7388 : 2023 | Standard Specification for Engine Coolant Grade 1,3-Propanediol (PDO) |
ASTM D 8039 : 2016 : R2023 | Standard Specification for Heat Transfer Fluids (HTF) for Heating and Air Conditioning (HVAC) Systems |
ASTM D 8485 : 2023 | Standard Test Method for Corrosion Test for Electric Vehicle Coolants in Glassware |
ASTM D 7715 : 2012 : R2021 | Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines |
ASTM E 177 : 1990 : REV A : R1996 | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
ASTM D 1176 : 2014 : REDLINE | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM D 1176 : 1998 : R2008 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
ASTM D 1176 : 1998 : R2002 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
ASTM D 1176 : 1998 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1176 : 2014 : R2019 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM D 1176 : 2014 | Standard Practice for Sampling and Preparing Aqueous Solutions of Engine Coolants or Antirusts for Testing Purposes |
ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.