ASTM D 6984 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIF, Spark-Ignition Engine
Hardcopy , PDF
28-06-2022
English
19-04-2018
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
54
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers an engine test procedure for evaluating automotive engine oils for certain high-temperature performance characteristics, including oil thickening, varnish deposition, oil consumption, as well as engine wear. Such oils include both single viscosity grade and multiviscosity grade oils that are used in both spark-ignition, gasoline-fueled engines, as well as in diesel engines.
Note 1:Companion test methods used to evaluate engine oil performance for specification requirements are discussed in SAE J304.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1Exceptions—The values stated in inches for ring gap measurements are to be regarded as standard, and where there is no direct SI equivalent such as screw threads, National Pipe Threads/diameters, tubing size, or single source supply equipment specifications.
1.3This test method is arranged as follows:
Subject | Section |
Scope | 1 |
Referenced Documents | 2 |
Terminology | 3 |
Summary of Test Method | 4 |
Significance and Use | 5 |
Apparatus | 6 |
Laboratory | 6.1 |
Drawings | 6.2 |
Specified Equipment | 6.3 |
Test Engine | 6.4 |
Engine Parts | 6.4.1 |
Engine Speed and Torque Control | 6.5 |
Sequence IIIF Fluid Conditioning Module | 6.6 |
Engine Cooling System | 6.6.1 |
Flushing Tank | 6.7 |
Coolant Mixing Tank | 6.8 |
Condenser Cooling Systems | 6.9 |
Engine Oil-Cooling System | 6.10 |
Fuel System | 6.11 |
Induction Air Supply Humidity, Temperature, and Pressure | 6.12 |
Temperature Measurement | 6.13 |
Thermocouple Location | 6.13.1 |
Air-to-Fuel Ratio Determination | 6.14 |
Injector Flow Testing | 6.14.1 |
Exhaust and Exhaust Back Pressure Systems | 6.15 |
Blowby Flow Rate Measurement | 6.16 |
Pressure Measurement and Pressure Sensor Location | 6.17 |
Reagents and Materials | 7 |
Test Fuel | 7.1 |
Engine and Condenser Coolant | 7.2 |
Coolant Additive | 7.3 |
Coolant Preparation | 7.4 |
Pre-Test Cleaning Materials | 7.5 |
Sealing and Anti-seize Compounds | 7.6 |
Test Oil Sample Requirements | 8 |
Preparation of Apparatus | 9 |
Condenser Cleaning | 9.1 |
Intake Manifold Cleaning | 9.3 |
Cleaning of Engine Parts (other than the block and heads) | 9.4 |
Engine Block Cleaning | 9.5 |
Cylinder Head Cleaning | 9.6 |
Engine Build-up Procedure | 9.7 |
General Information | 9.7.1 |
Special Parts | 9.7.2 |
Hardware Information | 9.7.3 |
Fastener Torque Specifications and Torquing Procedures | 9.7.4 |
Parts Replacement | 9.8 |
Engine Block Preparation | 9.9 |
Piston Fitting and Numbering | 9.10 |
Piston Ring Fitting | 9.10.1 |
Pre-Test Camshaft and Lifter Measurements | 9.11 |
Camshaft Bearing Installation | 9.12 |
Camshaft Installation | 9.13 |
Main Bearings | 9.14 |
Crankshaft Installation | 9.14.1 |
Main Bearing Cap Installation | 9.14.2 |
Crankshaft Sprocket | 9.15 |
Camshaft Sprocket and Timing Chain | 9.16 |
Crankshaft End Play | 9.17 |
Piston Pin Installation | 9.18 |
Piston Installation | 9.18.1 |
Harmonic Balancer | 9.19 |
Connecting Rod Bearings | 9.20 |
Engine Front Cover | 9.21 |
Coolant Inlet Adapter | 9.22 |
Oil Dipstick Hole | 9.23 |
Oil Pan | 9.24 |
Cylinder Head Assembly | 9.25 |
Adjustment of Valve Spring Forces | 9.26 |
Cylinder Head Installation | 9.27 |
Hydraulic Valve Lifters | 9.28 |
Pushrods | 9.29 |
Valve Train Loading | 9.30 |
Intake Manifold | 9.31 |
Rocker Covers | 9.32 |
Water Inlet Adapter | 9.33 |
Condenser | 9.34 |
Coolant Outlet Adapter | 9.35 |
External Oil Cooling System | 9.36 |
Oil Sample Valve | 9.37 |
Ignition System | 9.38 |
Throttle Body | 9.39 |
Accessory Drive Units | 9.40 |
Exhaust Manifolds, Water-Cooled | 9.41 |
Engine Flywheel | 9.42 |
Pressure Checking of Engine Coolant System | 9.43 |
Lifting of Assembled Engines | 9.44 |
Mounting the Engine on the Test Stand | 9.45 |
External Cooling System Cleaning | 9.46 |
Engine Coolant Jacket Cleaning (Flushing) | 9.47 |
Coolant Charging | 9.48 |
Test Oil Charging | 9.49 |
Engine Oil Pump Priming | 9.50 |
Calibration | 10 |
Laboratory and Engine Test Stand Calibration | 10.1 |
Testing of Reference Oils | 10.2 |
Reference Oil Test Frequency | 10.3 |
Evaluation of Reference Oil Test Results | 10.4 |
Status of Non-Reference Oil Tests Relative to Reference | 10.5 |
Status of Test Stands Used for Non-Standard Tests | 10.6 |
Data Acquisition and Control | 10.7 |
Sample Rate | 10.7.1 |
Measurement Accuracy | 10.7.2 |
Temperature | 10.7.3 |
Pressure | 10.7.4 |
Flow | 10.7.5 |
Speed | 10.7.6 |
Mass | 10.7.7 |
Measurement Resolution | 10.7.8 |
System Time Response | 10.7.9 |
Quality Index | 10.7.10 |
Engine Operating Procedure | 11 |
Dipstick and Hole Plug | 11.1 |
Dipstick Hole O-ring | 11.2 |
Engine Start-up and Shutdown Procedures | 11.3 |
Start-up | 11.4 |
Scheduled Shutdown | 11.5 |
Non-Scheduled Shutdowns | 11.6 |
Oil Sampling | 11.7 |
Oil Leveling | 11.8 |
Air-to-Fuel-Ratio Measurement and Control | 11.9 |
Air-to-Fuel Ratio Verification | 11.10 |
Blowby Flow Rate Measurement | 11.11 |
NOx Determinations | 11.12 |
Data Recording | 11.13 |
Initial Run (10 min) | 11.14 |
Engine Oil Quality Testing (80 h) | 11.15 |
Test Termination | 11.16 |
Determination of Test Results | 12 |
Engine Disassembly | 12.2 |
Preparation of Parts for Rating of Sticking, Deposits, | 12.3 |
Piston Deposit Ratings | 12.4 |
Post-Test Camshaft and Lifter Wear Measurements | 12.5 |
End-of Test Used Oil Sample Testing | 12.6 |
Viscosity Test | 12.7 |
Testing Oil Samples for Wear Metals | 12.8 |
Blowby Flow Rate Measurements | 12.9 |
Oil Consumption Computation | 12.10 |
Photographs of Test Parts | 12.11 |
Retention of Representative Test Parts | 12.12 |
Severity Adjustments | 12.13 |
Determination of Operational Validity | 12.14 |
Report | 13 |
Report Forms | 13.1 |
Precision of Reported Units | 13.4 |
Deviations from Test Operational Limits | 13.3 |
Precision and Bias | 14 |
Keywords | 15 |
Annexes | |
ASTM Test Monitoring Center – Organization | Annex A1 |
ASTM Test Monitoring Center – Calibration Procedures | Annex A2 |
ASTM Test Monitoring Center – Maintenance Activities | Annex A3 |
ASTM Test Monitoring Center – Related Information | Annex A4 |
Sequence IIIF Test Parts Replacement Guidelines | Annex A5 |
Sequence IIIF Determination Volume of Engine Oil in Pan | Annex A6 |
Sequence IIIF Test Fuel Analysis | Annex A7 |
Sequence IIIF Test Report Forms and Data Dictionary | Annex A8 |
Sequence IIIF Test Air-to-Fuel Ratio Control Flow Chart | Annex A9 |
Sequence IIIF Test Set Points and Control States | Annex A10 |
Sequence IIIF Quality Index Upper and Lower Values | Annex A11 |
Sequence IIIF Engine Oil Level Worksheet | Annex A12 |
Engine Build Worksheets | Annex A13 |
Blowby Flow Rate Determination | Annex A14 |
Safety Precautions | Annex A15 |
Sequence IIIF Blueprint Listing | Annex A16 |
Fluid Conditioning Module Components | Annex A17 |
Engine Oil Cooling System Configuration | Annex A18 |
Guidelines For Hardware Subject To First-In/First-Out Criteria | Annex A19 |
Appendixes | |
Sequence IIIFHD Test Procedure | Appendix X1 |
Sequence IIIFVIS Test Procedure | Appendix X2 |
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 7320 : 2018 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 5704 : 2017 | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 8074 : 2018 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 4485 : 2020 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 8291 : 2021 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
ASTM D 5704 : 2022 | Standard Test Method for Evaluation of the Thermal and Oxidative Stability of Lubricating Oils Used for Manual Transmissions and Final Drive Axles |
ASTM D 8074 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine |
ASTM D 2699 : 2016 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 3338 : 1992 | Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels |
ASTM D 1319 : 1989 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Absorption |
ASTM D 6750 : 2017 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM G 40 : 2021 | Standard Terminology Relating to Wear and Erosion |
ASTM D 5185 : 1997 | Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) |
ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM D 5191 : 2018 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4485 : 2015 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 7422 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7422 : 2016 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6593 : 2015 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 6750 : 2016 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 4815 : 2015 : REV B : R2019 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
ASTM D 2699 : 1992 | Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method |
ASTM D 240 : 1992 : R1997 : EDT 2 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter |
ASTM D 6750 : 2019 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 7422 : 2015 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4485 : 2018 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 2700 : 1992 | Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method |
ASTM D 6557 : 2000 | Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils |
ASTM D 4815 : 2022 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM D 235 : 2022 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) |
ASTM D 6593 : 2015 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 6750 : 2018 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM E 1119 : 1997 | Standard Specification for Industrial Grade Ethylene Glycol |
ASTM D 2700 : 2022 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7422 : 2010 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7422 : 2008 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 2700 : 2017 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7422 : 2017 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7320 : 2015 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 445 : 1988 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) |
ASTM D 5452 : 2000 | Standard Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration |
ASTM D 7320 : 2016 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 7320 : 2015 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 4485 : 2000 | Standard Specification for Performance of Engine Oils |
ASTM D 3343 : 2005 : R2015 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
ASTM D 7422 : 2022 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 6750 : 2015 : REV A | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 4485 : 2015 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 3343 : 1990 | Standard Test Method for Estimation of Hydrogen Content of Aviation Fuels |
ASTM D 2699 : 2019 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 6593 : 2000 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5191 : 1999 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 7422 : 2015 : REV A | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 7320 : 2006 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 7320 : 2017 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM G 40 : 2021 : REV A | Standard Terminology Relating to Wear and Erosion |
ASTM D 7320 : 2008 | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
ASTM E 608/E608M : 2013 : R2019 | Standard Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples |
ASTM D 7422 : 2016 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 2700 : 2021 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4815 : 1999 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 2700 : 2019 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 2699 : 2015 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 235 : 2002 : R2012 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021) |
ASTM D 4485 : 2018 : REV A | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 381 : 2019 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
ASTM D 381 : 2022 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
ASTM D 6593 : 2001 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 5293 : 1999 : REV A : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils Between -5 and -35<sup>o</sup>C Using the Cold-Cranking Simulator |
ASTM D 445 : 2001 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity) |
ASTM D 6593 : 2016 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 2699 : 2021 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
ASTM D 5293 : 2017 : EDT 1 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
ASTM D 4485 : 2014 | Standard Specification for Performance of Active API Service Category Engine Oils |
ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 6557 : 2018 | Standard Test Method for Evaluation of Rust Preventive Characteristics of Automotive Engine Oils |
ASTM D 6750 : 2015 | Standard Test Methods for Evaluation of Engine Oils in a High-Speed, Single-Cylinder Diesel Engine—1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5862 : 1999 : REV A | Standard Test Method for Evaluation of Engine Oils in Two-Stroke Cycle Turbo-Supercharged 6V92TA Diesel Engine |
ASTM D 7320 : 2017 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 6593 : 2016 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
ASTM D 4052 : 2022 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM E 1119 : 2009 : R2015 : EDT 1 | Standard Specification for Industrial Grade Ethylene Glycol |
ASTM D 7422 : 2017 | Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine |
ASTM D 3237 : 1997 | Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy |
ASTM D 3231 : 1989 | Standard Test Method for Phosphorus in Gasoline |
ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
ASTM G 40 : 2017 | Standard Terminology Relating to Wear and Erosion |
ASTM D 7320 : 2016 : REV A | Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIG, Spark-Ignition Engine |
ASTM D 6750 : 2002 | Standard Test Methods for Evaluation of Engine Oils in A High-Speed, Single-Cylinder Diesel Engine -1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur) |
ASTM D 5293 : 2017 | Standard Test Method for Apparent Viscosity of Engine Oils and Base Stocks Between –10 °C and –35 °C Using Cold-Cranking Simulator |
ASTM E 1119 : 2009 : R2015 | Standard Specification for Industrial Grade Ethylene Glycol |
ASTM D 1319 : 2002 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.