![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 7042 : 2016 : EDT 3
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
Hardcopy , PDF
27-08-2020
English
15-05-2016
This test method covers and specifies a procedure for the concurrent measurement of both the dynamic viscosity, η, and the density, ρ, of liquid petroleum products and crude oils, both transparent and opaque
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
13
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers and specifies a procedure for the concurrent measurement of both the dynamic viscosity, η, and the density, ρ, of liquid petroleum products and crude oils, both transparent and opaque. The kinematic viscosity, ν, can be obtained by dividing the dynamic viscosity, η, by the density, ρ, obtained at the same test temperature.
1.2The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rate are proportional (Newtonian flow behavior).
1.3The precision has only been determined for those materials, viscosity ranges, density ranges, and temperatures as indicated in Section 15 on Precision and Bias. The test method can be applied to a wider range of materials, viscosity, density, and temperature. For materials not listed in Section 15 on Precision and Bias, the precision and bias may not be applicable.
1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
ASTM D 7973 : 2019 | Standard Guide for Monitoring Failure Mode Progression in Plain Bearings |
ASTM D 7752 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids |
ASTM D 5372 : 2017 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 7863 : 2017 | Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids |
ASTM D 3699 : 2019 | Standard Specification for Kerosine |
ASTM D 396 : 2019 : REV A | Standard Specification for Fuel Oils |
ASTM D 1655 : 2019 : REV A | Standard Specification for Aviation Turbine Fuels |
ASTM F 3208 : 2019 | Standard Guide for Selecting Test Soils for Validation of Cleaning Methods for Reusable Medical Devices |
ASTM D 3699 : 2018 : REV A | Standard Specification for Kerosine |
ASTM D 4174 : 2017 | Standard Practice for Cleaning, Flushing, and Purification of Petroleum Fluid Hydraulic Systems |
ASTM D 2270 : 2010 : R2016 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 6823 : 2008 : R2013 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 7720 : 2011 : R2017 | Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination |
ASTM D 6074 : 2015 | Standard Guide for Characterizing Hydrocarbon Lubricant Base Oils |
ASTM D 341 : 2017 | Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products |
ASTM D 1655 : 2019 | Standard Specification for Aviation Turbine Fuels |
ASTM D 8181 : 2019 | Standard Specification for Microemulsion Blendstock for Preparing Microemulsion Test Fuel Oils |
ASTM D 7826 : 2019 | Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives |
ASTM D 7665 : 2017 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 7666 : 2012 | Standard Specification for Triglyceride Burner Fuel |
ASTM D 8185 : 2018 | Standard Guide for In-Service Lubricant Viscosity Measurement |
ASTM D 8128 : 2017 | Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings |
ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 4054 : 2019 | Standard Practice for Evaluation of New Aviation Turbine Fuels and Fuel Additives |
ASTM F 3208 : 2018 | Standard Guide for Selecting Test Soils for Validation of Cleaning Methods for Reusable Medical Devices |
ASTM D 8147 : 2017 | Standard Specification for Special-Purpose Test Fuels for Aviation Compression-Ignition Engines |
ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6710 : 2017 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM F 3337 : 2019 | Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil |
ASTM D 7566 : 2019 | Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons |
ASTM D 2161 : 2019 | Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity |
ASTM D 7152 : 2011 : R2016 | Standard Practice for Calculating Viscosity of a Blend of Petroleum Products |
ASTM D 6448 : 2016 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 7223 : 2017 | Standard Specification for Aviation Certification Turbine Fuel |
ASTM D 7155 : 2018 | Standard Practice for Evaluating Compatibility of Mixtures of Turbine Lubricating Oils |
ASTM D 2502 : 2014 : R2019 | Standard Test Method for Estimation of Mean Relative Molecular Mass of Petroleum Oils from Viscosity Measurements |
ASTM D 2501 : 2014 : R2019 | Standard Test Method for Calculation of Viscosity-Gravity Constant (VGC) of Petroleum Oils |
ASTM D 396 : 2019 | Standard Specification for Fuel Oils |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6300 : 2013 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6299 : 2010 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6300 : 2014 : REV A : EDT 1 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7467 : 2018 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6299 : 2013 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6708 : 2018 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6708 : 2015 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6708 : 2013 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6299 : 2017 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6299 : 2017 : REV B | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 7467 : 2009 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2017 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6299 : 2009 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6708 : 2007 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 2270 : 2010 | Standard Practice for Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C |
ASTM D 6751 : 2006 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6300 : 2017 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6751 : 2007 : REV B | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6751 : 2006 : EDT 1 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6299 : 2013 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6751 : 2018 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6751 : 2009 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6751 : 2007 : REV B : EDT 1 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6708 : 2016 : REV B | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 2162 : 1999 | Standard Test Method for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 6299 : 2010 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 7467 : 2010 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2016 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7467 : 2008 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6751 : 2007 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6708 : 2006 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 2162 : 2017 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6300 : 2004 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 7467 : 2017 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6617 : 2013 | Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material |
ASTM D 6617 : 2005 | Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material |
ASTM D 6751 : 2012 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7467 : 2015 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2019 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6751 : 2014 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7467 : 2015 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6708 : 2004 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6300 : 2019 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6708 : 2019 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6708 : 2016 : REV A | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6708 : 2008 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6299 : 2000 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 2270 : 2004 | Standard Practice for Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C |
ASTM D 6299 : 2010 : EDT 2 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6751 : 2011 : REV B | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6299 : 2016 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6751 : 2015 : REV B | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7467 : 2015 : EDT 1 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 7467 : 2015 : REV C | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6751 : 2015 : REV C | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 2162 : 1999 : R2004 | Standard Test Method for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6751 : 2015 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6299 : 2000 : REV A | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6300 : 2006 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2270 : 2010 : EDT 1 | Standard Practice for Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C |
ASTM D 6617 : 2008 | Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material |
ASTM D 7467 : 2014 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2014 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2162 : 1999 : EDT 1 | Standard Test Method for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 6751 : 2002 | Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels |
ASTM D 6708 : 2001 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6751 : 2003 : REV A | Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels |
ASTM D 6300 : 2015 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2162 : 2006 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 6300 : 1999 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2270 : 2010 : R2016 | Standard Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 °C and 100 °C |
ASTM D 6708 : 2001 : EDT 1 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6299 : 2008 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6751 : 2003 | Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels |
ASTM D 6708 : 2005 | Standard Practice for Statistical Assessment and Improvement of the Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6751 : 2008 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6751 : 2019 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6708 : 2013 : EDT 1 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 6300 : 2013 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6299 : 2002 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6708 : 2016 | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
ASTM D 2162 : 2013 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 7467 : 2018 : REV B | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6751 : 2015 : REV C : EDT 1 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7467 : 2009 : REV A | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2008 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6300 : 2003 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 2162 : 2014 | Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards |
ASTM D 6300 : 2007 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6751 : 2007 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 2270 : 1993 : R1998 | Standard Practice for Calculating Viscosity Index From Kinematic Viscosity at 40 and 100°C |
ASTM D 7467 : 2015 : REV C : EDT 1 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6300 : 2002 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6708 : 2019 : REV A | Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material |
ASTM D 7467 : 2019 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6751 : 2011 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 7467 : 2015 : REV B | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6751 : 2011 : REV A | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6300 : 2016 : REV A | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6751 : 2015 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6299 : 2007 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 7467 : 2013 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6299 : 2007 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 7467 : 2018 | Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20) |
ASTM D 6299 : 2017 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6751 : 2009 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 6300 : 2014 | Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants |
ASTM D 6751 : 2010 | Standard Specification for Biodiesel Fuel Blend Stock (B100) for Middle Distillate Fuels |
ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
ASTM D 6751 : 2002 : REV A | Standard Specification for Biodiesel Fuel (B100) Blend Stock for Distillate Fuels |
ASTM D 6617 : 2000 | Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material |
ASTM D 6299 : 2002 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
ASTM D 6617 : 2017 | Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.