![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 8076 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines
Hardcopy , PDF
03-01-2020
English
01-04-2018
Committee |
D 02
|
DocumentType |
Standard
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the requirements of a high octane number test fuel suitable for spark-ignition engines to be utilized in ground vehicles that will require 100 research octane number (RON) minimum rated fuel.
1.1.1The fuels described by this specification are intended for developing technologies that lead to reduced vehicle energy consumption, such as higher compression ratio, higher power density, increased turbocharger boost pressure, smaller swept displacement volume, and operation at lower engine speeds.
1.1.2The fuels described in this test fuel specification may not meet all of the performance or regulatory requirements for use in vehicles using commercial gasoline.
1.2The fuels covered in this specification may contain oxygenates, such as alcohols and ethers, up to 50 % by volume. This specification covers fuels that may contain both fossil and bio-derived components.
1.3This specification provides a description of high RON test fuel for automotive spark-ignition engines that are not currently in the marketplace but are being developed and require a defined standard test fuel. The high RON fuel could become available in the marketplace if/when such engines are introduced in commerce. The specification is under continuous review, which can result in revisions based on changes in fuel, automotive requirements, or test methods, or a combination thereof. All users of this specification, therefore, should refer to the latest edition.
Note 1:If there is any doubt as to the latest edition of Specification D8076, contact ASTM International Headquarters.
1.4The values stated in SI units are the standard.
1.4.1Exception—Non-SI values are provided for information only. U.S. federal regulations frequently specify non-SI units.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4175 : 2014 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2622 : 1992 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2009 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2699 : 2016 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 2011 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2008 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5453 : 2009 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4806 : 2002 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 2622 : 1987 : EDT 1 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4175 : 2005 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4806 : 2016 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2004 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 1999 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7039 : 2013 | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 3120 : 1996 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 5983 : 2013 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2005 : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7667 : 2010 : EDT 1 | Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method |
ASTM D 2700 : 2009 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2018 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7220 : 2012 | Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4814 : 2016 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2004 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 1152 : 2006 : R2012 | Standard Specification for Methanol (Methyl Alcohol) (Withdrawn 2021) |
ASTM D 2700 : 2011 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 3120 : 2008 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2008 : REV B | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 2699 : 2007 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5453 : 2000 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 2700 : 2007 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4176 : 1993 : R1997 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 2699 : 2013 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2015 : REV C | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7862 : 2015 : REV A | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 1266 : 1998 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
ASTM D 7220 : 2012 : R2017 | Standard Test Method for Sulfur in Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4815 : 2015 : REV B | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM D 5191 : 2018 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 4814 : 2014 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 6920 : 2013 | Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection (Withdrawn 2018) |
ASTM D 7862 : 2019 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2017 : REV A : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 2699 : 2017 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4814 : 2001 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2007 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5482 : 2007 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method<span class='unicode'>—</span>Atmospheric) |
ASTM D 4814 : 2004 : REV B : EDT 1 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3831 : 2012 | Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy |
ASTM D 5453 : 2004 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 6378 : 2018 : REV A | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 2700 : 2014 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4814 : 2015 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2000 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2009 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 2700 : 2007 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7319 : 2011 : EDT 1 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4175 : 2008 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2012 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4953 : 2015 | Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method) |
ASTM D 5599 : 2000 : R2010 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 4814 : 2011 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 1997 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4175 : 2017 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4306 : 2015 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4175 : 2009 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 6378 : 2008 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 5842 : 2014 | Standard Practice for Sampling and Handling of Fuels for Volatility Measurement |
ASTM D 1266 : 2013 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
ASTM D 5191 : 2006 : EDT 1 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4806 : 2015 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 1152 : 2006 | Standard Specification for Methanol (Methyl Alcohol) |
ASTM D 2622 : 1998 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4806 : 2006 : REV B | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2018 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2013 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 1992 | Standard Test Method for Knock Characteristics of Motor Fuels by the Research Method |
ASTM D 5854 : 1996 : R2010 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 3237 : 2006 : EDT 1 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
ASTM D 2700 : 2010 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2003 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 1992 | Standard Test Method for Knock Characteristics of Motor and Aviation Fuels by the Motor Method |
ASTM D 6920 : 2003 | Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection |
ASTM D 4175 : 2009 : REV A : EDT 4 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 7618 : 2010 | Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel |
ASTM D 5842 : 2004 | Standard Practice for Sampling and Handling of Fuels for Volatility Measurement |
ASTM D 4175 : 2009 : REV A : EDT 3 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2699 : 2001 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4806 : 2006 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5453 : 2008 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4814 : 2018 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2003 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5854 : 2019 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 5599 : 2018 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 1266 : 1987 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
ASTM D 7862 : 2013 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 2001 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4814 : 1995 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2009 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2622 : 2008 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5845 : 2001 : R2016 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <emph type="ital">tert</emph>-Butanol in Gasoline by Infrared Spectroscopy |
ASTM D 5059 : 1998 | Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy |
ASTM D 4175 : 2018 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2016 : REV : EDT 0 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 2007 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4806 : 2006 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2012 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4806 : 2001 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2009 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5191 : 2001 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 2700 : 2012 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 1999 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4806 : 2014 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2005 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 2700 : 2017 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2005 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 5842 : 1995 : R2000 | Standard Practice for Sampling and Handling of Fuels for Volatility Measurement |
ASTM D 4175 : 2001 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2005 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5845 : 1995 : R2000 : EDT 1 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert-</i>Butanol in Gasoline by Infrared Spectroscopy |
ASTM D 2700 : 2016 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4814 : 2012 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2004 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2001 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5191 : 2010 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 7862 : 2015 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2013 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 7328 : 2013 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 2699 : 2012 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7667 : 2010 | Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel<char: emdash>Thin Silver Strip Method |
ASTM D 3120 : 2008 : R2019 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 6378 : 2010 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 4814 : 2010 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2003 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 3237 : 2002 | Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy |
ASTM D 4814 : 2001 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2006 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4806 : 2001 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2016 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5453 : 2006 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4814 : 2008 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2003 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4953 : 1999 : REV A | Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method) |
ASTM D 4176 : 2004 : R2009 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 7319 : 2007 | Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4814 : 2003 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5059 : 2014 | Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy |
ASTM D 4806 : 2008 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4806 : 2018 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 7671 : 2010 : EDT 1 | Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method |
ASTM D 2699 : 2011 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2015 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4175 : 2002 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4806 : 2017 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 5983 : 1997 : R2002 | Standard Specification for Methyl <I>Tertiary</I>-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2010 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2004 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3120 : 2003 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 5191 : 2012 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4306 : 2012 : REV A | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 4806 : 2011 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2012 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4953 : 2006 : R2012 | Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method) |
ASTM D 2699 : 2008 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2013 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5845 : 2001 : R2006 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert</i>-Butanol in Gasoline by Infrared Spectroscopy |
ASTM D 4814 : 2010 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2008 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 5845 : 2001 : R2011 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <span class="italic">tert</span>-Butanol in Gasoline by Infrared Spectroscopy |
ASTM D 4815 : 1999 : EDT 1 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 2700 : 2018 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5191 : 2003 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 2622 : 2003 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 3831 : 2001 | Standard Test Method for Manganese In Gasoline By Atomic Absorption Spectroscopy |
ASTM D 4806 : 2016 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2016 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 5059 : 2014 : R2019 | Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy |
ASTM D 4175 : 2009 : REV A : EDT 5 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 6920 : 2007 | Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection |
ASTM D 4175 : 2016 : REV C | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4306 : 2012 : REV B | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 2700 : 2016 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2015 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2699 : 2003 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2003 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5191 : 1999 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 7319 : 2017 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4814 : 2009 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2015 : REV A | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 7618 : 2013 | Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel |
ASTM D 5983 : 2006 : R2011 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2018 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7319 : 2009 | Standard Test Method for Determination of Total and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 2700 : 2011 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2015 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 3120 : 2003 : REV A | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 7328 : 2016 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4814 : 2011 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2004 | Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4806 : 2007 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4815 : 2009 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4806 : 2019 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2004 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2010 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 6378 : 1999 : EDT 1 | Standard Test Method for Determination of Vapor Pressure (VP<sub>x</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 5453 : 2003 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 7667 : 2010 : EDT 2 | Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method |
ASTM D 4814 : 2008 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2009 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5983 : 2006 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2011 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4815 : 2015 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4814 : 2002 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4815 : 2004 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4175 : 2016 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2011 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4815 : 1999 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, <I>tertiary</I>-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 2700 : 2002 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5842 : 2004 : R2009 | Standard Practice for Sampling and Handling of Fuels for Volatility Measurement |
ASTM D 2700 : 2007 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4814 : 2019 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2013 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4175 : 2002 : REV A : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 6378 : 2006 | Standard Test Method for Determination of Vapor Pressure (VP<sub>X</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 4175 : 2008 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4806 : 2019 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 6378 : 2003 | Standard Test Method for Determination of Vapor Pressure (VP<sub>x</sub>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 4814 : 2006 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2007 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2002 : REV A | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2007 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5191 : 2018 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 3831 : 2001 : R2006 | Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy |
ASTM D 5191 : 2010 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4176 : 2004 : R2014 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 5059 : 2007 | Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy |
ASTM D 4175 : 2000 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4814 : 2018 : REV D | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2016 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5599 : 2015 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 7039 : 2015 | Standard Test Method for Sulfur in Gasoline, Diesel Fuel, Jet Fuel, Kerosine, Biodiesel, Biodiesel Blends, and Gasoline-Ethanol Blends by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2016 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 3237 : 2006 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
ASTM D 4814 : 2006 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5599 : 2017 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 4806 : 2018 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2000 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 2700 : 2004 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4814 : 1992 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4815 : 2013 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4814 : 2014 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2015 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 7319 : 2011 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 7319 : 2012 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 5191 : 2002 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 2699 : 2004 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 2015 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 2013 : REV B | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2013 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5482 : 1999 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method-Atmospheric) |
ASTM D 5482 : 2001 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method-Atmospheric) |
ASTM D 4814 : 2007 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2622 : 2010 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5191 : 2019 | Standard Test Method for Vapor Pressure of Petroleum Products and Liquid Fuels (Mini Method) |
ASTM D 4814 : 2009 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5599 : 2000 : R2005 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 4806 : 2008 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 7039 : 2007 | Standard Test Method for Sulfur in Gasoline and Diesel Fuel by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2699 : 2001 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 2006 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4815 : 2003 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<sub>1</sub> to C<sub>4</sub> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4814 : 2018 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2013 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4806 : 2006 : REV C | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5482 : 2007 : R2013 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method—Atmospheric) |
ASTM D 6378 : 2010 : R2016 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 4814 : 2016 : REV D | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2017 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 4814 : 2000 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2019 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 3120 : 1996 : R2002 : EDT 1 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 7328 : 2007 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 2699 : 2015 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2622 : 2007 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 5059 : 2013 | Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy |
ASTM D 7220 : 2006 | Standard Test Method for Sulfur in Automotive Fuels by Polarization X-ray Fluorescence Spectrometry |
ASTM D 4175 : 2017 : REV A | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4814 : 2013 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3120 : 2006 : EDT 1 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 7862 : 2018 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4306 : 2013 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 2622 : 1994 | Standard Test Method for Sulfur in Petroleum Products by X-Ray Spectrometry |
ASTM D 4814 : 2004 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3120 : 2006 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 2699 : 2002 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7328 : 2011 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4175 : 2009 : REV A : EDT 2 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 2622 : 2005 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 2700 : 2017 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 7667 : 2010 : R2015 | Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method |
ASTM D 7328 : 2017 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 7671 : 2010 | Standard Test Method for Corrosiveness to Silver by Automotive Spark<span class='unicode'>–</span>Ignition Engine Fuel<span class='unicode'>–</span>Silver Strip Method |
ASTM D 4806 : 2009 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2003 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5191 : 2004 : REV A | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4806 : 2012 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 3237 : 2017 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 4175 : 2018 : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4175 : 2016 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 7671 : 2010 : R2015 | Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method |
ASTM D 3831 : 1998 | Standard Test Method for Manganese In Gasoline By Atomic Absorption Spectroscopy |
ASTM D 2699 : 2009 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5599 : 2000 | Standard Test Method for Determination of Oxygenates in Gasoline by Gas Chromatography and Oxygen Selective Flame Ionization Detection |
ASTM D 2699 : 2004 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2699 : 2006 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5854 : 2019 : REV A | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 4814 : 1993 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 3237 : 1997 | Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy |
ASTM D 5983 : 2017 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 5842 : 2017 | Standard Practice for Sampling and Handling of Fuels for Volatility Measurement |
ASTM D 4806 : 2010 : REV B | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5191 : 2007 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 2700 : 2004 : EDT 1 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 1152 : 1997 | Standard Specification for Methanol (Methyl Alcohol) |
ASTM D 3120 : 2008 : R2014 | Standard Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative Microcoulometry |
ASTM D 2700 : 2001 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 6378 : 2007 : EDT 1 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 5191 : 2015 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4814 : 2014 | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 6378 : 2018 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 2699 : 2018 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4175 : 2017 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 4815 : 2015 : REV A | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, tertiary-Amyl Alcohol and C<inf>1</inf> to C<inf>4</inf> Alcohols in Gasoline by Gas Chromatography |
ASTM D 4806 : 1999 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 7618 : 2013 : R2017 | Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel |
ASTM D 3831 : 2012 : R2017 | Standard Test Method for Manganese in Gasoline By Atomic Absorption Spectroscopy |
ASTM D 4175 : 2019 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
ASTM D 1266 : 2007 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
ASTM D 4176 : 2004 : EDT 1 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 4814 : 2018 : REV C | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2013 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2019 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 4176 : 2002 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
ASTM D 4175 : 2015 : REV B : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 5191 : 2010 : REV B | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 5845 : 2001 | Standard Test Method for Determination of MTBE, ETBE, TAME, DIPE, Methanol, Ethanol and <i>tert-</i>Butanol in Gasoline by Infrared Spectroscopy |
ASTM D 5983 : 2015 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 6378 : 2007 | Standard Test Method for Determination of Vapor Pressure (VP<inf>X</inf>) of Petroleum Products, Hydrocarbons, and Hydrocarbon-Oxygenate Mixtures (Triple Expansion Method) |
ASTM D 5453 : 2003 : REV A | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 4814 : 2007 : REV B | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 2699 : 2010 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5191 : 2013 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 3237 : 2012 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
ASTM D 4953 : 2006 | Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method) |
ASTM D 7328 : 2007 : EDT 1 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
ASTM D 5191 : 2006 | Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method) |
ASTM D 4814 : 2013 : REV A | Standard Specification for Automotive Spark-Ignition Engine Fuel |
ASTM D 5854 : 1996 : R2015 | Standard Practice for Mixing and Handling of Liquid Samples of Petroleum and Petroleum Products |
ASTM D 2699 : 2019 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
ASTM D 2700 : 2004 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 1266 : 2018 | Standard Test Method for Sulfur in Petroleum Products (Lamp Method) |
ASTM D 7319 : 2013 | Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography |
ASTM D 4175 : 2008 : REV B | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
ASTM D 4306 : 2012 | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
ASTM D 4176 : 2004 | Standard Test Method for Free Water and Particulate Contamination in Distillate Fuels (Visual Inspection Procedures) |
ASTM D 5983 : 1997 | Standard Specification for Methyl <I>Tertiary</I>-Butyl Ether (MTBE) for Downstream Blending for Use in Automotive Spark-Ignition Engine Fuel |
ASTM D 2700 : 2008 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
ASTM D 5983 : 2018 | Standard Specification for Methyl Tertiary-Butyl Ether (MTBE) for Blending With Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2008 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
ASTM D 7862 : 2017 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
ASTM D 5453 : 2000 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet Fluorescence |
ASTM D 4306 : 2012 : REV C | Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.