Skip to content
Please enter a keyword to search

  • ASTM D 8175 : 2018

    Current The latest, up-to-date edition.

    Standard Test Method for Finite Flash Point Determination of Liquid Wastes by Pensky-Martens Closed Cup Tester

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  15-03-2018

    Publisher:  American Society for Testing and Materials

    Add To Cart

    Abstract - (Show below) - (Hide below)

    CONTAINED IN VOL. 11.04, 2018 Defines the procedure for a finite flash point test, within the range of 20 to 70 degrees C, of liquid wastes using a manual or automated Pensky-Martens closed cup tester.

    Scope - (Show below) - (Hide below)

    1.1This test method covers the procedure for a finite flash point test, within the range of 20 to 70 °C, of liquid wastes using a manual or automated Pensky-Martens closed cup tester.

    1.2This test method contains two procedures and is applicable to liquid waste, liquid phase(s) of multi-phase waste, liquid waste with suspended solids, or liquid waste that tends to form a surface film under test conditions.

    Note 1:If the liquid waste is of a viscosity such that the subsample volume will not be uniformly heated under the test conditions even with the increased stir rate of Procedure B, then use the small-scale method (Test Method D8174 for Finite Flash Point Determination of Liquid Wastes by Small-Scale Closed Cup Tester).

    1.3Procedure A is applicable to non-viscous liquids that are without suspended solids. Procedure B is applicable to viscous liquids, liquids with suspended solids, or liquids that form films.

    Note 2:This test method is not applicable for corrosive liquid wastes (see Test Method D8174).

    1.4Units—The values given in SI units are to be regarded as the standard.

    1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning statements appear throughout. Also see applicable Safety Data Sheets (SDS) for information about certified reference materials (CRMs) or secondary working standards (SWSs) that may be used in the analysis. SDS may also be useful if some components of the waste sample are known.

    1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    General Product Information - (Show below) - (Hide below)

    Committee D 34
    Document Type Test Method
    Product Note THIS STANDARD ALSO REFERS TO ISO 60751
    Publisher American Society for Testing and Materials
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 2719:2016 Determination of flash point — Pensky-Martens closed cup method
    ASTM D 6299 : 2010 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ISO 17034:2016 General requirements for the competence of reference material producers
    ASTM D 6299 : 2013 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2017 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2017 : REV B Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2009 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 502 : 2021 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
    ASTM D 6299 : 2013 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2021 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2007 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 6299 : 2010 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2022 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2003 : REV A Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 93 : 2019 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
    ASTM D 6299 : 2023 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2003 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM E 2251 : 2014 : R2021 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
    ASTM D 6299 : 2000 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
    ISO Guide 35:2017 Reference materials Guidance for characterization and assessment of homogeneity and stability
    ASTM D 6299 : 2010 : EDT 2 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 502 : 2007 : R2013 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
    ASTM E 502 : 2007 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
    ASTM D 6299 : 2016 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2014 : REDLINE Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 6299 : 2019 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2010 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 6299 : 2023 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2000 : REV A Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
    ASTM E 2251 : 2011 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM E 2251 : 2014 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
    ASTM D 6299 : 2023 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2020 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2008 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 93 : 2016-07 TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER
    ASTM D 6299 : 2002 : EDT 1 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
    ASTM D 6299 : 2022 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
    ASTM D 6299 : 2007 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2007 : EDT 1 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2020 : REV A Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 6299 : 2017 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
    ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
    ASTM E 502 : 2021 : REV A Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
    ASTM D 93 : 2018 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
    ASTM D 6299 : 2002 Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective