ASTM D 876 : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
03-03-2021
English
01-11-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 10.01, 2015 Defines the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C) nonrigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
| Committee |
D 09
|
| DocumentType |
Redline
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1These test methods cover the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 nonrigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation. For the purpose of these test methods nonrigid tubing shall be tubing having an initial elongation in excess of 100 % at break.
1.2The values stated in inch-pound units are to be regarded as standard, except for temperature, which shall be expressed in degrees Celsius. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3The procedures appear in the following sections:
| | | ASTM Reference Standard |
| Brittleness Temperature | 43 – 45 | D746 |
| Corrosion Tests | 74 – 85 | D1000 |
| Dielectric Breakdown Voltage at High Humidity | 65 – 73 | E104 |
| Dielectric Breakdown Voltage | 58 – 64 | D149 |
| Dimensional Tests | 8 – 14 | D374 |
| Effect of Elevated Temperatures | 25 – 36 | D412 |
| Flammability Test | 15 – 21 | |
| Oil Resistance Test | 35 – 42 | D471 |
| Penetration Test | 46 – 51 | |
| Sampling | 6 | |
| Strain Relief Test | 68 – 73 | |
| Tension Test | 22 – 24 | D412 |
| Test Conditions | 7 | |
| Volume Resistivity | 52 – 57 | D257 |
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.
1.5For fire test caveats, see Section 15.
| SAE AMS 3655D :2016 | TUBING, ELECTRICAL INSULATION, THIN WALL, EXTRUDED POLYTETRAFLUOROETHYLENE (PTFE) |
| SAE AS 81914 : 2016 | TUBING, PLASTIC, FLEXIBLE, CONVOLUTED, CONDUIT, GENERAL SPECIFICATION FOR |
| MIL-PRF-46846 Revision D:2013 | Rubber, Synthetic, Heat - Shrinkable |
| SAE AS85080A | Insulation Sleeving, Electrical, Shrinkable Without Heat, General Specification For |
| MIL-H-24520 Base Document:1975 | MILITARY SPECIFICATION - HOSE AND HOSE ASSEMBLY FOR WATER COOLING OF ELECTRONIC EQUIPMENT |
| MIL-I-82799 Base Document:1989 | INSULATION SLEEVING, ELECTRICAL, HEAT-SHRINKABLE |
| ASTM D 2484 : 2006 : R2012 : EDT 1 | Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2020) |
| MIL I 23053 : D | INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE MODIFIED FLUOROPOLYMER, CROSSLINKED |
| MIL R 46846 : B | RUBBER, SYNTHETIC, HEAT-SHRINKABLE |
| SAE AMST81914A | Tubing, Plastic, Flexible, Convoluted, Conduit, General Specification For |
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| ASTM D 350 : 2013 : REDLINE | Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation |
| ASTM D 1675 : 2003 : R2011 | Standard Test Methods for Polytetrafluoroethylene Tubing |
| ASTM D 3006 : 2010 : R2017 | Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape (Withdrawn 2022) |
| SAE AS23053 | Insulation Sleeving, Electrical, Heat Shrinkable, General Specification For |
| MIL-DTL-83723-27 Revision C:2015 | CONNECTORS, ELECTRICAL, BACKSHELL, WITH HEAT-SHRINKABLE STRAIN-RELIEF BOOT (STRAIGHT AND RIGHT ANGLE), THREADED COUPLING |
| CSA C22.2 No. 198.1 : 2006 : R2015 | EXTRUDED INSULATING TUBING |
| SAE AMS 3653 : 2016 | TUBING, ELECTRICAL INSULATION, STANDARD WALL, EXTRUDED POLYTETRAFLUOROETHYLENE (PTFE) |
| ASTM D 2484 : 2006 | Standard Specification for Polyester Film Pressure-Sensitive Electrical Insulating Tape |
| ASTM D 2671 : 2013 | Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use |
| MIL-T-81914 Base Document:1973 | TUBING, PLASTIC, FLEXIBLE, CONVOLUTED, CONDUIT, GENERAL SPECIFICATION FOR |
| MIL-I-22076 Revision B:1963 | INSULATION TUBING, ELECTRICAL, NONRIGID, VINYL, VERY LOW TEMPERATURE GRADE |
| CSA C22.2 No. 198.1 : 2006 | EXTRUDED INSULATING TUBING |
| ASTM D 3006 : 2010 | Standard Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape |
| MIL-I-7444 Revision D:1984 | INSULATION SLEEVING, ELECTRICAL FLEXIBLE |
| MIL-T-47051 Revision A:1974 | TUBING, HEAT SHRINKABLE |
| MIL-I-3190 Revision F:1991 | INSULATION SLEEVING, ELECTRICAL, FLEXIBLE, COATED, GENERAL SPECIFICATION FOR |
| MIL-DTL-23053 Revision E:1996 | INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR |
| MIL-I-631 Revision D:1961 | INSULATION, ELECTRICAL, SYNTHETIC - RESIN COMPOSITION, NONRIGID |
| MIL-I-22129 Revision C:1962 | INSULATION TUBING, ELECTRICAL, POLYTETRAFLUOROETHYLENE RESIN, NONRIGID (SEE ASTM D 3295) |
| SAE AMSDTL23053 | Insulation Sleeving, Electrical, Heat Shrinkable, General Specification For |
| ASTM D 922 : 2011-09 | SPECIFICATION FOR NONRIGID VINYL CHLORIDE POLYMER TUBING |
| ASTM D 1675 : 2003 | Standard Test Methods for Polytetrafluoroethylene Tubing |
| IEC 60684-2:2011 | Flexible insulating sleeving - Part 2: Methods of test |
| ASTM D 1711 : 2015 : REDLINE | Standard Terminology Relating to Electrical Insulation |
| ASTM E 104 : 2002 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions |
| ASTM D 257 : 2014 : REDLINE | Standard Test Methods for DC Resistance or Conductance of Insulating Materials |
| ASTM D 1000 : 2017 : REDLINE | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
| ASTM D 746 : 2014 : REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.