![header thumbnail](/images/publishers\astm_cover.gif)
ASTM D 95 : 2013 : R2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
Hardcopy , PDF
16-11-2023
English
27-11-2018
1.1This test method covers the determination of water in the range from 0 % to 25 % by volume in petroleum products, tars, and other bituminous materials by the distillation method.
Committee |
D 02
|
DocumentType |
Test Method
|
Pages |
6
|
ProductNote |
THIS STANDARD ALSO REFERS TO MPMS Chapter 8.1, MPMS Chapter 8.2, MPMS Chapter 8.3, MPMS Chapter 10.2, MPMS Chapter 10.6
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This test method covers the determination of water in the range from 0 % to 25 % by volume in petroleum products, tars, and other bituminous materials by the distillation method.
Note 1:Volatile water-soluble material, if present, may be measured as water.
1.2The specific products considered during the development of this test method are listed in Table 1. For bituminous emulsions refer to Test Method D244. For crude oils, refer to Test Method D4006 (API MPMS Chapter 10.2).
Note 2:With some types of oil, satisfactory results may be obtained from Test Method D1796 (API MPMS Chapter 10.6).
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 4072 : 2023 | Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch |
ASTM D 6448 : 2016 : R2022 | Standard Specification for Industrial Burner Fuels from Used Lubricating Oils |
ASTM D 6373 : 2023 | Standard Specification for Performance-Graded Asphalt Binder |
ASTM E 1417/E1417M : 2021 : EDT 1 | Standard Practice for Liquid Penetrant Testing |
ASTM D 2027/D2027M : 2019 | Standard Specification for Cutback Asphalt (Medium-Curing Type) |
ASTM D 6666 : 2020 | Standard Guide for Evaluation of Aqueous Polymer Quenchants |
ASTM D 6511/D6511M : 2018 | Standard Test Methods for Solvent Bearing Bituminous Compounds |
ASTM D 2318 : 2020 | Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch |
ASTM D 6224 : 2022 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
ASTM D 5643/D5643M : 2006 : R2018 | Standard Specification for Coal Tar Roof Cement, Asbestos Free |
ASTM D 450/D450M : 2007 : R2018 | Standard Specification for Coal-Tar Pitch Used in Roofing, Dampproofing, and Waterproofing |
ASTM D 228/D228M : 2021 | Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing |
ASTM D 8125 : 2018 : R2023 | Standard Specification for Re-Refined Engine Oil Bottoms (REOB)/Vacuum Tower Asphalt Extender (VTAE) |
ASTM D 4868 : 2017 | Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels |
ASTM D 7665 : 2022 | Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids |
ASTM D 7044 : 2015 | Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids (Withdrawn 2024) |
ASTM D 6626 : 2015 : R2021 | Standard Specification for Performance-Graded Trinidad Lake Modified Asphalt Binder |
ASTM D 8239 : 2023 | Standard Specification for Performance-Graded Asphalt Binder Using the Multiple Stress Creep and Recovery (MSCR) Test |
ASTM D 7280 : 2020 | Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch by Stainless Steel Crucible Filtration |
ASTM D 2028/D2028M : 2015 : R2021 : EDT 1 | Standard Specification for Cutback Asphalt (Rapid-Curing Type) |
ASTM D 3712 : 2018 | Standard Test Method of Analysis of Oil-Soluble Sulfonates by Liquid Chromatography |
ASTM D 2523/D2523M : 2013 : R2019 : EDT 1 | Standard Practice for Testing Load-Strain Properties of Roofing Membranes |
ASTM D 7832/D7832M : 2014 : R2021 | Standard Guide for Performance Attributes of Waterproofing Membranes Applied to Below-Grade Walls / Vertical Surfaces (Enclosing Interior Spaces) |
ASTM D 128 : 1998 : R2019 | Standard Test Methods for Analysis of Lubricating Grease |
ASTM D 4312 : 2020 | Standard Test Method for Toluene-Insoluble (TI) Content of Tar and Pitch (Short Method) |
ASTM D 4746 : 2020 | Standard Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration |
ASTM D 3381/D3381M : 2018 | Standard Specification for Viscosity-Graded Asphalt Binder for Use in Pavement Construction |
ASTM D 6823 : 2008 : R2021 | Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils |
ASTM D 8099/D8099M : 2017 : R2023 | Standard Specification for Asphalt Emulsion Pavement Sealer (Mineral Colloid or Chemically Stabilized Type) |
ASTM D 6710 : 2021 | Standard Guide for Evaluation of Hydrocarbon-Based Quench Oil |
ASTM D 396 : 2021 | Standard Specification for Fuel Oils |
ASTM D 7666 : 2012 : R2019 | Standard Specification for Triglyceride Burner Fuel |
ASTM D 2026/D2026M : 2015 : R2021 : EDT 1 | Standard Specification for Cutback Asphalt (Slow-Curing Type) |
ASTM D 3326 : 2007 : R2017 | Standard Practice for Preparation of Samples for Identification of Waterborne Oils |
ASTM D 5147/D5147M : 2018 | Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material |
ASTM D 6630/D6630M : 2016 : R2022 | Standard Guide for Low-Slope Insulated Roof Membrane Assembly Performance |
ASTM D 4073/D4073M : 2006 : R2019 : EDT 1 | Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes |
ASTM D 1208 : 1996 : R2019 | Standard Test Methods for Common Properties of Certain Pigments |
ASTM D 146/D146M : 2004 : R2020 | Standard Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing |
ASTM D 2982 : 2007 : R2019 | Standard Test Methods for Detecting Glycol-Base Antifreeze in Used Lubricating Oils |
ASTM D 5372 : 2020 | Standard Guide for Evaluation of Hydrocarbon Heat Transfer Fluids |
ASTM D 5727/D5727M : 2000 : R2023 | Standard Specification for Emulsified Refined Coal Tar (Mineral Colloid Type) |
ASTM D 6626 : 2023 | Standard Specification for Performance-Graded Trinidad Lake Modified Asphalt Binder |
ASTM D 6224 : 2023 | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
ASTM D 244 : 2023 | Standard Test Methods and Practices for Emulsified Asphalts |
ASTM D 235 : 2022 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) |
ASTM E 123 : 1992 : R1996 | Standard Specification for Apparatus for Determination of Water by Distillation |
ASTM D 235 : 2002 : R2012 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021) |
ASTM E 123 : 1992 | Standard Specification for Apparatus for Determination of Water by Distillation |
ASTM D 244 : 2009 : R2017 | Standard Test Methods and Practices for Emulsified Asphalts |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.