![header thumbnail](/images/publishers\astm_cover.gif)
ASTM E 1514 : 1998 : R2017 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Specification for Structural Standing Seam Steel Roof Panel Systems
Hardcopy , PDF
09-01-2024
English
08-11-2017
CONTAINED IN VOL. 04.11, 2017 Defines the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only: panels, concealed panel clips, panel/clip anchorage, and panel joint sealers.
Committee |
E 06
|
DocumentType |
Standard
|
Pages |
5
|
ProductNote |
Reconfirmed EDT 1
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1This specification covers the design, construction, and weatherability of structural standing seam steel roof panel systems. It includes performance requirements for the following elements only: panels, concealed panel clips, panel/clip anchorage, and panel joint sealers.
Note 1:These systems are used on both low-slope and steep-slope roof applications. They also are used with or without an underlying deck or sheathing.
1.2The objective of this specification is to provide for the overall performance of the structural standing seam steel roof panel system as defined in 3.2.6 during its service life in order to provide weather protection, carry the specified design loads, and allow proper access over the roof surface in order to provide for periodic maintenance of equipment by the owner.
1.3In addition to structural, the specifier shall evaluate other characteristics beyond the scope of this specification that affect the final choice of roof construction. These include, but are not limited to, functional, legal, insurance, and economic considerations. See Appendix X1 for specifier's checklist.
1.4The specification is not intended to exclude products or systems not covered by the referenced documents.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6The text of this specification contains notes and footnotes that provide explanatory information and are not requirements of this specification.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM A 875/A875M : 2013 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM C 765 : 1997 : R2015 | Standard Test Method for Low-Temperature Flexibility of Preformed Tape Sealants |
ASTM C 711 : 2022 | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
ASTM A 653/A653M : 2001 : REV A | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM E 1592 : 2005 : R2017 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
ASTM A 653/A653M : 2023 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM E 1680 : 2016 : REDLINE | Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems |
ASTM A 463/A463M : 2015 : R2020 : EDT 1 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM G 21 : 2015 : REDLINE | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
ASTM E 1646 : 1995 : R2018 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
ASTM E 1646 : 1995 : R2003 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
ASTM E 1592 : 2001 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
ASTM C 711 : 2014 : REDLINE | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM A 653/A653M : 2022 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM D 3310 : 2000 : R2006 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
ASTM A 875/A875M : 2013 : REDLINE | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM A 792/A792M : 2009 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM A 653/A653M : 2020 | Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process |
ASTM E 1646 : 1995 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
ASTM D 1667 : 1976 : R1990 | Standard Specification for Flexible Cellular MaterialsÐVinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
ASTM A 875/A875M : 2013 : R2021 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 1667 : 2005 | Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
ASTM D 1667 : 1997 | Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam) |
ASTM E 1646 : 1995 : R2011 | Standard Test Method for Water Penetration of Exterior Metal Roof Panel Systems by Uniform Static Air Pressure Difference |
ASTM A 792/A792M : 2022 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM E 1680 : 2011 | Standard Test Method for Rate of Air Leakage Through Exterior Metal Roof Panel Systems |
ASHRAE HDBK FUNDAMENTALS : 2013 | ASHRAE HANDBOOK - FUNDAMENTALS |
ASTM A 875/A875M : 2023 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM A 463/A463M : 2022 | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM D 1667 : 2022 | Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell) |
ASTM A 463/A463M : 2015 : REDLINE | Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip Process |
ASTM D 3310 : 2000 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
ASTM A 875/A875M : 2022 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 3310 : 2000 : R2023 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
ASTM E 1592 : 1998 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
ASTM C 711 : 2014 | Standard Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants |
ASTM C 765 : 2023 | Standard Test Method for Low-Temperature Flexibility of Preformed Tape Sealants |
ASTM E 1680 : 2016 | Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems |
ASTM D 1667 : 2005 : R2011 | Standard Specification for Flexible Cellular Materials<char: emdash>Poly (Vinyl Chloride) Foam (Closed-Cell) |
ASTM A 792/A792M : 2010 : R2015 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM D 3310 : 2000 : R2014 | Standard Test Method for Determining Corrosivity of Adhesive Materials |
ASTM A 792/A792M : 2023 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
FM 4471 : 2010 | CLASS 1 PANEL ROOFS |
ASTM A 875/A875M : 2021 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM D 1667 : 2017 : REDLINE | Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell) |
ASTM A 792/A792M : 2021 : REV A | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM E 1680 : 1995 | Standard Test Method for Rate of Air Leakage Through Exterior Metal Roof Panel Systems |
ASTM A 875/A875M : 2009 | Standard Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process |
ASTM G 21 : 2015 | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
UL 580:5ED 2006-11-02 | Tests for Uplift Resistance of Roof Assemblies |
ASTM A 792/A792M : 2021 | Standard Specification for Steel Sheet, 55 % Aluminum-Zinc Alloy-Coated by the Hot-Dip Process |
ASTM E 1592 : 2005 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
ASTM G 21 : 2015 : R2021 : EDT 1 | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
ASTM D 1667 : 2017 | Standard Specification for Flexible Cellular Materials—Poly (Vinyl Chloride) Foam (Closed-Cell) |
ASTM E 1680 : 2016 : R2022 | Standard Test Method for Rate of Air Leakage through Exterior Metal Roof Panel Systems |
ASTM E 1592 : 2005 : R2012 | Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.