![header thumbnail](/images/publishers\astm_cover.gif)
ASTM E 2777 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Guide for Vegetative (Green) Roof Systems
Hardcopy , PDF
26-08-2020
English
01-05-2014
CONTAINED IN VOL. 04.12, 2015 Defines terminology, principles and fundamental concepts including those related to sustainability, technical requirements of construction, and types of vegetative (green) roof systems used on buildings.
Committee |
D 08
|
DocumentType |
Guide
|
Pages |
14
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1This guide identifies terminology, principles and fundamental concepts including those related to sustainability, technical requirements of construction, and types of vegetative (green) roof systems used on buildings.
1.2The considerations for sustainable development relative to vegetative (green) roof systems are categorized as follows: environmental, social, and economic as consistent with Guide E2432. (See Appendix X1.)
1.3This guide discusses technical requirements for vegetative (green) roof systems pertaining to the following categories: plants, media, wind scour resistance, soil reinforcement, separation or filter layers, drain layers, water retention layers, protection layers, and root penetration barriers.
1.4This guide addresses intensive and extensive vegetative (green) roof systems for roofs up to 15 % slope. Roofing/waterproofing membranes and insulation are key components of vegetative (green) roof systems, but technical requirements regarding their role in such roof systems is beyond the scope of this guide.
1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM E 2788/E2788M : 2018 | Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems |
ASTM D 8014 : 2017 | Standard Guide for Selection of Membranes Used in Vegetative Roofing Systems |
ASTM E 2400 : 2006 | Standard Guide for Selection, Installation, and Maintenance of Plants for Green Roof Systems |
ASTM D 4759 : 2011 | Standard Practice for Determining the Specification Conformance of Geosynthetics |
ASTM D 4439 : 2020 | Standard Terminology for Geosynthetics |
ASTM D 6637 : 2010 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method |
ASTM E 631 : 2015 : REDLINE | Standard Terminology of Building Constructions |
ASTM D 1079 : 2008 : REV A | Standard Terminology Relating to Roofing and Waterproofing |
ASTM E 2432 : 2019 | Standard Guide for General Principles of Sustainability Relative to Buildings |
ASTM D 1987 : 2018 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM D 5262 : 2006 | Standard Test Method for Evaluating the Unconfined Tension Creep Rupture Behavior of Geosynthetics |
ASTM D 4439 : 2015 | Standard Terminology for Geosynthetics |
ASTM D 1987 : 2007 : R2016 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM D 4873 : 1997 | Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples |
ASTM D 4354 : 2012 | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
ASTM D 4751 : 2016 : REDLINE | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
ASTM E 2114 : 2005 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 1079 : 2016 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 1079 : 2006 | Terminology Relating to Roofing and Waterproofing |
ASTM C 88 : 2013-08 | TEST METHOD FOR SOUNDNESS OF AGGREGATES BY USE OF SODIUM SULFATE OR MAGNESIUM SULFATE |
ASTM E 2114 : 2005 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM E 2114 : 2019 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 2974 : 2007 : REV A | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM D 5617 : 2004 : R2010 | Standard Test Method for Multi-Axial Tension Test for Geosynthetics |
ASTM D 4873 : 2001 | Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples |
ASTM D 4491 : 1999 : REV A : R2009 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM E 2399 : 2011 | Standard Test Method for Maximum Media Density for Dead Load Analysis of Vegetative (Green) Roof Systems |
ASTM D 5262 : 2007 : R2016 | Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics |
ASTM D 5818 : 2011 | Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics |
ASTM D 5818 : 1995 : R2000 | Standard Practice for Obtaining Samples of Geosynthetics from a Test Section for Assessment of Installation Damage |
ASTM D 4595 : 1986 : R2001 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 7361 : 2007 : R2012 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 4439 : 2011 | Standard Terminology for Geosynthetics |
ASTM D 4873 : 2002 | Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples |
ASTM E 2398 : 2011 | Standard Test Method for Water Capture and Media Retention of Geocomposite Drain Layers for Vegetative (Green) Roof Systems |
ASTM D 7361 : 2007 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 5262 : 2004 | Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics |
ASTM D 4439 : 2015 : REV A | Standard Terminology for Geosynthetics |
ASTM E 2114 : 2006 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 1079 : 2013 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM E 2432 : 2005 | Standard Guide for General Principles of Sustainability Relative to Buildings |
ASTM D 4751 : 1999 : REV A | Standard Test Method for Determining Apparent Opening Size of a Geotextile |
ASTM D 1079 : 2007 : REV A | Terminology Relating to Roofing and Waterproofing |
ASTM E 108 : 2017 : REDLINE | Standard Test Methods for Fire Tests of Roof Coverings |
ASTM D 1079 : 2010 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 4751 : 2004 | Standard Test Method for Determining Apparent Opening Size of a Geotextile |
ASTM D 1987 : 2007 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM E 2114 : 2001 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 4491 : 1999 : REV A : R2004 : EDT 1 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM E 2788 : 2011 | Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems |
ASTM D 4759 : 2011 : R2018 | Standard Practice for Determining the Specification Conformance of Geosynthetics |
ASTM D 4439 : 2002 | Standard Terminology for Geosynthetics |
ASTM E 2432 : 2017 : REDLINE | GUIDE FOR GENERAL PRINCIPLES OF SUSTAINABILITY RELATIVE TO BUILDINGS |
ASTM E 2398 : 2005 | Standard Test Method for Water Capture and Media Retention of Geocomposite Drain Layers for Green Roof Systems |
ASTM E 2114 : 2004 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM E 2399 : 2005 | Standard Test Method for Maximum Media Density for Dead Load Analysis of Green Roof Systems |
ASTM D 4595 : 2011 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 5818 : 2006 | Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics |
ASTM E 2396 : 2011 | Standard Test Method for Saturated Water Permeability of Granular Drainage Media [Falling-Head Method] for Vegetative (Green) Roof Systems |
ASTM E 2114 : 2017 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 1079 : 2018 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 5262 : 2002 : REV A | Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics |
ASTM D 5262 : 1997 | Standard Test Method for Evaluating the Unconfined Tension Creep Behavior of Geosynthetics |
ASTM D 2974 : 2000 | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM D 4759 : 2002 | Standard Practice for Determining the Specification Conformance of Geosynthetics |
ASTM D 4439 : 2017 | Standard Terminology for Geosynthetics |
ASTM D 4751 : 1999 : REV A : R2004 | Standard Test Method for Determining Apparent Opening Size of a Geotextile |
ASTM D 5818 : 2011 : R2018 | Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics |
ASTM E 2396 : 2005 | Standard Test Method for Saturated Water Permeability of Granular Drainage Media [Falling-Head Method] for Green Roof Systems |
ASTM D 5262 :2007 | Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics |
ASTM D 4873 : 2015 | Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples |
ASTM D 2974 : 2007 | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM D 4595 : 1986 : R1994 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 4491 : 1999 : REV A : R2014 : EDT 1 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM D 1079 : 2005 : REV A | Terminology Relating to Roofing and Waterproofing |
ASCE 7 10 : 2010 | MINIMUM DESIGN LOADS FOR BUILDINGS AND OTHER STRUCTURES |
ASTM D 6637 : 2001 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method |
ASTM D 6637 : 2011 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method |
ASTM E 2397 : 2011 | Standard Practice for Determination of Dead Loads and Live Loads Associated with Vegetative (Green) Roof Systems |
ASTM D 6637 : 2001 : R2009 | Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method |
ASTM D 1079 : 2002 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 2974 : 2014 | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM D 2974 : 2014 : REDLINE | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM E 2114 : 2008 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 5262 : 2007 : R2012 | Standard Test Method for Evaluating the Unconfined Tension Creep and Creep Rupture Behavior of Geosynthetics |
ASTM D 2974 : 2013 | Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils |
ASTM D 4759 : 2002 : R2007 | Standard Practice for Determining the Specification Conformance of Geosynthetics |
ASTM D 4751 : 2012 | Standard Test Method for Determining Apparent Opening Size of a Geotextile |
ASTM D 4439 : 2001 | Standard Terminology for Geosynthetics |
ASTM E 2432 : 2011 | Standard Guide for General Principles of Sustainability Relative to Buildings |
ASTM D 4439 : 2014 | Standard Terminology for Geosynthetics |
ASTM D 4354 : 1999 : R2009 | Standard Practice for Sampling of Geosynthetics for Testing |
ASTM D 1079 : 2001 | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM D 4595 : 2017 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 4354 : 2012 : REDLINE | Standard Practice for Sampling of Geosynthetics and Rolled Erosion Control Products(RECPs) for Testing |
ASTM D 1987 : 2007 : R2012 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM E 2114 : 2006 | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 1987 : 1995 | Standard Test Method for Biological Clogging of Geotextile or Soil/Geotextile Filters |
ASTM D 4354 : 1999 | Standard Practice for Sampling of Geosynthetics for Testing |
ASTM D 4759 : 1988 : R1996 | Standard Practice for Determining the Specification Conformance of Geosynthetics |
ASTM D 4439 : 2004 | Standard Terminology for Geosynthetics |
ASTM D 4595 : 2009 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 5617 : 2004 | Standard Test Method for Multi-Axial Tension Test for Geosynthetics |
ASTM D 4873 : 2002 : R2009 | Standard Guide for Identification, Storage, and Handling of Geosynthetic Rolls and Samples |
ASTM D 4439 : 2017-08 | TERMINOLOGY FOR GEOSYNTHETICS |
ASTM D 1079 : 2000 : REV A | Standard Terminology Relating to Roofing, Waterproofing, and Bituminous Materials |
ASTM E 2397 : 2005 | Standard Practice for Determination of Dead Loads and Live Loads associated with Green Roof Systems |
ASTM D 7361 : 2007 : R2018 | Standard Test Method for Accelerated Compressive Creep of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method |
ASTM D 4751 : 2016 | Standard Test Methods for Determining Apparent Opening Size of a Geotextile |
ASTM D 4439 : 2000 | Standard Terminology for Geosynthetics |
ASTM D 4491 : 1999 : REV A | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM E 2114 : 2017-03 | TERMINOLOGY FOR SUSTAINABILITY RELATIVE TO THE PERFORMANCE OF BUILDINGS |
ASTM D 4491 : 1999 : REV A : R2004 | Standard Test Methods for Water Permeability of Geotextiles by Permittivity |
ASTM D 4354 : 1999 : R2004 | Standard Practice for Sampling of Geosynthetics for Testing |
ASTM E 2114 : 2000 : REV A | Standard Terminology for Sustainability Relative to the Performance of Buildings |
ASTM D 5617 : 2004 : R2015 | Standard Test Method for Multi-Axial Tension Test for Geosynthetics |
ASTM D 1079 : 2013 : EDT 1 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 4439 : 2018 | Standard Terminology for Geosynthetics |
ASTM D 4595 : 2005 | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 4595 : 2017 : REDLINE | Standard Test Method for Tensile Properties of Geotextiles by the Wide-Width Strip Method |
ASTM D 1079 : 2009 | Standard Terminology Relating to Roofing and Waterproofing |
ASTM D 5617 : 1999 : EDT 1 | Standard Test Method for Multi-Axial Tension Test for Geosynthetics |
ASTM E 2432 : 2017 | Standard Guide for General Principles of Sustainability Relative to Buildings |
ASTM D 4716/D4716M : 2014 : REDLINE | Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.