![header thumbnail](/images/publishers\astm_cover.gif)
ASTM E 8/E8M : 2016 : REV A : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/publishers\astm_cover.gif)
Standard Test Methods for Tension Testing of Metallic Materials
Hardcopy , PDF
24-02-2021
English
11-02-2020
Committee |
E 28
|
DocumentType |
Test Method
|
Pages |
30
|
ProductNote |
9.1 was editorially corrected in February 2020.
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy |
1.1These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
1.2The gauge lengths for most round specimens are required to be 4D for E8 and 5D for E8M. The gauge length is the most significant difference between E8 and E8M test specimens. Test specimens made from powder metallurgy (P/M) materials are exempt from this requirement by industry-wide agreement to keep the pressing of the material to a specific projected area and density.
1.3Exceptions to the provisions of these test methods may need to be made in individual specifications or test methods for a particular material. For examples, see Test Methods and Definitions A370 and Test Methods B557, and B557M.
1.4Room temperature shall be considered to be 10 to 38°C [50 to 100°F] unless otherwise specified.
1.5The values stated in SI units are to be regarded as separate from inch/pound units. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E 531 : 2013 | Standard Practice for Surveillance Testing of High-Temperature Nuclear Component Materials (Withdrawn 2022) |
ASTM E 2218 : 2015 | Standard Test Method for Determining Forming Limit Curves |
ASTM B 99/B99M : 2015 | Standard Specification for Copper-Silicon Alloy Wire for General Applications |
ASTM B 249/B249M : 2020 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings |
ASTM B 1003 : 2016 | Standard Specification for Seamless Copper Tube for Linesets |
ASTM B 691 : 2018 | Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08367) Rod, Bar, and Wire |
ASTM B 49 : 2020 | Standard Specification for Copper Rod for Electrical Purposes |
ASTM F 2066 : 2018 | Standard Specification for Wrought Titanium-15 Molybdenum Alloy for Surgical Implant Applications (UNS R58150) |
ASTM B 936 : 2019 | Standard Specification for Copper-Chromium-Iron-Titanium Alloy Plate, Sheet, Strip and Rolled Bar |
ASTM B 599 : 2020 | Standard Specification for Nickel-Iron-Chromium-Molybdenum-Niobium Stabilized Alloy Plate, Sheet, and Strip |
ASTM E 6 : 2015 : EDT 3 | Standard Terminology Relating to Methods of Mechanical Testing |
ASTM B 168 : 2019 | Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS N06235) Plate, Sheet, and Strip |
ASTM B 882 : 2010 : R2018 | Standard Specification for Pre-Patinated Copper for Architectural Applications |
ASTM F 1472 : 2020 : REV A | Standard Specification for Wrought Titanium-6Aluminum-4Vanadium Alloy for Surgical Implant Applications (UNS R56400) |
ASTM A 888 : 2020 | Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications |
ASTM A 231/A231M : 2018 | Standard Specification for Chromium-Vanadium Alloy Steel Spring Wire |
ASTM A 571/A571M : 2001 : R2019 | Standard Specification for Austenitic Ductile Iron Castings for Pressure-Containing Parts Suitable for Low-Temperature Service |
ASTM B 393 : 2018 | Standard Specification for Niobium and Niobium Alloy Strip, Sheet, and Plate |
ASTM B 150/B150M : 2019 | Standard Specification for Aluminum Bronze Rod, Bar, and Shapes |
ASTM B 159/B159M : 2017 | Standard Specification for Phosphor Bronze Wire |
ASTM B 475 : 2007 : R2018 | Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Round Weaving Wire |
ASTM B 974/B974M : 2016 : R2021 | Standard Specification for Free-Cutting Bismuth Brass Rod, Bar and Wire |
ASTM A 401/A401M : 2018 | Standard Specification for Steel Wire, Chromium-Silicon Alloy |
ASTM E 2634 : 2018 | Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems |
ASTM F 1350 : 2015 | Standard Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Surgical Fixation Wire (UNS S31673) |
ASTM A 942/A942M : 1995 : R2018 | Standard Specification for Centrifugally Cast White Iron/Gray Iron Dual Metal Abrasion-Resistant Roll Shells |
ASTM B 570 : 2016 | Standard Specification for Copper-Beryllium Alloy (UNS Nos. C17000 and C17200) Forgings and Extrusions |
ASTM G 168 : 2017 | Standard Practice for Making and Using Precracked Double Beam Stress Corrosion Specimens |
ASTM B 360 : 2020 | Standard Specification for Hard-Drawn Copper Capillary Tube for Restrictor Applications |
ASTM D 7147 : 2011 : R2018 | Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers |
ASTM F 2924 : 2014 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion |
ASTM B 88 : 2020 | Standard Specification for Seamless Copper Water Tube |
ASTM B 804 : 2002 : R2018 | Standard Specification for UNS N08367 and UNS N08926 Welded Pipe |
ASTM F 2660 : 2020 | Standard Test Method for Qualifying Coatings for Use on F3125 Grade A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement |
ASTM B 371/B371M : 2019 | Standard Specification for Copper-Zinc-Silicon Alloy Rod |
ASTM F 1295 : 2016 | Standard Specification for Wrought Titanium-6Aluminum-7Niobium Alloy for Surgical Implant Applications (UNS R56700) |
ASTM B 1001 : 2017 | Standard Specification for Copper Electrode Wire Used for Welding Seams of Steel Cans |
ASTM F 2855 : 2019 | Standard Specification for Chlorinated Poly(Vinyl Chloride)/Aluminum/Chlorinated Poly(Vinyl Chloride) (CPVC-AL-CPVC) Composite Pressure Tubing |
ASTM B 654/B654M : 2010 : R2018 | Standard Specification for Niobium-Hafnium Alloy Foil, Sheet, Strip, and Plate |
ASTM B 394 : 2018 | Standard Specification for Niobium and Niobium Alloy Seamless and Welded Tubes |
ASTM F 2886 : 2017 | Standard Specification for Metal Injection Molded Cobalt-28Chromium-6Molybdenum Components for Surgical Implant Applications |
ASTM B 354 : 2019 | Standard Terminology Relating to Uninsulated Metallic Electrical Conductors |
ASTM B 747 : 2020 | Standard Specification for Copper-Zirconium Alloy Sheet and Strip |
ASTM F 2581 : 2012 : R2017 | Standard Specification for Wrought Nitrogen Strengthened 11Manganese-17Chromium-3Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29225) |
ASTM B 43 : 2020 | Standard Specification for Seamless Red Brass Pipe, Standard Sizes |
ASTM A 439/A439M : 2018 | Standard Specification for Austenitic Ductile Iron Castings |
ASTM E 290 : 2014 | Standard Test Methods for Bend Testing of Material for Ductility |
ASTM B 752/B752M : 2018 | Standard Specification for Castings, Zirconium-Base, Corrosion Resistant, for General Application |
ASTM E 2714 : 2013 : R2020 | Standard Test Method for Creep-Fatigue Testing |
ASTM B 937 : 2018 | Standard Specification for Copper-Beryllium Seamless Tube (UNS Nos. C17500 and C17510) |
ASTM B 166 : 2019 | Standard Specification for Nickel-Chromium-Aluminum Alloy, Nickel-Chromium-Iron Alloys, Nickel-Chromium-Cobalt-Molybdenum Alloy, Nickel-Iron-Chromium-Tungsten Alloy, and Nickel-Chromium-Molybdenum-Copper Alloy Rod, Bar, and Wire |
ASTM B 250/B250M : 2019 | Standard Specification for General Requirements for Wrought Copper Alloy Wire |
ASTM F 1387 : 2019 | Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings |
ASTM E 328 : 2021 | Standard Test Methods for Stress Relaxation for Materials and Structures |
ASTM E 111 : 2017 | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus |
ASTM B 981/B981M : 2019 | Standard Specification for Low-Leaded Brass Rod, Bar, Wire, and Shapes |
ASTM B 591 : 2020 : REV A | Standard Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled Bar |
ASTM B 88M : 2020 | Standard Specification for Seamless Copper Water Tube (Metric) |
ASTM A 447/A447M : 2011 : R2016 | Standard Specification for Steel Castings, Chromium-Nickel-Iron Alloy (25-12 Class), for High-Temperature Service |
ASTM A 1095 : 2015 : R2019 | Standard Specification for High-Silicon Molybdenum Ferritic Iron Castings |
ASTM B 453/B453M : 2019 | Standard Specification for Copper-Zinc-Lead Alloy (Leaded-Brass) Rod, Bar, and Shapes |
ASTM E 646 : 2016 | Standard Test Method for Tensile Strain-Hardening Exponents (<emph type="bdit">n</emph > -Values) of Metallic Sheet Materials |
ASTM A 230/A230M : 2019 | Standard Specification for Steel Wire, Carbon Valve Spring Quality |
ASTM A 878/A878M : 2019 | Standard Specification for Steel Wire, Modified Chromium Vanadium Valve Spring Quality |
ASTM B 194 : 2015 | Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM E 399 : 2020 : REV A | Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness of Metallic Materials |
ASTM B 551/B551M : 2012 : R2017 | Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate |
ASTM B 176 : 2018 | Standard Specification for Copper-Alloy Die Castings |
ASTM B 506 : 2016 | Standard Specification for Copper-Clad Stainless Steel Sheet and Strip for Building Construction |
ASTM B 100 : 2020 | Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates and Sheets for Bridge and Other Structural Use |
ASTM F 1083 : 2018 | Standard Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded, for Fence Structures |
ASTM B 197/B197M : 2020 | Standard Specification for Copper-Beryllium Alloy Wire |
ASTM B 272 : 2012 : R2019 | Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip) |
ASTM F 799 : 2019 | Standard Specification for Cobalt-28 Chromium-6 Molybdenum Alloy Forgings for Surgical Implants (UNS R31537, R31538, R31539) |
ASTM F 3043 : 2015 | Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength |
ASTM F 2384 : 2010 : R2016 | Standard Specification for Wrought Zirconium-2.5Niobium Alloy for Surgical Implant Applications (UNS R60901) |
ASTM B 160 : 2005 : R2019 | Standard Specification for Nickel Rod and Bar |
ASTM B 169/B169M : 2020 | Standard Specification for Aluminum Bronze Sheet, Strip, and Rolled Bar |
ASTM B 335 : 2003 : R2018 | Standard Specification for Nickel-Molybdenum Alloy Rod |
ASTM E 3097 : 2017 | Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys |
ASTM B 819 : 2019 | Standard Specification for Seamless Copper Tube for Medical Gas Systems |
ASTM A 716 : 2018 | Standard Specification for Ductile Iron Culvert Pipe |
ASTM B 280 : 2020 | Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service |
ASTM B 392 : 2018 | Standard Specification for Niobium and Niobium Alloy Bar, Rod, and Wire |
ASTM F 67 : 2013 : R2017 | Standard Specification for Unalloyed Titanium, for Surgical Implant Applications (UNS R50250, UNS R50400, UNS R50550, UNS R50700) |
ASTM F 3001 : 2014 | Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium ELI (Extra Low Interstitial) with Powder Bed Fusion |
ASTM B 121/B121M : 2016 | Standard Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar |
ASTM B 462 : 2018 : EDT 1 | Standard Specification for Forged or Rolled Nickel Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service |
ASTM F 2921 : 2013 : R2019 | Standard Terminology for Additive Manufacturing—Coordinate Systems and Test Methodologies |
ASTM B 1009 : 2020 | Standard Specification for Titanium Alloy Bars for Near Surface Mounts in Civil Structures |
ASTM A 220/A220M : 1999 : R2018 : EDT 1 | Standard Specification for Pearlitic Malleable Iron |
ASTM B 134/B134M : 2015 | Standard Specification for Brass Wire |
ASTM E 3098 : 2017 | Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys |
ASTM B 395/B395M : 2018 | Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes |
ASTM B 969/B969M : 2018 : EDT 1 | Standard Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, and the Semi-Solid Thixocast and Rheocast Casting Processes |
ASTM B 411/B411M : 2014 : R2019 | Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar |
ASTM B 740 : 2009 : R2015 | Standard Specification for Copper-Nickel-Tin Spinodal Alloy Strip |
ASTM E 2472 : 2012 : R2018 : EDT 1 | Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions |
ASTM B 473 : 2007 : R2018 | Standard Specification for UNS N08020, UNS N08024, and UNS N08026 Nickel Alloy Bar and Wire |
ASTM E 606/E606M : 2019 : EDT 1 | Standard Test Method for Strain-Controlled Fatigue Testing |
ASTM B 283/B283M : 2020 | Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed) |
ASTM F 1282 : 2017 | Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe |
ASTM A 229/A229M : 2018 | Standard Specification for Steel Wire, Quenched and Tempered for Mechanical Springs |
ASTM B 359/B359M : 2018 | Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins |
ASTM G 107 : 1995 : R2020 : EDT 1 | Standard Guide for Formats for Collection and Compilation of Corrosion Data for Metals for Computerized Database Input |
ASTM F 3318 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam |
ASTM A 1111 : 2018 | Standard Specification for Cast Iron Closet Flanges for Use With Cast Iron Soil Pipe and Fittings in Gravity Flow Plumbing Drain, Waste, and Vent Sanitary Applications |
ASTM B 988 : 2018 | Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components |
ASTM F 519 : 2018 | Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments |
ASTM E 647 : 2015 : EDT 1 | Standard Test Method for Measurement of Fatigue Crack Growth Rates |
ASTM B 643 : 2018 | Standard Specification for Copper-Beryllium Alloy Seamless Tube |
ASTM E 2899 : 2019 : EDT 1 | Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending |
ASTM F 855 : 2020 | Standard Specifications for Temporary Protective Grounds to Be Used on De-energized Electric Power Lines and Equipment |
ASTM B 967/B967M : 2018 | Standard Specification for Copper-Zinc-Tin-Bismuth Alloy Rod, Bar and Wire |
ASTM B 162 : 1999 : R2019 | Standard Specification for Nickel Plate, Sheet, and Strip |
ASTM B 929 : 2017 | Standard Specification for Copper-Nickel-Tin Spinodal Alloy Rod and Bar |
ASTM F 3184 : 2016 | Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion |
ASTM E 139 : 2011 : R2018 | Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials |
ASTM B 164 : 2003 : R2019 | Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire |
ASTM B 672 : 2002 : R2018 | Standard Specification for Nickel-Iron-Chromium-Molybdenum-Columbium Stabilized Alloy (UNS N08700) Bar and Wire (Withdrawn 2023) |
ASTM F 1537 : 2020 | Standard Specification for Wrought Cobalt-28Chromium-6Molybdenum Alloys for Surgical Implants (UNS R31537, UNS R31538, and UNS R31539) |
ASTM B 637 : 2018 | Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service |
ASTM B 534 : 2020 | Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM C 1671 : 2020 : REV A | Standard Practice for Qualification and Acceptance of Boron Based Metallic Neutron Absorbers for Nuclear Criticality Control for Dry Cask Storage Systems and Transportation Packaging |
ASTM A 1058 : 2019 | Standard Test Methods for Mechanical Testing of Steel Products—Metric |
ASTM B 441 : 2016 | Standard Specification for Copper-Cobalt-Beryllium, Copper-Nickel-Beryllium, and Copper-Nickel-Lead-Beryllium Rod and Bar (UNS Nos. C17500, C17510, and C17465) |
ASTM B 824 : 2017 | Standard Specification for General Requirements for Copper Alloy Castings |
ASTM E 2207 : 2015 | Standard Practice for Strain-Controlled Axial-Torsional Fatigue Testing with Thin-Walled Tubular Specimens |
ASTM F 2257 : 2014 | Standard Specification for Wrought Seamless or Welded and Drawn 18 Chromium-14Nickel-2.5Molybdenum Stainless Steel Small Diameter Tubing for Surgical Implants (UNS S31673) |
ASTM E 1221 : 2012 : REV A : R2018 : EDT 1 | Standard Test Method for Determining Plane-Strain Crack-Arrest Fracture Toughness, <emph type="bdit">K<inf>Ia</inf></emph>, of Ferritic Steels |
ASTM B 167 : 2018 | Standard Specification for Nickel-Chromium-Aluminum Alloys (UNS N06699), Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674), and Nickel-Chromium-Molybdenum-Copper Alloy (UNS N06235) Seamless Pipe and Tube |
ASTM B 16/B16M : 2019 | Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines |
ASTM F 1813 : 2013 | Standard Specification for Wrought Titanium<span class='unicode'>–</span>12 Molybdenum<span class='unicode'>–</span>6 Zirconium<span class='unicode'>–</span>2 Iron Alloy for Surgical Implant (UNS R58120) |
ASTM F 2989 : 2013 | Standard Specification for Metal Injection Molded Unalloyed Titanium Components for Surgical Implant Applications |
ASTM B 122/B122M : 2020 | Standard Specification for Copper-Nickel-Tin Alloy, Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 103/B103M : 2019 | Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar |
ASTM F 3122 : 2014 | Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes |
ASTM F 2516 : 2018 | Standard Test Method for Tension Testing of Nickel-Titanium Superelastic Materials |
ASTM E 1304 : 1997 : R2020 | Standard Test Method for Plane-Strain (Chevron-Notch) Fracture Toughness of Metallic Materials |
ASTM B 188 : 2015 : EDT 1 | Standard Specification for Seamless Copper Bus Pipe and Tube |
ASTM B 352/B352M : 2017 | Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application |
ASTM F 3055 : 2014 : REV A | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N07718) with Powder Bed Fusion |
ASTM B 42 : 2020 | Standard Specification for Seamless Copper Pipe, Standard Sizes |
ASTM A 494/A494M : 2018 : REV A | Standard Specification for Castings, Nickel and Nickel Alloy |
ASTM A 823 : 1999 : R2019 | Standard Specification for Statically Cast Permanent Mold Gray Iron Castings |
ASTM B 564 : 2019 | Standard Specification for Nickel Alloy Forgings |
ASTM E 1681 : 2003 : R2020 | Standard Test Method for Determining Threshold Stress Intensity Factor for Environment-Assisted Cracking of Metallic Materials |
ASTM B 493/B493M : 2014 : R2019 | Standard Specification for Zirconium and Zirconium Alloy Forgings |
ASTM B 870 : 2008 : R2014 | Standard Specification for Copper-Beryllium Alloy Forgings and Extrusions Alloys (UNS Nos. C17500 and C17510) |
ASTM B 805 : 2006 : R2017 : EDT 1 | Standard Specification for Precipitation Hardening Nickel Alloys Bar and Wire |
ASTM B 19 : 2020 | Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks |
ASTM B 370 : 2012 : R2019 | Standard Specification for Copper Sheet and Strip for Building Construction |
ASTM A 874/A874M : 1998 : R2018 : EDT 1 | Standard Specification for Ferritic Ductile Iron Castings Suitable for Low-Temperature Service |
ASTM B 98/B98M : 2013 : R2019 | Standard Specification for Copper-Silicon Alloy Rod, Bar and Shapes |
ASTM A 536 : 1984 : R2019 : EDT 1 | Standard Specification for Ductile Iron Castings |
ASTM A 278/A278M : 2001 : R2020 | Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650 °F (350 °C) |
ASTM B 684/B684M : 2016 | Standard Specification for Platinum-Iridium Electrical Contact Materials |
ASTM B 775/B775M : 2019 | Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe |
ASTM E 1450 : 2016 | Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium |
ASTM E 292 : 2018 | Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials |
ASTM B 505/B505M : 2018 | Standard Specification for Copper Alloy Continuous Castings |
ASTM B 574 : 2018 | Standard Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod |
ASTM B 30 : 2020 | Standard Specification for Copper Alloys in Ingot and Other Remelt Forms |
ASTM E 185 : 2016 | Standard Practice for Design of Surveillance Programs for Light-Water Moderated Nuclear Power Reactor Vessels |
ASTM F 560 : 2017 | Standard Specification for Unalloyed Tantalum for Surgical Implant Applications (UNS R05200, UNS R05400) |
ASTM B 523/B523M : 2018 | Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Tubes |
ASTM E 517 : 2019 | Standard Test Method for Plastic Strain Ratio <emph type="bdit">r</emph> for Sheet Metal |
ASTM F 1091 : 2020 | Standard Specification for Wrought Cobalt-20Chromium-15Tungsten-10Nickel Alloy Surgical Fixation Wire (UNS R30605) |
ASTM B 834 : 2017 | Standard Specification for Pressure Consolidated Powder Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS N08367), Nickel-Chromium-Molybdenum-Columbium (Nb) (UNS N06625), Nickel-Chromium-Iron Alloys (UNS N06600 and N06690), and Nickel-Chromium-Iron-Columbium-Molybdenum (UNS N07718) Alloy Pipe Flanges, Fittings, Valves, and Parts |
ASTM E 21 : 2020 | Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials |
ASTM B 541 : 2001 : R2018 | Standard Specification for Gold Electrical Contact Alloy |
ASTM B 467 : 2014 | Standard Specification for Welded Copper-Nickel Pipe |
ASTM B 62 : 2017 | Standard Specification for Composition Bronze or Ounce Metal Castings |
ASTM B 427 : 2009 : R2015 | Standard Specification for Gear Bronze Alloy Castings |
ASTM B 587 : 2019 | Standard Specification for Welded Brass Tube |
ASTM A 473 : 2019 | Standard Specification for Stainless Steel Forgings |
ASTM E 488/E488M : 2018 | Standard Test Methods for Strength of Anchors in Concrete Elements |
ASTM B 148 : 2018 | Standard Specification for Aluminum-Bronze Sand Castings |
ASTM B 927/B927M : 2017 | Standard Specification for Brass Rod, Bar, and Shapes |
ASTM B 163 : 2019 | Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes |
ASTM A 834 : 1995 : R2020 | Standard Specification for Common Requirements for Iron Castings for General Industrial Use |
ASTM B 152/B152M : 2019 | Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar |
ASTM B 306 : 2020 | Standard Specification for Copper Drainage Tube (DWV) |
ASTM A 1109 : 2018 | Standard Specification for Special Fittings for Single-Stack Hubless Cast Iron Soil Pipe Fittings for Sanitary, Waste, and Vent Piping Applications |
ASTM B 608 : 2018 | Standard Specification for Welded Copper-Alloy Pipe |
ASTM B 101 : 2012 : R2019 | Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction |
ASTM E 2818 : 2011(R2019) | Standard Practice for Determination of Quasistatic Fracture Toughness of Welds |
ASTM B 829 : 2019 : REV A | Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube |
ASTM E 3205 : 2020 | Standard Test Method for Small Punch Testing of Metallic Materials |
ASTM B 248 : 2017 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 251/B251M : 2017 | Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube |
ASTM B 777 : 2015 : R2020 | Standard Specification for Tungsten Base, High-Density Metal |
ASTM F 90 : 2014 | Standard Specification for Wrought Cobalt-20Chromium-15Tungsten-10Nickel Alloy for Surgical Implant Applications (UNS R30605) |
ASTM F 468 : 2016 | Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use |
ASTM B 22/B22M : 2017 | Standard Specification for Bronze Castings for Bridges and Turntables |
ASTM B 694 : 2019 | Standard Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding |
ASTM A 74 : 2020 | Standard Specification for Cast Iron Soil Pipe and Fittings |
ASTM B 592 : 2020 | Standard Specification for Copper-Zinc-Aluminum-Cobalt Alloy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 466/B466M : 2018 | Standard Specification for Seamless Copper-Nickel Pipe and Tube |
ASTM B 447 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube |
ASTM F 2146 : 2013 | Standard Specification for Wrought Titanium-3Aluminum-2.5Vanadium Alloy Seamless Tubing for Surgical Implant Applications (UNS R56320) |
ASTM F 562 : 2013 | Standard Specification for Wrought 35Cobalt-35Nickel-20Chromium-10Molybdenum Alloy for Surgical Implant Applications (UNS R30035) |
ASTM B 751 : 2020 | Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Tube |
ASTM A 476/A476M : 2000 : R2018 | Standard Specification for Ductile Iron Castings for Paper Mill Dryer Rolls |
ASTM B 543/B543M : 2018 | Standard Specification for Welded Copper and Copper-Alloy Heat Exchanger Tube |
ASTM B 768 : 2011 : R2016 | Standard Specification for Copper-Cobalt-Beryllium Alloy and Copper-Nickel-Beryllium Alloy Strip and Sheet |
ASTM B 569 : 2019 | Standard Specification for Brass Strip in Narrow Widths and Light Gage for Heat-Exchanger Tubing |
ASTM B 96/B96M : 2020 | Standard Specification for Copper-Silicon Alloy Plate, Sheet, Strip, and Rolled Bar for General Purposes and Pressure Vessels |
ASTM B 690 : 2018 | Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08367) Seamless Pipe and Tube |
ASTM F 136 : 2013 | Standard Specification for Wrought Titanium-6Aluminum-4Vanadium ELI (Extra Low Interstitial) Alloy for Surgical Implant Applications (UNS R56401) |
ASTM F 2229 : 2021 | Standard Specification for Wrought, Nitrogen Strengthened 23Manganese-21Chromium-1Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29108) |
ASTM B 903 : 2015 | Standard Specification for Seamless Copper Heat Exchanger Tubes With Internal Enhancement |
ASTM B 552 : 2019 | Standard Specification for Seamless and Welded Copper–Nickel Tubes for Water Desalting Plants |
ASTM A 232/A232M : 2018 | Standard Specification for Chromium-Vanadium Alloy Steel Valve Spring Quality Wire |
ASTM B 688 : 2018 | Standard Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08367) Plate, Sheet, and Strip |
ASTM B 709 : 2017 | Standard Specification for Iron-Nickel-Chromium-Molybdenum Alloy (UNS N08028) Plate, Sheet, and Strip |
ASTM F 688 : 2019 | Standard Specification for Wrought Cobalt-35Nickel-20Chromium-10Molybdenum Alloy Plate, Sheet, and Foil for Surgical Implants (UNS R30035) |
ASTM E 2215 : 2019 | Standard Practice for Evaluation of Surveillance Capsules from Light-Water Moderated Nuclear Power Reactor Vessels |
ASTM B 465 : 2020 | Standard Specification for Copper-Iron Alloy Plate, Sheet, Strip, and Rolled Bar |
ASTM B 351/B351M : 2013 : R2018 | Standard Specification for Hot-Rolled and Cold-Finished Zirconium and Zirconium Alloy Bars, Rod, and Wire for Nuclear Application |
ASTM F 3046 : 2013 | Standard Specification for Wrought Titanium-3Aluminum-2.5Vanadium Alloy for Surgical Implant Applications (UNS R56320) |
ASTM C 1187 : 2020 : REV A | Standard Guide for Establishing Surveillance Test Program for Boron-based Neutron Absorbing Material Systems for Use in Nuclear Fuel Storage Racks in Pool Environment |
ASTM B 196/B196M : 2018 | Standard Specification for Copper-Beryllium Alloy Rod and Bar |
ASTM A 197/A197M : 2000 : R2019 | Standard Specification for Cupola Malleable Iron |
ASTM B 640 : 2012 : REV A : R2021 | Standard Specification for Welded Copper Tube for Air Conditioning and Refrigeration Service |
ASTM B 743 : 2012 : R2020 | Standard Specification for Seamless Copper Tube in Coils |
ASTM B 86 : 2018 | Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloy Foundry and Die Castings |
ASTM F 75 : 2018 | Standard Specification for Cobalt-28 Chromium-6 Molybdenum Alloy Castings and Casting Alloy for Surgical Implants (UNS R30075) |
ASTM B 950 : 2021 | Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys |
ASTM A 370 : 2020 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products |
ASTM G 111 : 1997 : R2018 | Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both |
ASTM F 620 : 2020 | Standard Specification for Titanium Alloy Forgings for Surgical Implants in the Alpha Plus Beta Condition |
ASTM B 139/B139M : 2012 : R2017 | Standard Specification for Phosphor Bronze Rod, Bar, and Shapes |
ASTM B 1005 : 2017 | Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar) |
ASTM F 3160 : 2016 | Standard Guide for Metallurgical Characterization of Absorbable Metallic Materials for Medical Implants |
ASTM B 206/B206M : 2012 : R2017 | Standard Specification for Copper-Nickel-Zinc (Nickel Silver) Wire and Copper-Nickel Alloy Wire |
ASTM F 1044 : 2005 : R2017 : EDT 1 | Standard Test Method for Shear Testing of Calcium Phosphate Coatings and Metallic Coatings |
ASTM B 171/B171M : 2018 | Standard Specification for Copper-Alloy Plate and Sheet for Pressure Vessels, Condensers, and Heat Exchangers |
ASTM B 658/B658M : 2011 : R2020 | Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe |
ASTM B 1007 : 2017 | Standard Specification for Welded Precipitation Hardenable or Cold Worked, Nickel Alloy Tube |
ASTM B 1014 : 2020 | Standard Specification for Welded Copper and Copper Alloy Condenser and Heat Exchanger Tubes with a Textured Surface(s) |
ASTM F 139 : 2019 | Standard Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Sheet and Strip for Surgical Implants (UNS S31673) |
ASTM B 68/B68M : 2019 | Standard Specification for Seamless Copper Tube, Bright Annealed |
ASTM B 248M : 2017 | Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric) |
ASTM A 842 : 2011 : REV A : R2018 : EDT 1 | Standard Specification for Compacted Graphite Iron Castings |
ASTM B 837 : 2019 | Standard Specification for Seamless Copper Tube for Natural Gas and Liquified Petroleum (LP) Gas Fuel Distribution Systems |
ASTM A 395/A395M : 1999 : R2018 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
ASTM B 888/B888M : 2019 | Standard Specification for Copper Alloy Strip for Use in Manufacture of Electrical Connectors or Spring Contacts |
ASTM F 2885 : 2017 | Standard Specification for Metal Injection Molded Titanium-6Aluminum-4Vanadium Components for Surgical Implant Applications |
ASTM F 3056 : 2014 : EDT 1 | Standard Specification for Additive Manufacturing Nickel Alloy (UNS N06625) with Powder Bed Fusion |
ASTM F 2063 : 2018 | Standard Specification for Wrought Nickel-Titanium Shape Memory Alloys for Medical Devices and Surgical Implants |
ASTM B 446 : 2019 | Standard Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650) Rod and Bar |
ASTM F 1940 : 2007 : REV A : R2019 | Standard Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners |
ASTM A 1000/A1000M : 2017 | Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality |
ASTM F 1043 : 2018 | Standard Specification for Strength and Protective Coatings on Steel Industrial Fence Framework |
ASTM E 468 : 2018 | Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials |
ASTM B 639 : 2002 : R2018 | Standard Specification for Precipitation Hardening Cobalt-Containing Alloys (UNS R30155 and UNS R30816) Rod, Bar, Forgings, and Forging Stock for High-Temperature Service |
ASTM B 944 : 2011 : R2016 | Standard Specification for Copper-Beryllium Welded Heat Exchanger and Condenser Tube (UNS No. C17510) |
ASTM F 3273 : 2017 | Standard Specification for Wrought Molybdenum-47.5 Rhenium Alloy for Surgical Implants (UNS R03700) |
ASTM B 48 : 2000 : R2016 | Standard Specification for Soft Rectangular and Square Bare Copper Wire for Electrical Conductors |
ASTM F 3213 : 2017 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Cobalt-28 Chromium-6 Molybdenum via Powder Bed Fusion |
ASTM B 36/B36M : 2018 | Standard Specification for Brass Plate, Sheet, Strip, And Rolled Bar |
ASTM A 608/A608M : 2020 | Standard Specification for Centrifugally Cast Iron-Chromium-Nickel High-Alloy Tubing for Pressure Application at High Temperatures |
ASTM B 956 : 2019 : EDT 1 | Standard Specification for Welded Copper and Copper-Alloy Condenser and Heat Exchanger Tubes with Integral Fins |
ASTM B 21/B21M : 2020 | Standard Specification for Naval Brass Rod, Bar, and Shapes |
ASTM B 906 : 2019 | Standard Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip |
ASTM E 143 : 2020 | Standard Test Method for Shear Modulus at Room Temperature |
ASTM F 138 : 2019 | Standard Specification for Wrought 18Chromium-14Nickel-2.5Molybdenum Stainless Steel Bar and Wire for Surgical Implants (UNS S31673) |
ASTM B 919 : 2019 | Standard Specification for Welded Copper Heat Exchanger Tubes With Internal Enhancement |
ASTM F 1058 : 2016 | Standard Specification for Wrought 40Cobalt-20Chromium-16Iron-15Nickel-7Molybdenum Alloy Wire, Strip, and Strip Bar for Surgical Implant Applications (UNS R30003 and UNS R30008) |
ASTM F 1314 : 2018 | Standard Specification for Wrought Nitrogen Strengthened 22 Chromium–13 Nickel–5 Manganese–2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910) |
ASTM B 301/B301M : 2013 : R2020 | Standard Specification for Free-Cutting Copper Rod, Bar, Wire, and Shapes |
ASTM B 302 : 2017 | Standard Specification for Threadless Copper Pipe, Standard Sizes |
ASTM B 140/B140M : 2012 : R2017 | Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes |
ASTM B 315 : 2019 | Standard Specification for Seamless Copper Alloy Pipe and Tube |
ASTM G 143 : 2003 : R2018 | Standard Test Method for Measurement of Web/Roller Friction Characteristics |
ASTM E 740/E740M : 2003 : R2016 | Standard Practice for Fracture Testing with Surface-Crack Tension Specimens |
ASTM F 3302 : 2018 | Standard for Additive Manufacturing – Finished Part Properties – Standard Specification for Titanium Alloys via Powder Bed Fusion |
ASTM A 126 : 2004 : R2019 | Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings |
ASTM B 986 : 2013 : R2019 | Standard Test Method for Determination of Tensile Strength by Mass Method for Stranded Conductors Intended for use in Electronic Application |
ASTM B 75/B75M : 2020 | Standard Specification for Seamless Copper Tube |
ASTM F 3346 : 2019 | Standard Specification for Polyethylene of Raised Temperature/Aluminum/Polyethylene of Raised Temperature (PERT/AL/PE-RT) Composite Pressure Pipe |
ASTM F 606/F606M : 2019 | Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets |
ASTM B 130 : 2019 | Standard Specification for Commercial Bronze Strip for Bullet Jackets |
ASTM B 138/B138M : 2011 : R2017 | Standard Specification for Manganese Bronze Rod, Bar, and Shapes |
ASTM A 1056 : 2020 | Standard Specification for Cast Iron Couplings Used for Joining Hubless Cast Iron Soil Pipe and Fittings |
ASTM A 47/A47M : 1999 : R2018 : EDT 1 | Standard Specification for Ferritic Malleable Iron Castings |
ASTM E 1820 : 2020 : REV B | Standard Test Method for Measurement of Fracture Toughness |
ASTM F 961 : 2020 | Standard Specification for 35Cobalt-35Nickel-20Chromium-10Molybdenum Alloy Forgings for Surgical Implants (UNS R30035) |
ASTM E 1921 : 2020 | Standard Test Method for Determination of Reference Temperature, <emph type="bdit">T<inf >o</inf></emph>, for Ferritic Steels in the Transition Range |
ASTM A 746 : 2018 | Standard Specification for Ductile Iron Gravity Sewer Pipe |
ASTM B 111/B111M : 2018 : REV A | Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock |
ASTM B 655/B655M : 2010 : R2018 | Standard Specification for Niobium-Hafnium Alloy Bar and Wire |
ASTM B 776 : 2012 : R2019 | Standard Specification for Hafnium and Hafnium Alloy Strip, Sheet, and Plate |
ASTM G 49 : 1985 : R2019 | Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens |
ASTM E 83 : 2000 : EDT 1 | Standard Practice for Verification and Classification of Extensometer |
AS ISO/ASTM 52921:2020 | Standard terminology for additive manufacturing - Coordinate systems and test methodologies |
ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
AS ISO/ASTM 52910:2020 | Additive manufacturing - Design - Requirements, guidelines and recommendations |
ASTM E 1012 : 2014 : EDT 1 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
ASTM B 557M : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric] |
ASTM B 557 : 1994 | Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products |
ASTM E 1012 : 2019 | Standard Practice for Verification of Testing Frame and Specimen Alignment Under Tensile and Compressive Axial Force Application |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.