ASTM F 1200 : 1988 : R2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150°F)
Hardcopy , PDF
01-07-2021
English
15-09-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 01.07, 2017 Defines welded strainers in services above 150 psig or 150 degrees F (1 MPa and 65 degrees C).
| Committee |
F 25
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 2016
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers welded strainers in services above 150 psig or 150°F (1 MPa and 65°C). For welded strainers in services at or below these ratings and cast strainers, see Specification F1199.
1.2This specification provides the minimum requirements for the design fabrication, rating, marking, and testing of welded pipe line strainers for services above 0°F (−18°C).
1.3Strainers manufactured to this specification are acceptable for use in the marine environment.
1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 1199 : 1988 : R2015 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| ASTM F 1199 : 1988 : R1998 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| ASME B16.15 : 2013 | CAST COPPER ALLOY THREADED FITTINGS: CLASSES 125 AND 250 |
| ASTM D 93 : 1990 : EDT 1 | Standard Test Methods for Flash Point by Pensky-Martens Closed Tester |
| MSS SP 63 : LATEST | HIGH STRENGTH WROUGHT WELDING FITTINGS |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| MSS SP 51 : 2012 | CLASS 150LW CORROSION RESISTANT FLANGES AND CAST FLANGED FITTINGS |
| ASTM F 1199 : 1988 : R2010 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ANSI B2.1 : LATEST | PIPE THREADS (EXCEPT DRYSEAL) |
| ASTM F 1199 : 1988 : R2019 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASTM D 93 : 2000 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASME B16.4 : 2016 | GRAY IRON THREADED FITTINGS: CLASSES 125 AND 250 |
| ASTM D 93 : 1985 | Standard Test Method for Flash Point by Pensky-Martens Closed Tester |
| ASTM D 93 : 1997 | Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester |
| ASTM F 1199 : 1988 : R2015 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ASME B16.25 : 2012 | BUTTWELDING ENDS |
| ASTM F 1199 : 1988 : R2004 | Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum) |
| ASME B16.3 : 2016 | MALLEABLE IRON THREADED FITTINGS: CLASSES 150 AND 300 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.