ASTM F 2896 : 2011 : R2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids
Available format(s)
Hardcopy , PDF
Superseded date
25-08-2023
Superseded by
Language(s)
English
Published date
07-09-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
9
|
| ProductNote |
Reconfirmed 2017
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers requirements and test methods for materials, dimensions, workmanship, and markings for on-site manufactured multilayer reinforced polyethylene composite pipe. It covers nominal sizes 6 in. through 36 in. (150 mm through 915 mm). These multilayered reinforced polyethylene composite pipe products2 are assembled and installed in various lengths, including long continuous lengths. These products are intended for the transport of crude oil, natural gas and hazardous liquids in the rehabilitation of existing pipelines and for new pipelines.
Note 1:Hazardous liquids are those liquids defined by the U.S. Department of Transportation in 49 CFR 195.2.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2837 : 2013 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM F 585 : 2016 : R2021 | Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers |
| ASTM D 1600 : 1999 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 5035 : 1995 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM F 1606 : 2005 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
| ASTM D 2774 : 2004 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM F 1606 : 1995 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner (Withdrawn 2004) |
| ASTM D 1693 : 2000 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM A 312/A312M : 2021 | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
| ASTM F 1606 : 2019 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
| ASTM D 1598 : 2002 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2006 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2774 : 2021 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2122 : 1998 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM F 585 : 2016 | Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers |
| ASTM D 2513 : 2016 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1249 : 2006 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 1598 : 2015 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2774 : 2012 : REDLINE | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM F 412 : 2020 : REV A | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 1598 : 2015 : REV A | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2774 : 2021 : REV A | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2513 : 2003 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 412 : 2021 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 2513 : 2012 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1000 : 2017 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2837 : 2001 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2513 : 2008 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2992 : 2022 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM A 312/A312M : 2022 | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
| ASTM F 2620 : 2014-01 | PRACTICE FOR HEAT FUSION JOINING OF POLYETHYLENE PIPE AND FITTINGS |
| ASTM D 2513 : 2011 : REV B | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2620 : 2011 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 2620 : 2020 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2256/D2256M : 2010 : R2015 | Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method |
| ASTM D 2513 : 2009 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2004 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 1987 | Standard Specification for Thermoplastic Gas Pressure Piping Systems |
| ASTM D 3850 : 1994 : R2006 | Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA) |
| ASTM D 2992 : 2001 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM F 2620 : 2011 : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2513 : 2011 : REV C | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1249 : 1994 : REV B | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM F 1668 : 2008 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM A 312/A312M : 2019 | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
| ASTM D 2774 : 2001 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 1598 : 2023 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM F 2620 : 2019 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM F 2620 : 2020 : REV A : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2837 : 2002 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2001 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 1693 : 2008 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2513 : 2016 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2004 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2513 : 2013 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 3850 : 2019 | Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA) |
| ASTM D 2837 : 2021 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2513 : 1999 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2009 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2774 : 1994 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 3850 : 2012 | Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA) |
| ASTM F 2620 : 2013 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 1600 : 2007 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2003 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 5035 : 2011 : R2015 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 1600 : 2013 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2513 : 2001 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1693 : 2015 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1693 : 2012 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1693 : 1994 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM A 519 : 1996 | Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing |
| ASTM D 2513 : 2001 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2014 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 2837 : 2008 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 1998 : REV A | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM F 585 : 2016 : REDLINE | Standard Guide for Insertion of Flexible Polyethylene Pipe Into Existing Sewers |
| API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| ASTM D 2774 : 2020 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2513 : 2001 : REV A : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1600 : 2008 | Standard Terminology for Abbreviated Terms Relating to Plastics |
| ASTM D 1598 : 1997 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2513 : 2011 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2774 : 2008 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM D 2513 : 2014 : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2001 : REV A : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials |
| ASTM D 2837 : 2011 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 1599 : 2014 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2014 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1693 : 2021 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1599 : 2014 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1000 : 2004 : EDT 1 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2513 : 2000 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2007 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1000 : 2010 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2513 : 2019 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2122 : 1998 : EDT 1 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2008 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 2256/D2256M : 2021 | Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method |
| ASTM D 2513 : 2003 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1249 : 2006 : R2011 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2837 : 2022 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM F 1668 : 2016 : R2022 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM D 1599 : 1999 : R2011 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 1693 : 2005 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM F 2620 : 2012 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM F 2620 : 2006 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 1599 : 1999 : EDT 1 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2006 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2619/F2619M : 2013 : REDLINE | Standard Specification for High-Density Polyethylene (PE) Line Pipe |
| ASTM D 5035 : 2011 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM D 2122 : 2022 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1600 : 2018 | Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
| ASTM D 2992 : 2006 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 5035 : 2006 : R2008 : EDT 1 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 1598 : 2021 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2007 : REV B : EDT 1 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1000 : 2009 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2513 : 2008 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1598 : 2002 : R2008 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASTM D 1693 : 2007 : REV A | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2513 : 2018 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 2620 : 2020 : REV A | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2122 : 1998 : R2004 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2122 : 2016 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2774 : 2012 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| CFR 49(PTS178-199) : OCT 2017 | TRANSPORTATION |
| ASTM F 1249 : 1990 : R1995 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 2992 : 1996 : EDT 1 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 3850 : 1994 : R2000 | Standard Test Method for Rapid Thermal Degradation of Solid Electrical Insulating Materials By Thermogravimetric Method (TGA) |
| ASTM F 1606 : 2005 : R2014 | Standard Practice for Rehabilitation of Existing Sewers and Conduits with Deformed Polyethylene (PE) Liner |
| ASTM D 1599 : 1999 : R2005 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 1668 : 2016 : REDLINE | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM D 1598 : 2002 : R2009 | Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure |
| ASTM D 5035 : 2006 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM A 312/A312M : 2022 : REV A | Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes |
| ASTM A 312/A312M : 2017-03 | SPECIFICATION FOR SEAMLESS, WELDED, AND HEAVILY COLD WORKED AUSTENITIC STAINLESS STEEL PIPES |
| ASTM D 1693 : 2015 : EDT 1 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1000 : 1999 | Standard Test Method for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2513 : 2007 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1000 : 2004 | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM F 1668 : 1996 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM F 2620 : 2020 : REV A : EDT 2 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 1693 : 2001 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2513 : 2007 : REV B | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1693 : 2013 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 1000 : 2017 : REDLINE | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| ASTM D 2992 : 2012 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 2513 : 2012 : REV A : EDT 1 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2774 : 2004 : EDT 1 | Standard Practice for Underground Installation of Thermoplastic Pressure Piping |
| ASTM F 1668 : 2016 | Standard Guide for Construction Procedures for Buried Plastic Pipe |
| ASTM D 2122 : 1998 : R2010 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2513 : 2018 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2011 : REV A | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2513 : 2012 | Standard Specification for Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 2992 : 2018 | Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 1599 : 1999 | Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings |
| ASTM F 1249 : 2013 : REDLINE | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 5035 : 2011 : R2019 | Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method) |
| ASTM F 2620 : 2009 : EDT 1 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
| ASTM D 2513 : 2004 : REV A | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM F 1249 : 2001 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 2122 : 2015 | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM F 1249 : 2013 | Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
| ASTM D 2513 : 2005 | Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings |
| ASTM D 1693 : 2007 | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
| ASTM D 2837 : 2013 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
| ASTM D 2837 : 2004 : EDT 1 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.