ASTM F 1249 : 2013 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
12-08-2020
English
01-10-2013
CONTAINED IN VOL. 15.09, 2015 Specifies the rate of water vapor transmission through flexible barrier materials.
| Committee |
F 02
|
| DocumentType |
Redline
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1This test method covers a procedure for determining the rate of water vapor transmission through flexible barrier materials. The method is applicable to sheets and films up to 3 mm (0.1 in.) in thickness, consisting of single or multilayer synthetic or natural polymers and foils, including coated materials. It provides for the determination of (1) water vapor transmission rate (WVTR), (2) the permeance of the film to water vapor, and (3) for homogeneous materials, water vapor permeability coefficient.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-PRF-22191 Revision F:2008 | Barrier Materials, Transparent, Flexible, Heat-Sealable |
| S.R. CEN ISO/TS 16775:2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 (ISO/TS 16775:2014) |
| CAN/CSA-ISO/TS 16775:17 | Packaging for terminally sterilized medical devices — Guidance on the application of ISO 11607-1 and ISO 11607-2 (Adopted ISO technical specification 16775:2014, first edition, 2014-05-15) |
| ASTM F 2097 : 2016 : REDLINE | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM F 1770 : 1997 : EDT 1 | Standard Test Method for Evaluation of Solubility, Diffusivity, and Permeability of Flexible Barrier Materials to Water Vapor (Withdrawn 2004) |
| ASTM D 2103 : 2015 : REDLINE | Standard Specification for Polyethylene Film and Sheeting |
| CEN ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices - Guidance on the application of ISO 11607-1 and ISO 11607-2 (ISO/TS 16775:2014) |
| IPC J STD 033 RUSSIAN : B | HANDLING, PACKING, SHIPPING AND USE OF MOISTURE/REFLOW SENSITIVE SURFACE MOUNT DEVICES |
| IPC AJ 820 : A | ASSEMBLY AND JOINING HANDBOOK |
| IPC J STD 033 CHINESE : B-1 | HANDLING, PACKING, SHIPPING AND USE OF MOISTURE/REFLOW SENSITIVE SURFACE MOUNT DEVICES |
| IPC HDBK 850 : 0 | GUIDELINES FOR DESIGN, SELECTION AND APPLICATION OF POTTING MATERIALS AND ENCAPSULATION PROCESSES USED FOR ELECTRONICS PRINTED CIRCUIT BOARD ASSEMBLY |
| IPC HDBK 830 : A | GUIDELINES FOR DESIGN, SELECTION AND APPLICATION OF CONFORMAL COATINGS |
| IPC J STD 033 GERMAN : C | HANDLING, PACKING, SHIPPING, AND USE OF MOISTURE/REFLOW AND/OR PROCESS SENSITIVE COMPONENTS |
| IPC J STD 033 ITALIAN : B | HANDLING, PACKING, SHIPPING AND USE OF MOISTURE/REFLOW SENSITIVE SURFACE MOUNT DEVICES |
| MIL-PRF-32380 Base Document:2011 | BAGS - UNIT PACK BARRIER, CHEMICAL, BIOLOGICAL PROTECTIVE CLOTHING AND ACCESSORIES |
| ASTM D 7407 : 2007 | Standard Guide for Determining The Transmission of Gases Through Geomembranes |
| PD CEN ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices. Guidance on the application of ISO 11607-1 and ISO 11607-2 |
| 17/30352674 DC : 0 | BS IEC 62788-6-2 - MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - PART 6-2: GENERAL TESTS - MOISTURE PERMEATION TESTING WITH POLYMERIC FILMS |
| ASTM C 1775 : 2014 : REDLINE | Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications |
| MIL-PRF-81705 Revision E:2009 | Barrier Materials, Flexible, Electrostatic Discharge Protective, Heat-Sealable |
| ASTM F 2150 : 2013 : REDLINE | Standard Guide for Characterization and Testing of Biomaterial Scaffolds Used in Tissue-Engineered Medical Products |
| ASTM C 1767M : 2016-03 | SPECIFICATION FOR STAINLESS STEEL JACKETING FOR INSULATION |
| ASTM D 7407 : 2007 : R2012 | Standard Guide for Determining The Transmission of Gases Through Geomembranes |
| ASTM E 398 : 2013 : REDLINE | Standard Test Method for Water Vapor Transmission Rate of Sheet Materials Using Dynamic Relative Humidity Measurement |
| ASTM F 2896 : 2011 : R2017 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM E 154/E154M : 2008 : REV A : R2013 : EDT 1 | Standard Test Methods for Water Vapor Retarders Used in Contact with Earth Under Concrete Slabs, on Walls, or as Ground Cover |
| MIL-PRF-32004 Revision B:2003 | PACKAGING OF FOOD IN POLYMERIC TRAYS |
| MIL B 29597 : (1) | BAG, ODOR BARRIER, FLEXIBLE (FOR FOOD CONTAMINATED PLASTIC WASTE) |
| ASTM C 1423 : 2016 : REDLINE | Standard Guide for Selecting Jacketing Materials for Thermal Insulation |
| ANSI/AAMI/ISO TIR16775:2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 |
| ASTM C 1729M : 2017 : REDLINE | Standard Specification for Aluminum Jacketing for Insulation |
| ISO/TS 16775:2014 | Packaging for terminally sterilized medical devices Guidance on the application of ISO 11607-1 and ISO 11607-2 |
| UNI CEN ISO/TS 16775 : 2014 | PACKAGING FOR TERMINALLY STERILIZED MEDICAL DEVICES - GUIDANCE ON THE APPLICATION OF ISO 11607-1 AND ISO 11607-2 |
| A-A-1728 Revision A:1981 | BAG, PLASTIC (BREAD) |
| MIL-PRF-23199-1 Revision B:2010 | PACKAGING, PACKING AND MARKING (PP&M) REQUIREMENTS FOR INSTRUMENTATION AND CONTROL EQUIPMENT |
| MIL-PRF-131 Revision K:2005 | BARRIER MATERIALS, WATERVAPORPROOF, GREASEPROOF, FLEXIBLE, HEAT-SEALABLE |
| A-A-148 Revision B:1991 | BAG PLASTIC (SANDWICH) |
| ASTM D 4635 : 2016 : REDLINE | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 6577 : 2015 : REDLINE | Standard Guide for Testing Industrial Protective Coatings |
| ASTM D 6701 : 2016 | Standard Test Method for Determining Water Vapor Transmission Rates Through Nonwoven and Plastic Barriers |
| ASTM F 2896 : 2011 | Standard Specification for Reinforced Polyethylene Composite Pipe For The Transport Of Oil And Gas And Hazardous Liquids |
| ASTM C 1729 : 2017 : REDLINE | Standard Specification for Aluminum Jacketing for Insulation |
| ASTM E 1745 : 2017 : REDLINE | Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs |
| ASTM E 96/E96M : 2016 : REDLINE | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM E 177 : 2014 : REDLINE | Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods |
| ASTM E 104 : 2002 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
Important note : Users cannot be edited or removed once added to your Multi user PDF.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.