• Shopping Cart
    There are no items in your cart

ASTM F 3337 : 2019

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

Available format(s)

Hardcopy , PDF

Superseded date

11-12-2023

Superseded by

ASTM F 3337 : 2023

Language(s)

English

Published date

21-03-2019

€59.22
Excluding VAT

This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil.

Committee
F 20
DocumentType
Guide
Pages
4
ProductNote
THIS STANDARD ALSO REFERS TO- ASTM D5002 - 18
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

1.1This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.

1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.

1.3The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.

1.4The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.

1.5The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F 3634 : 2023 Standard Guide for Preparing Weathered Samples of Oil Using a Rotary Evaporator

ASTM F 3045 : 2020 Standard Test Method for Evaluation of the Type and Viscoelastic Stability of Water-in-oil Mixtures Formed from Crude Oil and Petroleum Products Mixed with Water
ASTM D 4377 : 2000 : EDT 1 Standard Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration
ASTM D 6450 : 2012 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 6450 : 2016 : REV A Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM F 3045 : 2015 : EDT 1 Standard Test Method for Evaluation of the Type and Viscoelastic Stability of Water-in-oil Mixtures Formed from Crude Oil and Petroleum Products Mixed with Water
ASTM D 5949 : 1996 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 7042 : 2019 : EDT 1 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 1824 : 1995 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
ASTM D 7042 : 2012 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4294 : 2010 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM F 2059 : 2006 : R2012 : EDT 1 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using The Swirling Flask
ASTM D 5002 : 2016 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 5853 : 2006 Standard Test Method for Pour Point of Crude Oils
ASTM F 2059 : 2000 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using The Swirling Flask
ASTM D 6352 : 1998 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700&#176C by Gas Chromatography
ASTM D 4377 : 2000 Standard Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration
ASTM D 6450 : 2012 : EDT 1 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 7042 : 2016 : EDT 2 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM F 2059 : 2017 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Swirling Flask
ASTM D 5853 : 2017 : REV A Standard Test Method for Pour Point of Crude Oils
ASTM D 5002 : 2015 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 1824 : 2016 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
ASTM D 7094 : 2017 : REV A Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 7042 : 2010 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 5949 : 2008 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 7094 : 2016 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM F 3045 : 2015 Standard Test Method for Evaluation of the Type and Viscoelastic Stability of Water-in-oil Mixtures Formed from Crude Oil and Petroleum Products Mixed with Water
ASTM D 6352 : 2014 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 7042 : 2016 : EDT 1 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 93 : 2019 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 4377 : 2000 : R2006 Standard Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration
ASTM D 1310 : 2014 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 7169 : 2020 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 5853 : 2016 Standard Test Method for Pour Point of Crude Oils
ASTM D 5002 : 2018 : EDT 1 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 5002 : 1999 : R2010 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 1310 : 1986 : R1997 : EDT 1 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 5853 : 2011 Standard Test Method for Pour Point of Crude Oils
ASTM D 7042 : 2020 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 5002 : 2013 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 93 : 1990 : EDT 1 Standard Test Methods for Flash Point by Pensky-Martens Closed Tester
ASTM D 6450 : 1999 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 5949 : 2001 : EDT 1 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 1310 : 2001 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 6352 : 2003 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700°C by Gas Chromatography
ASTM D 6352 : 2019 : EDT 1 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 4294 : 2008 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 7042 : 2011 : REV A Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 5002 : 2019 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 6352 : 2004 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700°C by Gas Chromatography
ASTM D 7042 : 2021 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 7169 : 2016 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 4294 : 2008 : REV A Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5949 : 2016 : R2022 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 6352 : 2004 : EDT 1 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700°C by Gas Chromatography
ASTM D 7094 : 2012 : EDT 1 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 4294 : 2002 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 7042 : 2004 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 1824 : 1966 : R1972 Standard Method Of Test For Apparent Viscosity Of Plastisols And Organosols At Low Shear Rates By Brookfield Viscometer
ASTM D 5949 : 2016 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 5853 : 2017 Standard Test Method for Pour Point of Crude Oils
ASTM D 7094 : 2012 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 7169 : 2018 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 97 : 2017 : REV B Standard Test Method for Pour Point of Petroleum Products
ASTM D 1824 : 1995 : R2010 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
ASTM D 7042 : 2019 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6560 : 2000 : R2005 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products
ASTM F 2059 : 2006 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using The Swirling Flask
ASTM D 4294 : 2016 : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 5949 : 2010 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 6450 : 2005 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 1310 : 2001 : R2007 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 7042 : 2012 : REV A Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4294 : 2008 : REV A : EDT 1 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM F 3251 : 2021 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Baffled Flask
ASTM D 7169 : 2011 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 6450 : 2016 : REV A : R2021 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 4294 : 1998 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 6352 : 2019 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 6450 : 2005 : R2010 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
ASTM D 7169 : 2019 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 5949 : 2014 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 1310 : 2014 : R2021 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
ASTM D 7042 : 2016 : EDT 3 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 4294 : 2021 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 93 : 2000 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 6352 : 2004 : R2009 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700°C by Gas Chromatography
ASTM D 7169 : 2020 : EDT 1 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 97 : 2017 : REV B : R2022 Standard Test Method for Pour Point of Petroleum Products
ASTM D 5949 : 2001 Standard Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)
ASTM D 93 : 1985 Standard Test Method for Flash Point by Pensky-Martens Closed Tester
ASTM D 5853 : 1995 Standard Test Method for Pour Point of Crude Oils
ASTM F 3251 : 2017 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Baffled Flask
ASTM F 2059 : 2021 Standard Test Method for Laboratory Oil Spill Dispersant Effectiveness Using the Swirling Flask
ASTM D 6560 : 2012 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products
ASTM D 5002 : 1999 : R2005 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 7042 : 2012 : EDT 1 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM F 3045 : 2021 Standard Test Method for Evaluation of the Type and Viscoelastic Stability of Water-in-oil Mixtures Formed from Crude Oil and Petroleum Products Mixed with Water
ASTM D 6560 : 2000 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products
ASTM D 6352 : 2002 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700&#176C by Gas Chromatography
ASTM D 5002 : 2018 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 4294 : 2003 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry
ASTM D 7042 : 2021 : REV A Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 7169 : 2005 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 7094 : 2004 : R2009 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 4294 : 2016 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence Spectrometry
ASTM D 7042 : 2016 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6560 : 2017 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products
ASTM D 1824 : 1995 : R2002 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
ASTM D 5002 : 2022 Standard Test Method for Density, Relative Density, and API Gravity of Crude Oils by Digital Density Analyzer
ASTM D 93 : 1997 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
ASTM D 7094 : 2004 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 7169 : 2023 Standard Test Method for Boiling Point Distribution of Samples with Residues Such as Crude Oils and Atmospheric and Vacuum Residues by High Temperature Gas Chromatography
ASTM D 4377 : 2000 : R2011 Standard Test Method for Water in Crude Oils by Potentiometric Karl Fischer Titration (Withdrawn 2020)
ASTM D 5853 : 2009 Standard Test Method for Pour Point of Crude Oils
ASTM D 6560 : 2022 Standard Test Method for Determination of Asphaltenes (Heptane Insolubles) in Crude Petroleum and Petroleum Products
ASTM D 4294 : 1990 : R1998 : EDT 1 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
ASTM D 7042 : 2014 Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
ASTM D 6352 : 2015 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
ASTM D 93 : 2018 Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
ASTM D 7094 : 2017 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester
ASTM D 5002 : 1999 Standard Test Method for Density and Relative Density of Crude Oils by Digital Density Analyzer
ASTM D 6352 : 2012 Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 to 700°C by Gas Chromatography
ASTM D 6450 : 2016 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.