ASTM F 755 : 1999 : R2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
Hardcopy , PDF
19-08-2020
English
01-12-2011
CONTAINED IN VOL. 13.01, 2015 Defines the properties and test methods for porous high density and ultra high molecular weight polyethylenes intended for use in surgical implants.
Committee |
F 04
|
DocumentType |
Standard
|
Pages |
3
|
ProductNote |
Reconfirmed 2011
|
PublisherName |
American Society for Testing and Materials
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 This specification covers the properties and test methods for porous high density and ultra high molecular weight polyethylenes intended for use in surgical implants. The porous polyethylene may be used as a free standing product or as a coating on a substrate in nonloaded applications.
1.2 Evaluation of tissue response to a porous polyethylene must be completed. Guidance in establishing biocompatibility may be found in the list of references.
1.3 Clinical experience and animal studies have shown that tissue will grow into the open pores of porous polyethylene. The tissue ingrowth into the pores may allow for the establishment of implant fixation.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This section does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D 1238 : 2000 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1238 : 2004 : REV C | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 732 : 2017 : REDLINE | Standard Test Method for Shear Strength of Plastics by Punch Tool |
ASTM D 1238 : 2013 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1621 : 2010 | Standard Test Method for Compressive Properties Of Rigid Cellular Plastics |
ASTM D 1238 : 2010 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
CFR 21(PTS170-199) : 0 | FOOD AND DRUGS - FOOD AND DRUG ADMINISTRATION, CHAPTER 1 DEPARTMENT OF HEALTH AND HUMAN SERVICES - PARTS 170-199 |
ASTM E 562 : 2011 : REDLINE | Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count |
ASTM D 2238 : 1992 : R2004 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm |
ASTM D 1623 : 2017 : REDLINE | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1505 : 2003 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1621 : 2016 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM D 1621 : 2004 | Standard Test Method for Compressive Properties Of Rigid Cellular Plastics |
ASTM D 1623 : 2003 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1621 : 2004 : REV A | Standard Test Method for Compressive Properties Of Rigid Cellular Plastics |
ASTM D 1898 : 1968 : R1989 | Standard Practice for Sampling of Plastics (Withdrawn 1998) |
ASTM D 2238 : 1992 : R2012 : EDT 1 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm<sup>−1</sup> (Withdrawn 2021) |
ASTM D 2873 : 1994 : R1999 : EDT 1 | Standard Test Method for Interior Porosity of Poly(Vinyl Chloride) (PVC) Resins by Mercury Intrusion Porosimetry (Withdrawn 2003) |
ASTM D 1623 : 2009 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1238 : 2004 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1505 : 1968 : R1979 | Standard Test Method for Density Of Plastics By The Density-Gradient Technique |
ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
ASTM D 1623 : 1978 : R1995 | Standard Test Method for Tensile And Tensile Adhesion Properties Of Rigid Cellular Plastics |
ASTM D 1621 : 2000 | Standard Test Method for Compressive Properties Of Rigid Cellular Plastics |
ASTM D 1621 : 1994 | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM F 748 : 2016 : REDLINE | Standard Practice for Selecting Generic Biological Test Methods for Materials and Devices |
ASTM D 1505 : 2010 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 2238 : 1992 : R1999 | Standard Test Methods for Absorbance of Polyethylene Due to Methyl Groups at 1378 cm |
ASTM D 1505 : 2018 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1505 : 1998 : EDT 1 | Standard Test Method for Density of Plastics by the Density-Gradient Technique |
ASTM D 1623 : 2017 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics |
ASTM D 1238 : 2001 : EDT 1 | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 1621 : 2016 : REDLINE | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM D 1238 : 2004 : REV A | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 1238 : 1985 | Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM F 648 : 2014 : REDLINE | Standard Specification for Ultra-High-Molecular-Weight Polyethylene Powder and Fabricated Form for Surgical Implants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.