BS 4364:1993
Current
The latest, up-to-date edition.
Specification for industrial oxygen
Hardcopy , PDF
English
15-02-1993
Committees responsible
Foreword
Specification
1. Scope
2. References
3. Description
4. Sampling
5. Oxygen content
6. Carbon monoxide and carbon dioxide content
7. Total hydrocarbons content
8. Water content
9. Containers
10. Labelling
Annexes
A. (informative) Safety considerations for the handling
of oxygen
B. (normative) Method for the determination of oxygen
content
C. (normative) Method for the determination of carbon
monoxide and carbon dioxide content
D. (normative) Method for the determination of total
hydrocarbons content
E. (normative) Method for the determination of water
content
Figures
B.1 Dumb-bell system: forces within the cell
B.2 Measuring cell configuration
B.3 Typical analyser configuration (electronic)
D.1 Flame ionization detector (schematic)
List of references
Not applicable to oxygen for medical, breathing or electronics applications.
Committee |
CII/26
|
DevelopmentNote |
Supersedes 92/51608 DC and BS 4364(1968). (08/2005) Reviewed and confirmed by BSI, December 2011. (11/2011)
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
This British Standard specifies requirements for oxygen that is to be used in industrial applications. It also describes the analytical principles and methods to be used to demonstrate compliance with the specification. Requirements for containers and their labelling are also specified.
This standard does not apply to oxygen for medical, breathing, electronics, or other applications where more demanding impurity limits may apply.
NOTE The oxygen is referred to hereafter as “the product??.
BS 4559-5.3:1987 | Methods for preparation of calibration gas mixtures. Dynamic volumetric methods Periodic injections into a flowing gas stream |
BS 4559-9.2:1988 | Methods for preparation of calibration gas mixtures. Comparison methods and methods for establishing traceability Checking by a comparison method |
BS 349:1973 | Specification for identification of the contents of industrial gas containers |
BS 4559-9.1:1988 | Methods for preparation of calibration gas mixtures. Comparison methods and methods for establishing traceability Determination of composition by comparison methods |
BS 5309-2:1976 | Methods for sampling chemical products Sampling of gases |
BS 4366:1993 | Specification for industrial nitrogen |
BS 4559-5.4:1987 | Methods for preparation of calibration gas mixtures. Dynamic volumetric methods Continuous injection method |
BS 4559-5.1:1987 | Methods for preparation of calibration gas mixtures. Dynamic volumetric methods Review of methods of calibration |
BS 4314-1:1968 | Specification for apparatus for physical methods of gas analysis Infra-red gas analysers for industrial use |
BS 4559-3:1983 | Methods for preparation of calibration gas mixtures Static volumetric methods |
BS 4559-6:1981 | Methods for preparation of calibration gas mixtures Saturation method |
BS 4559-7:1981 | Methods for preparation of calibration gas mixtures Permeation method |
BS 4559-5.6:1987 | Methods for preparation of calibration gas mixtures. Dynamic volumetric methods Sonic orifices |
BS 4559-1.1:1983 | Methods for preparation of calibration gas mixtures. Weighing methods Mixtures containing components fully vaporizable under ambient conditions |
BS 5443:1977 | Recommendations for a standard layout for methods of chemical analysis by gas chromatography |
BS 4559-8:1985 | Methods for preparation of calibration gas mixtures Mass dynamic method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.