BS 6374-1:1985
Current
The latest, up-to-date edition.
Lining of equipment with polymeric materials for the process idustries. Specification for lining with sheet thermoplastics
Hardcopy , PDF
English
28-02-1985
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Committees responsible
Specification
Section one. General
1.1 Scope
1.2 Definitions
1.3 Exchange of information
1.4 Compliance
Section two. Design, fabrication and surface finish
of equipment to be lined
2.1 General
2.2 Design of metal equipment to be lined
2.3 Fabrication of metal equipment to be lined
2.4 Design of concrete equipment to be lined
2.5 Construction of concrete equipment to be lined
Section three. Selection and quality of linings
3.1 Selection of lining
3.2 Quality of lining
3.3 Continuity of finished linings
Section four. Method of lining
4.1 Surface preparation
4.2 Lining process
Section five. Inspection and testing
5.1 Responsibility for inspection and testing
5.2 Inspection
Section six. Methods of test
6.1 Continuity testing
Section seven. Rectification of faults
7.1 General
Section eight. Storage, handling, transportation and
installation
8.1 General
Appendices
A Characteristics of thermoplastics used as sheet
linings specified in 3.1
B Continuity testing
C Effect of materials on water quality
Figures
1 Pipework details
2 Weld profile details: butt welds
3 Weld profile details: external corners and edges
4 Weld profile details: internal corners and edges
5 Weld profile details: concave heads
6 Weld profile details: flanges
Specifies requirements for the design and fabrication of equipment to be lined and the application and inspection of the lining along with provisions for any repairs. It applies to sheet thermoplastics for lining steel and concrete equipment. Guidance is given on the properties of typical linings of this category.
| Committee |
PVE/1
|
| DevelopmentNote |
Supersedes BS CP3003-1(1967), BS CP3003-3(1965) and BS CP3003-5(1966) (07/2004) Supersedes 81/78482 DC (09/2005) Reviewed and confirmed by BSI, October 2012. (09/2012)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This Part of BS 6374 specifies requirements for the lining of equipment for the process industries using sheet thermoplastics.
It includes requirements for the choice of lining and its application and also requirements for inspection of the lining and the rectification of faults. It applies to equipment fabricated in metal or concrete and to both bonded and loose linings.
NOTE 1. The linings may be applied at the applicator’s works or on site.
Requirements for design and fabrication of the equipment and the state of preparation necessary for the surfaces to be lined are specified in section two.
Requirements for storage, handling, transportation and installation of the lined equipment are specified in section eight.
NOTE 2. The titles of the publications referred to in this standard are listed on the inside back cover.
| BS 5493:1977 | Code of practice for protective coating of iron and steel structures against corrosion |
| BS 2782-3:Methods 320A to 320F:1976 | Methods of testing plastics. Mechanical properties Tensile strength, elongation and elastic modulus |
| BS CP110(1972) : LATEST | |
| BS 358:1960 | Method for the measurement of voltage with sphere-gaps (one sphere earthed) |
| BS 5337:1976 | Code of practice for the structural use of concrete for retaining aqueous liquids |
| BS 1755-1:1982 | Glossary of terms used in the plastics industry Polymer and plastics technology |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.