BS EN 12864 : 2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
Hardcopy , PDF
31-08-2013
English
01-01-2001
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1 Scope
2 Normative references
3 Terms and definitions
4 Terminology
5 Structural characteristics
6 Performance characteristics
7 Test methods
8 Marking - Packaging - Instructions
Annex A (normative) - Special requirements for
regulators fitted with pressure or rate
operated safety devices
Annex B (normative) - Special requirements for
regulators fitted with a temperature
operated safety device
Annex C (normative) - Special requirements for
low pressure regulators under extreme
temperature conditions
Annex D (normative) - Multimode connection regulator
for LPG cylinders to supply appliances installed
in caravans and motor caravans or freshwater boats
Annex E (normative) - Complementary test requirements for
non metallic thermoplastic or thermosetting materials
used in the construction of regulators
Annex F (normative) - Supplementary requirements for
reinforced diaphragms and elastomeric seals used in
LPG appliances and their associated equipment
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (normative) - Special requirements for low pressure
non adjustable regulators fitted with two or three
outlets for outdoor use
Annex J (normative) - Method for measuring leaks at test
pressures less than or equal to 20 bar
Annex K (normative) - Special requirements for regulators
fitted with an inlet valve
Annex L (informative) - Alternative test method for
resistance to corrosion
Annex M (normative) - Regulator for LPG cylinders to supply
appliances installed in seawater boats
Annex ZA (informative) - Clauses of this European Standard
addressing essential requirements or other provisions
of EU directives
Specifies the structural and operational characteristics, the safety requirements and test methods, the marking, of low-pressure, non adjustable regulators for butane, propane or their mixtures, referred to in the body of the text as 'regulators'.
| Committee |
GSE/24
|
| DevelopmentNote |
Supersedes 97/708497 DC (01/2004) Together with BS EN 13785 and BS EN 13786 supersedes BS 3016(1989). (08/2005) Supersedes 05/30132397 DC. (03/2006) 2001 Edition Re-Issued in March 2010 & incorporates AMD 3 2009. Supersedes 09/30189572 DC. (03/2010)
|
| DocumentType |
Standard
|
| Pages |
124
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 12864 : 2010 | Identical |
| NS EN 12864 : 2001 AMD 3 2009 | Identical |
| UNE-EN 12864:2002 | Identical |
| NF EN 12864 : 2002 AMD 3 2009 | Identical |
| I.S. EN 12864:2001 | Identical |
| NBN EN 12864 : 2002 AMD 3 2009 | Identical |
| NEN EN 12864 : 2002 AMD 3 2009 | Identical |
| DIN EN 12864:2006-03 | Identical |
| SN EN 12864 : 2001 AMD 3 2010 | Identical |
| DIN EN 12864 E : 2006 AMD 3 2010 | Identical |
| 13/30199128 DC : 0 | BS 6891 - SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) IN PREMISES |
| 12/30258581 DC : 0 | BS 5908-2 - FIRE AND EXPLOSION PRECAUTIONS AT PREMISES HANDLING FLAMMABLE GASES, LIQUIDS AND DUSTS - PART 2: GUIDE TO APPLICABLE STANDARDS AND REGULATIONS |
| PD 5482-3:2005 | Code of practice for domestic butane and propane gas-burning installations Installations in boats, yachts and other vessels |
| BS 5482-1:2005 | Code of practice for domestic butane- and propane-gas-burning installations Installations at permanent dwellings, residential park homes and commercial premises, with installation pipework sizes not exceeding DN 25 for steel and DN 28 for corrugated stainless steel or copper |
| BS 6891:2015 | Specification for the installation and maintenance of low pressure gas installation pipework of up to 35 mm (R1¼) on premises |
| PD 54823:2016 | Guidance for the design, commissioning and maintenance of LPG systems in small craft |
| BS 5908-2:2012 | Fire and explosion precautions at premises handling flammable gases, liquids and dusts Guide to applicable standards and regulations |
| 15/30281782 DC : 0 | PD 5482-3 - GUIDANCE FOR THE DESIGN, COMMISSIONING AND MAINTENANCE OF LPG SYSTEMS IN SMALL CRAFT |
| ISO 426-1:1983 | Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 1: Non-leaded and special copper-zinc alloys |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 75:1987 | Plastics and ebonite Determination of temperature of deflection under load |
| ISO 426-2:1983 | Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 2: Leaded copper-zinc alloys |
| ISO 565:1990 | Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings |
| EN 561:2002 | Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes |
| EN ISO 7253 : 2001 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 7253:1996 | Paints and varnishes — Determination of resistance to neutral salt spray (fog) |
| EN ISO 4628-3:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| 1990/396/EEC : 1990 | COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.