Skip to content
Please enter a keyword to search

  • BS EN 15015:2007

    Withdrawn A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

    Plastics piping systems. Systems for hot and cold water not intended for human consumption. Performance characteristics for pipes, fittings and their joints

    Available format(s):  Hardcopy, PDF

    Withdrawn date:  18-12-2020

    Language(s):  English

    Published date:  29-02-2008

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions and symbols
    4 Performance requirements
      4.1 Reaction to fire
      4.2 Internal pressure strength and resistance to high
          temperature
      4.3 Dimensional tolerances
      4.4 Tightness
      4.5 Durability
      4.6 Dangerous substances
    5 Test methods
      5.1 Reaction to fire
      5.2 Determination of the design pressure
      5.3 Dimensional tolerances
      5.4 Tightness and durability
    6 Evaluation of conformity
      6.1 General
      6.2 Initial type testing
      6.3 Factory production control
      6.4 One-off products and products produced in very low
          quantities
    Annex A (normative) Overall service (design) coefficients
          A.1 General
          A.2 Overall service (design) coefficients
    Annex B (normative) Product standards for hot and cold water
            installations inside buildings
    Annex C (normative) Standards for assessment of conformity
            for hot and cold water installations inside buildings
    Annex ZA (informative) Clauses of this European Standard
             addressing the provisions of the EU Construction
             Products Directive (CPD)
      ZA.1 Scope and relevant characteristics
      ZA.2 Procedure for attestation of conformity of plastics pipes
           and fittings
      ZA.3 CE marking and labelling
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes performance requirements for plastics pipes, fittings and their joints intended for hot and cold water installations for the conveyance of water and for heating systems with the exception of drinking water distribution for human consumption, and gives associated test methods for verification and evaluation of conformity with this European Standard.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/2
    Development Note Supersedes 04/30118854 DC. (03/2008)
    Document Type Standard
    Publisher British Standards Institution
    Status Withdrawn
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    93/68/EEC : 1993 AMD 2 1998 COUNCIL DIRECTIVE 93/68/EEC OF 22.7.93 AMENDING DIRECTIVES 87/404/EEC, 88/378/EEC, 89/106/EEC, 89/336/EEC, 89/392/EEC, 89/686/EEC, 90/384/EEC, 90/385/EEC, 90/396/EEC, 91/263/EEC, 92/42/EEC AND 73/23/EEC
    EN 15012:2007 Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints
    EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
    EN 12293:1999 Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling
    EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
    ISO 3213:2009 Polypropylene (PP) pipes Effect of time and temperature on the expected strength
    ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
    ISO 10146:1997 Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength
    89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
    EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
    EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
    ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
    ISO 17456:2006 Plastics piping systems Multilayer pipes Determination of long-term strength
    EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
    ISO 12230:2012 Polybutene-1 (PB-1) pipes — Effect of time and temperature on the expected strength
    EN ISO 9080:2012 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
    CEN/TR 15438:2007 Plastics piping systems - Guidance for coding of products and their intended uses
    ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
    EN ISO 13760:1998 Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998)
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 24033:2009 Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength
    ISO 10508:2006 Plastics piping systems for hot and cold water installations Guidance for classification and design
    ISO 9001:2015 Quality management systems — Requirements
    ISO 13760:1998 Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective