BS EN 303-5:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Heating boilers Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW. Terminology, requirements, testing and marking
Hardcopy , PDF
10-01-2022
English
31-08-2012
Committee |
RHE/24
|
DevelopmentNote |
Supersedes 95/712970 DC (08/2004) Supersedes 10/30228886 DC. (08/2012)
|
DocumentType |
Standard
|
Pages |
86
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
1.1 General This European Standard applies to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer. This European Standard deals with significant hazards, hazardous situations and events relevant to heating boilers used as intended and under the conditions foreseen by the manufacturer (see Clause 4). The boilers may operate under natural draught or forced draught. The stoking may work manually or automatically. NOTE This European Standard deals with boilers which are both within and outside of the scope of the Machinery Directive 2006/42/EC. This European Standard contains requirements and test methods for safety, combustion quality, operating characteristics, marking and maintenance of heating boilers. It also covers all external equipment that influences the safety systems (e.g. back burning safety device, integral fuel hopper). This European Standard covers only boilers that include burners as a unit. The standard applies to the combination of a boiler body with a solid fuel burner according to EN 15270 as a unit only when the whole unit is tested in accordance with this European Standard. Heating boilers in accordance with this European Standard are designed for central heating installations where the heat carrier is water and the maximum allowable temperature is 110 °C, and which can operate at a maximum allowable operating pressure of 6 bars. For heating boilers with a built-in or attached water heater (storage or continuous flow heater), this European Standard only applies to those parts of the water heater which are necessarily subject to the operating conditions of the heating boiler (heating part). This European Standard does not apply to: - heating boilers and other heating appliances which are also designed for the direct heating of the place of installation; - cooking appliances; - the design and construction of external fuel storage and transportation devices prior to the safety devices of the boiler; - room sealed applications; - condensing boilers. This European Standard specifies the necessary terminology for solid fuel heating boilers, the control and safety related requirements, the design requirements, the technical heating requirements (taking into account the environmental requirements) and testing, as well as the marking requirements. This European Standard is not applicable to heating boilers which are tested before the date of its publication as an EN (European Standard). (...)
Standards | Relationship |
UNI EN 303-5 : 2012 | Identical |
NF EN 303-5 : 2012 | Identical |
UNE-EN 303-5:2013 | Identical |
SN EN 303-5 : 2012 | Identical |
I.S. EN 303-5:2012 | Identical |
NBN EN 303-5 : 2012 | Identical |
NS EN 303-5 : 2012 | Identical |
DIN EN 303-5:2012-10 | Identical |
NEN EN 303-5 : 2012 | Identical |
EN 303-5:2012 | Identical |
ONORM EN 303-5 : 2012 | Identical |
EN 15270:2007 | Pellet burners for small heating boilers - Definitions, requirements, testing, marking |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
EN ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002) |
EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987) |
CEN/TS 15883:2009 | Residential solid fuel burning appliances - Emission test methods |
ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
EN 10027-2:2015 | DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM |
EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
ISO 13919-1:1996 | Welding Electron and laser-beam welded joints Guidance on quality levels for imperfections Part 1: Steel |
ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 11: Electron and laser beam welding |
EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
EN 14961-1:2010 | Solid biofuels - Fuel specifications and classes - Part 1: General requirements |
EN 304:2017 | Heating boilers - Test code for heating boilers for atomizing oil burners |
EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
EN 14597:2012 | Temperature control devices and temperature limiters for heat generating systems |
EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
EN 15456:2008 | Heating boilers - Electrical power consumption for heat generators - System boundaries - Measurements |
EN 303-1:2017 | Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking |
ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
EN 14778:2011 | Solid biofuels - Sampling |
EN 13501-2:2016 | Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services |
EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
EN 13526:2001 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon in flue gases from solvent using processes - Continuous flame ionisation detector method |
EN 14789:2017 | Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism |
EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
EN ISO 13919-1:1996 | Welding - Electrons and laser beam welded joints - Guidance on quality levels for imperfections - Part 1: Steel (ISO 13919-1:1996) |
IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
EN 13284-1:2017 | Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method |
EN 14961-2:2011 | Solid biofuels - Fuel specifications and classes - Part 2: Wood pellets for non-industrial use |
EN 13384-1:2015 | Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance |
EN 15058:2017 | Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry |
EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
EN 14961-4:2011 | Solid biofuels - Fuel specifications and classes - Part 4: Wood chips for non-industrial use |
EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
EN 10204:2004 | Metallic products - Types of inspection documents |
EN 14961-3:2011 | Solid biofuels - Fuel specifications and classes - Part 3: Wood briquettes for non-industrial use |
EN 12828:2012+A1:2014 | Heating systems in buildings - Design for water-based heating systems |
IEC 60730-2-5:2013+AMD1:2017 CSV | Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems |
EN 1563:2011 | Founding - Spheroidal graphite cast irons |
EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
EN 60730-2-5:2015 | Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems |
EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
EN ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding (ISO 15609-4:2009) |
ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
EN 14961-5:2011 | Solid biofuels - Fuel specifications and classes - Part 5: Firewood for non-industrial use |
EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
EN 14792:2017 | Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence |
ISO 857-2:2005 | Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms |
ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
EN 15036-1:2006 | Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators |
ISO 13919-2:2001 | Welding Electron and laser beam welded joints Guidance on quality levels for imperfections Part 2: Aluminium and its weldable alloys |
EN 1561:2011 | Founding - Grey cast irons |
EN 14961-6:2012 | Solid biofuels - Fuel specifications and classes - Part 6: Non-woody pellets for non-industrial use |
EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.