I.S. EN 303-5:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HEATING BOILERS - PART 5: HEATING BOILERS FOR SOLID FUELS, MANUALLY AND AUTOMATICALLY STOKED, NOMINAL HEAT OUTPUT OF UP TO 500 KW - TERMINOLOGY, REQUIREMENTS, TESTING AND MARKING
Hardcopy , PDF
08-05-2021
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test
6 Test report and other documents
7 Marking
8 Technical documentation, supplied with boiler
Annex A (informative) - Manual measurement of particles
in the gas flow, gravimetric determination of particle
load with filter systems
Annex B (normative) - Design criteria for solutions to prevent
back burning
Annex C (informative) - A-deviations
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
2006/42/EC Machinery Directive
Bibliography
Applicable to heating boilers including safety devices up to a nominal heat output of 500 kW which are designed for the burning of solid fuels only and are operated according to the instructions of the boiler manufacturer.
DocumentType |
Standard
|
Pages |
84
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNI EN 303-5 : 2012 | Identical |
NF EN 303-5 : 2012 | Identical |
UNE-EN 303-5:2013 | Identical |
SN EN 303-5 : 2012 | Identical |
NBN EN 303-5 : 2012 | Identical |
NS EN 303-5 : 2012 | Identical |
DIN EN 303-5:2012-10 | Identical |
NEN EN 303-5 : 2012 | Identical |
BS EN 303-5:2012 | Identical |
EN 303-5:2012 | Identical |
ONORM EN 303-5 : 2012 | Identical |
EN 15270:2007 | Pellet burners for small heating boilers - Definitions, requirements, testing, marking |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
EN ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002) |
EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987) |
CEN/TS 15883:2009 | Residential solid fuel burning appliances - Emission test methods |
ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
EN 10027-2:2015 | DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM |
EN 61000-6-3:2007/A1:2011/AC:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-3: GENERIC STANDARDS - EMISSION STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS (IEC 61000-6-3:2006/A1:2010) |
ISO 13919-1:1996 | Welding Electron and laser-beam welded joints Guidance on quality levels for imperfections Part 1: Steel |
ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 11: Electron and laser beam welding |
EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
EN 14961-1:2010 | Solid biofuels - Fuel specifications and classes - Part 1: General requirements |
EN 304:2017 | Heating boilers - Test code for heating boilers for atomizing oil burners |
EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
EN 14597:2012 | Temperature control devices and temperature limiters for heat generating systems |
EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
EN 15456:2008 | Heating boilers - Electrical power consumption for heat generators - System boundaries - Measurements |
EN 303-1:2017 | Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking |
ISO 7-2:2000 | Pipe threads where pressure-tight joints are made on the threads Part 2: Verification by means of limit gauges |
EN 14778:2011 | Solid biofuels - Sampling |
EN 13501-2:2016 | Fire classification of construction products and building elements - Part 2: Classification using data from fire resistance tests, excluding ventilation services |
EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
EN 13526:2001 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon in flue gases from solvent using processes - Continuous flame ionisation detector method |
EN 14789:2017 | Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism |
EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
EN ISO 13919-1:1996 | Welding - Electrons and laser beam welded joints - Guidance on quality levels for imperfections - Part 1: Steel (ISO 13919-1:1996) |
IEC 61000-6-3:2006+AMD1:2010 CSV | Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments |
EN 13284-1:2017 | Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method |
EN 14961-2:2011 | Solid biofuels - Fuel specifications and classes - Part 2: Wood pellets for non-industrial use |
EN 13384-1:2015 | Chimneys - Thermal and fluid dynamic calculation methods - Part 1: Chimneys serving one heating appliance |
EN 15058:2017 | Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry |
EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
EN 14961-4:2011 | Solid biofuels - Fuel specifications and classes - Part 4: Wood chips for non-industrial use |
EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
EN 10204:2004 | Metallic products - Types of inspection documents |
EN 14961-3:2011 | Solid biofuels - Fuel specifications and classes - Part 3: Wood briquettes for non-industrial use |
EN 12828:2012+A1:2014 | Heating systems in buildings - Design for water-based heating systems |
IEC 60730-2-5:2013+AMD1:2017 CSV | Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems |
EN 1563:2011 | Founding - Spheroidal graphite cast irons |
EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
EN 60730-2-5:2015 | Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner control systems |
EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
EN ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding (ISO 15609-4:2009) |
ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
EN 14961-5:2011 | Solid biofuels - Fuel specifications and classes - Part 5: Firewood for non-industrial use |
EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
EN 14792:2017 | Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence |
ISO 857-2:2005 | Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms |
ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
EN 15036-1:2006 | Heating boilers - Test regulations for airborne noise emissions from heat generators - Part 1: Airborne noise emissions from heat generators |
ISO 13919-2:2001 | Welding Electron and laser beam welded joints Guidance on quality levels for imperfections Part 2: Aluminium and its weldable alloys |
EN 1561:2011 | Founding - Grey cast irons |
EN 14961-6:2012 | Solid biofuels - Fuel specifications and classes - Part 6: Non-woody pellets for non-industrial use |
EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.