BS EN 60455-3-8:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Resin based reactive compounds used for electrical insulation Specifications for individual materials. Sheet 8: Resins for cable accessories
Hardcopy , PDF
09-10-2021
English
31-07-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Type testing
6 Test methods
7 Information on supply, packaging, marking and
labelling
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Provides the requirements for resins for power cable accessories which conform to this specification and meet established levels of performance.
| Committee |
GEL/15
|
| DocumentType |
Standard
|
| Pages |
18
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
This sheet 8 of IEC 60455-3 gives the requirements for resins for power cable accessories which conform to this specification and meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not on this specification alone.
| Standards | Relationship |
| EN 60455-3-8:2013 | Identical |
| IEC 60455-3-8:2013 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| HD 629.2 S2:2006/A1:2008 | TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 2: CABLES WITH IMPREGNATED PAPER INSULATION |
| ISO 7056:1981 | Plastics laboratory ware — Beakers |
| ISO 3521:1997 | Plastics — Unsaturated polyester and epoxy resins — Determination of overall volume shrinkage |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| IEC 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| IEC 60455-1:1998 | Resin based reactive compounds used for electrical insulation - Part 1: Definitions and general requirements |
| ISO 4895:2014 | Plastics — Liquid epoxy resins — Determination of tendency to crystallize |
| EN ISO 4895:2014 | Plastics - Liquid epoxy resins - Determination of tendency to crystallize (ISO 4895:2014) |
| HD 429 : 200S1 | METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
| ISO 2555:1989 | Plastics Resins in the liquid state or as emulsions or dispersions Determination of apparent viscosity by the Brookfield Test method |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 61234-2:1997 | Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| EN 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN 60212:2011 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| EN 50393:2015 | Test methods and requirements for accessories for use on distribution cables of rated voltage 0,6/1,0 (1,2) kV |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| HD 629.1 S2:2006/A1:2008 | TEST REQUIREMENTS ON ACCESSORIES FOR USE ON POWER CABLES OF RATED VOLTAGE FROM 3,6/6(7,2) KV UP TO 20,8/36(42) KV - PART 1: CABLES WITH EXTRUDED INSULATION |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.