BS ISO 81400-4:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Wind turbines Design and specification of gearboxes
Hardcopy , PDF
English
30-05-2008
30-04-2013
Foreword
1 Scope
2 Normative references
3 Definitions and symbols
4 Design specification
5 Gearbox design and manufacturing requirements
6 Lubrication
7 Other important items
Bibliography
Annexes
A - Wind turbine architecture
B - Wind turbine load description
C - Quality assurance
D - Operation and maintenance
E - Minimum purchaser and gearbox manufacturer
ordering data
F - Lubrication selection and condition monitoring
G - General gear information
H - Determination of the application factor, K[A],
from a given load spectrum using the equivalent
torque, T[eq]
I - Bearing stress calculation
Describes to gearboxes for wind turbines with power capacities ranging from 40 kW to 2 MW.
| Committee |
MCE/5
|
| DevelopmentNote |
Supersedes 04/30126296 DC. (05/2008)
|
| DocumentType |
Standard
|
| Pages |
104
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 81400-4:2005/Cor 1:2005 | Identical |
| ISO 81400-4:2005 | Identical |
| ISO 1328-2:1997 | Cylindrical gears — ISO system of accuracy — Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information |
| ISO/TR 13593:1999 | Enclosed gear drives for industrial applications |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) |
| AGMA 6025 : D | SOUND FOR ENCLOSED HELICAL, HERRINGBONE AND SPIRAL BEVEL GEAR DRIVES |
| AGMA 2101 : D | FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION) |
| AGMA 1010 : E | APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE |
| ISO 14104:2017 | Gears — Surface temper etch inspection after grinding, chemical method |
| ISO 1328-1:2013 | Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth |
| SAE J1165_198603 | REPORTING CLEANLINESS LEVELS OF HYDRAULIC FLUIDS |
| ISO 8579-2:1993 | Acceptance code for gears — Part 2: Determination of mechanical vibrations of gear units during acceptance testing |
| ISO/TR 13989-1:2000 | Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears — Part 1: Flash temperature method |
| DIN 7190:2001-02 | INTERFERENCE FITS - CALCULATION AND DESIGN RULES |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength |
| AGMA 6000 : B | SPECIFICATION FOR MEASUREMENT OF LINEAR VIBRATION ON GEAR UNITS |
| SAE AMS2301K | Steel Cleanliness, Aircraft Quality Magnetic Particle Inspection Procedure |
| AGMA 6001 : D | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| ISO 281:2007 | Rolling bearings — Dynamic load ratings and rating life |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials |
| ISO/TR 10064-3:1996 | Code of inspection practice — Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes |
| ISO/TR 10064-2:1996 | Code of inspection practice — Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash |
| AGMA 913 : A | METHOD FOR SPECIFYING THE GEOMETRY OF SPUR AND HELICAL GEARS |
| AGMA 925 : A | EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS |
| ASTM D 341 : 2017 : REDLINE | Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products |
| ISO/R 773:1969 | Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres) |
| ISO/TR 14179-1:2001 | Gears — Thermal capacity — Part 1: Rating gear drives with thermal equilibrium at 95 °C sump temperature |
| AGMA 9005 : E | INDUSTRIAL GEAR LUBRICATION |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors |
| AGMA 901 : A | A RATIONAL PROCEDURE FOR THE PRELIMINARY DESIGN OF MINIMUM VOLUME GEARS |
| ISO 16889:2008 | Hydraulic fluid power — Filters — Multi-pass method for evaluating filtration performance of a filter element |
| ISO/TR 10064-4:1998 | Code of inspection practice — Part 4: Recommendations relative to surface texture and tooth contact pattern checking |
| ISO 8579-1:2002 | Acceptance code for gear units — Part 1: Test code for airborne sound |
| AGMA 2004 : C | GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL |
| IEC 61400-1:2005+AMD1:2010 CSV | Wind turbines - Part 1: Design requirements |
| ISO/TR 10064-1:2017 | Code of inspection practice — Part 1: Measurement of cylindrical gear tooth flanks |
| ISO 76:2006 | Rolling bearings — Static load ratings |
| AGMA 1012 : 2005 | GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS |
| ASTM D 1744 : 2013 | Standard Test Method for Determination of Water in Liquid Petroleum Products by Karl Fischer Reagent (Withdrawn 2016) |
| ASTM A 534 : 2017 : REDLINE | Standard Specification for Carburizing Steels for Anti-Friction Bearings |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.