• CEI EN 60034-18-41 : 2014

    Current The latest, up-to-date edition.

    ROTATING ELECTRICAL MACHINES - PART 18-41: PARTIAL DISCHARGE FREE ELECTRICAL INSULATION SYSTEMS (TYPE I) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS - QUALIFICATION AND QUALITY CONTROL TESTS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2014

    Publisher:  Comitato Elettrotecnico Italiano

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1. Scope
    2. Normative references
    3. Terms and definitions
    4. Machine terminal voltages arising
        from converter operation
    5. Electrical stresses in the insulation
        system of machine windings
    6. Types of machine insulation
    7. Stress categories for Type I insulation
        systems used in converter fed machines
    8. Design qualification and type tests for
        Type I insulation systems
    9. Test equipment
    10. Qualification of the design of Type I
        insulation systems
    11. Type test procedure for Type I insulation
        systems
    12. Routine tests
    13. Analysis, reporting and classification
    Annex A (informative) - Derivation of possible
                            terminal voltages in service
                            for a converter-fed machine
    Annex B (normative) - Derivation of test voltages
                          for Type I insulation systems
    Annex C (normative) - Derivation of allowable
                          voltages in service
    Bibliography
    Annex ZA (normative) - Normative references
                           to international publications
                           with their corresponding
                           European publications

    Abstract - (Show below) - (Hide below)

    Describes the criteria for assessing the insulation system of stator/rotor windings which are subjected to voltage-source pulse-width- modulation (PWM) drives.

    General Product Information - (Show below) - (Hide below)

    Committee CT 2
    Development Note Classificazione CEI 2-52. (09/2014) NEW CHILD AMD 1 2020 IS ADDED
    Document Type Standard
    Product Note NEW CHILD AMD 1 2020 IS ADDED
    Publisher Comitato Elettrotecnico Italiano
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 60034-18-1:2010 ROTATING ELECTRICAL MACHINES - PART 18-1: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - GENERAL GUIDELINES
    CLC/TS 60034-27 : 2011 Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
    EN 60034-18-21:2013 ROTATING ELECTRICAL MACHINES - PART 18-21: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR WIRE-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION (IEC 60034-18-21:2012)
    EN 60034-18-31 : 2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012)
    IEC TS 60034-27:2006 Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
    IEC TS 61934:2011 Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses
    IEC TS 60034-18-42:2008 Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
    IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
    IEC 60172:2015 Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires
    IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
    IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
    EN 60172:2015 TEST PROCEDURE FOR THE DETERMINATION OF THE TEMPERATURE INDEX OF ENAMELLED AND TAPE WRAPPED WINDING WIRES (IEC 60172:2015)
    EN 60664-1:2007 INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS
    IEC 60034-18-21:2012 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
    CLC/TS 60034-25:2008 ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
    CLC/TS 60034-18-42 : 2011 ROTATING ELECTRICAL MACHINES - PART 18-42: QUALIFICATION AND ACCEPTANCE TESTS FOR PARTIAL DISCHARGE RESISTANT ELECTRICAL INSULATION SYSTEMS (TYPE 2) USED IN ROTATING ELECTRICAL MACHINES FED FROM VOLTAGE CONVERTERS
    IEC 60034-18-31:2012 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
    IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective