CSA ISO/IEC 14165-115 : 2006
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFORMATION TECHNOLOGY - FIBRE CHANNEL - PART 115: PHYSICAL INTERFACES (FC-PI)
Available format(s)
Hardcopy , PDF
Superseded date
26-07-2021
Superseded by
Language(s)
English
Published date
01-01-2016
Publisher
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions and conventions
4 Structure and concepts
5 FC-PI functional characteristics
6 Optical interface specification
7 Optical interface receptacle specifications
8 Optical fibre cable plant specification
9 Electrical cable interface specification
10 Electrical cable plant and connector specifications
Annex A (informative) - Test methods
Annex B (informative) - SERDES electrical interface example
Annex C (normative) - Optical cable plant usage
Annex D (normative) - Tx-Off and Rx-Loss of Signal detection
Bibliography
Defines the physical interface portions of a high performance serial link that supports the higher Upper Level Protocols (ULPs) associated with HIPPI, IPI, SCSI, IP and others.
| DocumentType |
Standard
|
| Pages |
118
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO/IEC 14165-115:2006 | Identical |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| ISO/IEC 14165-116:2005 | Information technology Fibre Channel Part 116: 10 Gigabit (10GFC) |
| IEC 61754-18:2001 | Fibre optic connector interfaces - Part 18: Type MT-RJ connector family |
| IEC 60807-3:1990 | Rectangular connectors for frequencies below 3 MHz - Part 3: Detail specification for a range of connectors with trapezoidal shaped metal shells and round contacts - Removable crimp contact types with closed crimp barrels, rear insertion/rear extraction |
| IEC 61280-1-3:2010 | Fibre optic communication subsystem test procedures - Part 1-3: General communication subsystems - Central wavelength and spectral width measurement |
| ISO/IEC 14165-141:2001 | Information technology Fibre Channel Part 141: Fabric Generic Requirements (FC-FG) |
| IEC 60793-2-10:2017 | Optical fibres - Part 2-10: Product specifications - Sectional specification for category A1 multimode fibres |
| IEC 60793-1-41:2010 | Optical fibres - Part 1-41: Measurement methods and test procedures - Bandwidth |
| IEC 60793-1-43:2015 | Optical fibres - Part 1-43: Measurement methods and test procedures - Numerical aperture measurement |
| IEC 61300-2-25:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-25: Tests - Sealing endurance for closures |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| ISO/IEC 14165-133:2010 | Information technology Fibre Channel Part 133: Switch Fabric-3 (FC-SW-3) |
| IEC 61300-3-3:2009 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-3: Examinations and measurements - Active monitoring of changes in attenuation and return loss |
| ISO/IEC 14165-222:2005 | Information technology Fibre Channel Part 222: Single-byte command code 2 mapping protocol (FC-SB-2) |
| ISO/IEC 11801:2002 | Information technology Generic cabling for customer premises |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61300-2-17:2010 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-17: Tests - Cold |
| IEC 60793-1-42:2013 | Optical fibres - Part 1-42: Measurement methods and test procedures - Chromatic dispersion |
| IEC 61300-2-5:2009 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-5: Tests - Torsion |
| ISO/IEC 14165-241:2005 | Information technology Fibre Channel Part 241: Backbone 2 (FC-BB-2) |
| ISO/IEC 14165-122:2005 | Information technology Fibre Channel Part 122: Arbitrated Loop-2 (FC-AL-2) |
| ISO/IEC 14165-414:2007 | Information technology Fibre Channel Part 414: Generic Services 4 (FC-GS-4) |
| ISO/IEC 14165-321:2009 | Information technology Fibre Channel Part 321: Audio-Video (FC-AV) |
| IEC 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| ISO/IEC 14165-131:2000 | Information technology Fibre Channel Part 131: Switch Fabric Requirements (FC-SW) |
| IEC 60793-1-40:2001 | Optical fibres - Part 1-40: Measurement methods and test procedures - Attenuation |
| IEC 61280-4-1:2009 | Fibre-optic communication subsystem test procedures - Part 4-1: Installed cable plant - Multimode attenuation measurement |
| IEC 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| IEC 61300-3-6:2008 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-6: Examinations and measurements - Return loss |
| IEC 61280-2-2:2012 | Fibre optic communication subsystem test procedures - Part 2-2: Digital systems - Optical eye pattern, waveform and extinction ratio measurement |
| IEC 61300-3-4:2012 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurements - Attenuation |
| IEC 60169-8:1978 | Radio-frequency connectors. Part 8: R.F. coaxial connectors with inner diameter of outer conductor 6.5 mm (0.256 in) with bayonet lock - Characteristic impedance 50 ohms (Type BNC) |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 60793-1-20:2014 | Optical fibres - Part 1-20: Measurement methods and test procedures - Fibre geometry |
| IEC 61300-2-4:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention |
| ISO/IEC TR 14165-117:2007 | Information technology Fibre Channel Part 117: Methodologies for jitter and signal quality (MJSQ) |
| IEC 61754-6:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 6: Type MU connector family |
| IEC 61754-20:2012 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family |
| IEC 61280-2-1:2010 | Fibre optic communication subsystem test procedures - Part 2-1: Digital systems - Receiver sensitivity and overload measurement |
| IEC 61754-4:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family |
| IEC 61754-1:2013 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 1: General and guidance |
| IEC 61300-2-6:2010 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-6: Tests - Tensile strength of coupling mechanism |
| ISO/IEC 14165-331:2007 | Information technology Fibre Channel Part 331: Virtual Interface (FC-VI) |
| ISO/IEC 14165-114:2005 | Information technology Fibre Channel Part 114: 100 MB/s Balanced copper physical interface (FC-100-DF-EL-S) |
| ISO/IEC 14165-251:2008 | Information technology Fibre Channel Part 251: Framing and Signaling (FC-FS) |
| IEC 61754-19:2001 | Fibre optic connector interfaces - Part 19: Type SG connector family |
| IEC 61076-3-103:2003 | Connectors for electronic equipment - Part 3-103: Rectangular connectors - Detail specification for single row connectors with non-removable ribbon cable contacts on 1,25 mm pitch used for high speed serial data (HSSDC) |
| IEC 61300-3-11:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-11: Examinations and measurements - Engagement and separation forces |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.