CSA Z245.20-Z245.21 : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EXTERNAL FUSION BOND EPOXY COATING FOR STEEL PIPE/EXTERNAL POLYETHYLENE COATING FOR PIPE
Hardcopy , PDF
23-07-2013
English
01-01-2006
Technical Committee on Petroleum and Natural Gas Industry
Pipeline Systems and Materials
Subcommittee on Materials
Preface
Z245.20-06, External fusion bond epoxy coating for steel pipe
1 Scope
2 Reference publications
3 Definitions
4 General requirements
4.1 Product ordering requirements
4.2 Rounding procedure
4.3 Requirements for quality
4.4 Compliance
5 Materials
5.1 Pipe
5.2 Epoxy powders
6 Coating application
6.1 Coating qualification
6.2 Production application practices and equipment
7 Inspection and testing
7.1 Inspection notice
7.2 Plant access
7.3 Tests
8 Repair of coated pipe
8.1 General
8.2 Patching
8.3 Stripping and recoating
9 Markings
9.1 General
9.2 Required markings
10 Handling and storage
10.1 Handling
10.2 Storage
11 Test reports and certificates of compliance
12 Test procedures
12.1 Cure time of the epoxy powder
12.2 Gel time of the epoxy powder
12.3 Moisture content of the epoxy powder - Titration
12.4 Moisture content of the epoxy powder - Mass loss
12.5 Particle size of the epoxy powder
12.6 Density of the epoxy powder
12.7 Thermal characteristics of the epoxy powder and coating
12.8 Cathodic disbondment of the coating
12.9 Interface contamination of the coating
12.10 Porosity of the coating
12.11 Flexibility of the coating
12.12 Impact resistance of the coating
12.13 Cathodic disbondment of strained coating
12.14 Adhesion of the coating
12.15 Gouge resistance of coating
12.16 Surface roughness measurement
Tables
Figures
Z245.21-06, External polyethylene coating for pipe
1 Scope
2 Reference publications
3 Definitions
4 General requirements
4.1 Product ordering requirements
4.2 Rounding procedure
4.3 Requirements for quality
4.4 Compliance
5 Materials
5.1 Pipe
5.2 Manufacturer's documentation
5.3 Primer
5.4 Adhesive
5.5 Polyethylene
5.6 Packaging
6 Coating application
6.1 Coating qualification
6.2 Production application practices and equipment
7 Production, inspection, and testing
7.1 Inspection Notice
7.2 Plant access
7.3 Incoming raw materials testing
7.4 Production tests
8 Repair of coated pipe
8.1 General
8.2 Patching
8.3 Stripping and recoating
9 Markings
9.1 General
9.2 Required markings
10 Handling and storage
10.1 Handling
10.2 Storage
11 Test reports and certificates of compliance
12 Test procedures
12.1 Viscosity
12.2 Flow
12.3 Cathodic disbondment of the coating
12.4 Peel adhesion (constant rate of peel)
12.5 Peel adhesion (hanging mass)
12.6 Heat aging
12.7 Gouge resistance
Tables
Figures
Includes the qualification, application, inspection, testing, handling, and storage of materials required for plant-applied fusion bond epoxy (FBE) coating applied externally to bare steel pipe.
DocumentType |
Standard
|
Pages |
142
|
PublisherName |
Canadian Standards Association
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
CSA Z662.1 : 2013 | COMMENTARY ON CSA Z662-07, OIL AND GAS PIPELINE SYSTEMS |
NACE SP 01 69 : 2013 | CONTROL OF EXTERNAL CORROSION ON UNDERGROUND OR SUBMERGED METALLIC PIPING SYSTEMS |
NACE RP 01 05 : 2005 | LIQUID-EPOXY COATINGS FOR EXTERNAL REPAIR, REHABILITATION, AND WELD JOINTS ON BURIED STEEL PIPELINES |
NACE SP 01 85 : 2007 | EXTRUDED POLYOLEFIN RESIN COATING SYSTEMS WITH SOFT ADHESIVES FOR UNDERGROUND OR SUBMERGED PIPE |
NACE 30105 : 0 | ELECTRICAL ISOLATION/CONTINUITY AND COATING ISSUES FOR OFFSHORE PIPELINE CATHODIC PROTECTION SYSTEMS |
ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
ASTM D 1238 : 2013 : REDLINE | Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
ASTM D 3895 : 2014 | Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry |
ASTM D 1525 : 2017 | Standard Test Method for Vicat Softening Temperature of Plastics |
ASTM D 2083 : 1992 : R1998 | Standard Test Method for Calculation of Percent of Primary, Secondary, and Tertiary Amines in Fatty Amines (Withdrawn 2007) |
ISO 9001:2015 | Quality management systems — Requirements |
CSA ISO 9001 : 2016 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS |
ASTM D 4703 : 2016 : REDLINE | Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets |
ASTM D 1475 : 2013 : REDLINE | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM D 746 : 2014 : REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
ASTM D 1693 : 2015 : REDLINE | Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.