Skip to content
Please enter a keyword to search

  • DD CEN/TS 13244-7:2003

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    View superseded by

    Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-03-2014

    Language(s):  English

    Published date:  23-01-2004

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviations
      3.1 Terms and definitions
      3.2 Abbreviations
    4 Requirements
      4.1 General
      4.2 Testing and inspection
    Annex A (normative) Change of PE compound
    Annex B (normative) Change of design
    Bibliography

    Abstract - (Show below) - (Hide below)

    Provides guidance for the assessment of conformity to be included in the manufacturer's quality plan as part of his quality system.

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88
    Development Note Supersedes 98/122501 DC. (05/2005)
    Document Type Standard
    Publisher British Standards Institution
    Revision Of
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
    EN 13244-1:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General
    ISO/IEC Guide 62:1996 General requirements for bodies operating assessment and certification/registration of quality systems
    ISO 3951:1989 Sampling procedures and charts for inspection by variables for percent nonconforming
    EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
    EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
    EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
    EN 13244-4:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 4: Valves
    ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    EN 13244-3:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 3: Fittings
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 9001:2015 Quality management systems — Requirements
    ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
    ISO/IEC Guide 65:1996 General requirements for bodies operating product certification systems
    ISO 6259-3:2015 Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes
    EN 45012 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
    EN 13244-5:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system
    EN 13244-2:2002 Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes
    EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective