DIN EN 12159:2013-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Builders hoists for persons and materials with vertically guided cages
Hardcopy , PDF
01-11-2024
English, German
01-03-2013
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
6 Verification
7 User information
Annex A (normative) - European stormwind map
Annex B (normative) - Electric safety devices
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Specifies power operated temporarily installed builders hoists (referred to as 'hoists' in this standard) intended for use by persons who are permitted to enter sites of engineering and construction, serving landing levels, having a cage: - designed for the transportation of persons or of persons and materials; - guided; - travelling vertically or along a path within 15 degrees max. of the vertical; - supported or sustained by drum driven wire rope, rack and pinion, hydraulic jack (direct or indirect), or an expanding linkage mechanism; - where masts, when erected, may or may not require support from separate structures.
| DevelopmentNote |
The 2020 draft version has release for the standard DIN EN 12159
|
| DocumentType |
Standard
|
| Pages |
68
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 12159 : 2013 | Identical |
| UNE-EN 12159:2013 | Identical |
| NBN EN 12159 : 2013 | Identical |
| NEN EN 12159 : 2012 | Identical |
| NS EN 12159 : 2012 | Identical |
| I.S. EN 12159:2012 | Identical |
| SN EN 12159 : 2012 | Identical |
| UNI EN 12159 : 2013 | Identical |
| BS EN 12159:2012 | Identical |
| EN 12159:2012 | Identical |
| ONORM EN 12159 : 2013 | Identical |
| EN 81-43:2009 | Safety rules for the construction and installation of lifts - Special lifts for the transport of persons and goods - Part 43: Lifts for cranes |
| ISO 2408:2017 | Steel wire ropes — Requirements |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 4302:2016 | Cranes — Wind load assessment |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| ISO 6336-2:2006 | Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting) |
| DIN 3990-1:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS - INTRODUCTION AND GENERAL INFLUENCE FACTORS |
| DIN 4844-1:2012-06 | GRAPHICAL SYMBOLS - SAFETY COLOURS AND SAFETY SIGNS - PART 1: OBSERVATION DISTANCES AND COLORIMETRIC AND PHOTOMETRIC REQUIREMENTS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| DIN EN 12385-1:2009-01 | STEEL WIRE ROPES - SAFETY - PART 1: GENERAL REQUIREMENTS |
| ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength |
| EN 12158-1:2000+A1:2010 | Builders' hoists for goods - Part 1: Hoists with accessible platforms |
| EN 81-1:1998+A3:2009 | Safety rules for the construction and installation of lifts - Part 1: Electric lifts |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN 12158-2:2000+A1:2010 | Builders' hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 6336-5:2016 | Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
| EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 81-2 : 1998 + A3 2009 | SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - PART 2: HYDRAULIC LIFTS |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| DIN 3990-2:1987-12 | CALCULATION OF LOAD CAPACITY CYLINDRICAL GEARS; CALCULATION OF PITTING RESISTANCE |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| DIN 3990-3:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; CALCULATION OF TOOTH STRENGTH |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.