DIN EN 15655:2016-07 (Draft)
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
07-03-2021
German
01-01-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Bestellangaben
5 Technische Anforderungen
5.1 Vorbereitung der Oberfläche
5.2 Fertig gestellte Polyurethan-Auskleidung
5.3 Rohrenden
5.4 Ausbesserungen
5.5 Kennzeichnung
5.6 Porenfreiheit
5.7 Härte
5.8 Haftfestigkeit
6 Anforderungen an die Funktion
6.1 Chemische Beständigkeit
6.2 Indirekte Schlagbeständigkeit
6.3 Beständigkeit gegen Querschnittsverformung
6.4 Bruchdehnung
6.5 Spezifischer Auskleidungswiderstand
6.6 Abriebbeständigkeit (nur für Abwasseranwendungen)
6.7 Lichtalterung
6.8 Werkstoffe, die mit Wasser für den menschlichen
Gebrauch in Berührung kommen
7 Prüfverfahren
7.1 Laufende Überprüfungen
7.2 Funktionsprüfungen
Anhang A (normativ) Qualitätssicherung
A.1 Allgemeines
A.2 Funktionsprüfung; Einteilung nach DN-Gruppen
A.3 Qualitätsbewertungssystem
Anhang B (informativ) Auskleidungsprozess und Werkstoffe
B.1 Auskleidungsprozess
B.2 Werkstoffeigenschaften
B.3 Anwendungsbereich, Eigenschaften des
transportierten Wassers
Anhang C (informativ) Verpackung
Literaturhinweise
Describes the requirements and test methods applicable to factory applied internal polyurethane high duty corrosion protection of buried ductile iron pipes and fittings conforming to EN 545, EN 598 and EN 969 for use at permanent operating temperatures up to 45 Degrees C.
| DevelopmentNote |
DRAFT 2016 issued in July 2016 is superseded by DIN EN 15655-1:DRAFT 2018. (01/2018)
|
| DocumentType |
Draft
|
| Pages |
49
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| EN 15655:2009 | Identical |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 8504-1:2000 | Preparation of steel substrates before application of paints and related products Surface preparation methods Part 1: General principles |
| EN 598:2007+A1:2009 | Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 4624:2016 | Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016) |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.