DIN EN ISO 11403-3:2002-02
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)
Hardcopy , PDF
07-03-2021
English
01-01-2002
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation
5 Conditioning
6 Test requirements
7 Presentation of data
8 Precision
Annex A (informative) - Information relating to
certain test requirements
Annex B (normative) - Chemicals for chemical
resistance and environmental
stress cracking resistance tests
Bibliography
Defines test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: - prolonged exposure to heat; - liquid chemicals; - environmental stress cracking under a constant tensile stress; - artificial weathering.
| DevelopmentNote |
The 2020 draft version has released for the standard DIN EN ISO 11403-3
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ONORM EN ISO 11403-3 : 2015 | Identical |
| EN ISO 11403-3:2014 | Identical |
| I.S. EN ISO 11403-3:2014 | Identical |
| UNI EN ISO 11403-3 : 2014 | Identical |
| NF EN ISO 11403-3 : 2014 | Identical |
| NS EN ISO 11403-3 : 2014 | Identical |
| SN EN ISO 11403-3 : 2014 | Identical |
| BS EN ISO 11403-3:2014 | Identical |
| NBN EN ISO 11403-3 : 2014 | Identical |
| NEN EN ISO 11403-3 : 2014 | Identical |
| UNE-EN ISO 11403-3:2014 | Identical |
| ISO 11403-3:2014 | Identical |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| ISO 2578:1993 | Plastics Determination of time-temperature limits after prolonged exposure to heat |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| ISO 175:2010 | Plastics Methods of test for the determination of the effects of immersion in liquid chemicals |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| ISO 20753:2008 | Plastics Test specimens |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.