DIN VDE 0636-10 : 1992
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LOW-VOLTAGES FUSES; GENERAL REQUIREMENTS
01-11-1999
12-01-2013
Vorwort
1 Allgemeines
1.1 Anwendungsbereich
1.2 Zweck
2 Begriffe
2.1 Sicherungen und ihre Bauteile
2.2 Allgemeine Begriffe
2.3 Kenngrössen
3 Betriebsbedingungen
3.1 Umgebungstemperatur (Ta)
3.2 Höhe
3.3 Atmosphärische Bedingungen
3.4 Spannung
3.5 Strom
3.6 Frequenz, Leistungsfaktor und Zeitkonstante
3.7 Einbaubedingungen
3.8 Betriebsklasse
3.9 Selektivität von "gG"- und "gM"-Sicherungen
4 Klassifikation
5 Kenngrössen von Sicherungen
5.1 Aufzählungen der Kenngrössen
5.2 Bemessungsspannung
5.3 Bemessungsstrom
5.4 Bemessungsfrequenz
5.5 Bemessungsleistungsabgabe eines Sicherungseinsatzes
und Bemessungsleistungsaufnahme eines
Sicherungshalters
5.6 Grenzen der Zeit/Strom-Kennlinien
5.7 Ausschaltbereich und Ausschaltvermögen
5.8 Durchlassstrom- und I[2]t-Kennlinien
6 Aufschriften
6.1 Aufschriften auf Sicherungshaltern
6.2 Aufschriften auf Sicherungseinsätzen
6.3 Schaltzeichen
7 Anforderungen an den Aufbau
7.1 Mechanische Ausführung
7.2 Isolationseigenschaften
7.3 Erwärmung, Leistungsabgabe des Sicherungseinsatzes
und Leistungsaufnahme des Sicherungshalters
7.4 Funktion
7.5 Ausschaltvermögen
7.6 Durchlassstrom-Kennlinie
7.7 I[2]t-Kennlinien
7.8 Selektivität von "gG"- und "gM"-Sicherungseinsätzen
7.9 Berührungsschutz
7.10 Wärmebeständigkeit
7.11 Mechanische Festigkeit
7.12 Widerstandsfähigkeit gegen Korrosion
7.13 Widerstandsfähigkeit gegen übermässige Wärme und
gegen Feuer
8 Prüfungen
8.1 Allgemeines
8.2 Nachweis der Isolationseigenschaften
8.3 Prüfung der Erwärmung und der Leistungsabgabe
8.4 Prüfung der Funktionsfähigkeit
8.5 Prüfung des Ausschaltvermögens
8.6 Prüfung der Durchlassstrom-Kennlinie
8.7 Prüfung der I[2]t-Kennlinien und Selektivität
8.8 Prüfung der Schutzart der Umhüllungen
8.9 Prüfung der Wärmebeständigkeit
8.10 Alterungsbeständigkeit der Kontakte
8.11 Mechanische Prüfungen; andere Prüfungen
Bilder 1 bis 8
Anhang A (normativ) Messung des Leistungsfaktors bei
Kurzschluss
Anhang B (normativ) Ermittlung der Schmelz-I[2]t-Werte für
"gG"- und "gM"-Sicherungseinsätze
Anhang C (normativ) Ermittlung der
Durchlassstrom/Zeit-Kennlinie
Anhang D (normativ) Einfluss der Änderung von
Umgebungstemperatur und Einbaubedingungen auf die
Funktion von Sicherungseinsätzen
Anhang ZA (normativ) Andere in dieser Norm zitierte
internationale Publikationen
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60269-1:2007/A2:2014 | Identical |
| VDE 0636-10 : 2005 | Identical |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Corresponds |
| DIN EN 61642 : 1998 | INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS |
| VDE 0419-1 : 94 AMD 2 99 | TIME SWITCHES FOR TARIFF AND LOAD CONTROL |
| VDE 0418-20 : 1996 | ELECTRIC INTEGRATING METERS - ALTERNATING CURRENT STATIC VARHOUR METERS FOR REACTIVE ENERGY (CLASSES 2 AND 3) |
| VDE 0420-1 : 94 AMD 2 99 | ELECTRONIC RIPPLE CONTROL RECEIVERS FOR TARIFF AND LOAD CONTROL |
| VDE 0160 : 1998-04 | ELECTRONIC EQUIPMENT FOR USE IN POWER INSTALLATIONS |
| VDE 0636-2011 : 1999 | LOW-VOLTAGE FUSES - PART 2-1: SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY AUTHORIZED PERSONS (FUSES MAINLY FOR INDUSTRIAL APPLICATION); NATIONAL SUPPLEMENT 1: PROTECTION OF SPECIAL ELECTRICAL SYSTEMS |
| DIN EN 50091-1-1 : 1997 | |
| VDE 0636-3011 : 1999 | LOW-VOLTAGE FUSES - PART 3-1: SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY UNSKILLED PERSONS (FUSES MAINLY FOR HOUSEHOLD AND SIMILAR APPLICATIONS); NATIONAL SUPPLEMENT 1: U(INDEX)AC = 690 V AND U(INDEX)DC = 600 V |
| DIN VDE 0636-3011 : 1999 | LOW-VOLTAGE FUSES - PART 3-1: SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY UNSKILLED PERSONS (FUSES MAINLY FOR HOUSEHOLD AND SIMILAR APPLICATIONS); NATIONAL SUPPLEMENT 1: U(INDEX)AC = 690 V AND U(INDEX)DC = 600 V |
| DIN VDE 0636-2011 : 1999 | LOW-VOLTAGE FUSES - PART 2-1: SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY AUTHORIZED PERSONS (FUSES MAINLY FOR INDUSTRIAL APPLICATION); NATIONAL SUPPLEMENT 1: PROTECTION OF SPECIAL ELECTRICAL SYSTEMS |
| DIN EN 61268 : 1996 | ALTERNATING CURRENT STATIC VAR-HOUR METERS FOR REACTIVE ENERGY (CLASSES 2 AND 3) |
| DIN EN 61038 : 1994 AMD 2 1999 | TIME SWITCHES FOR TARIFF AND LOAD CONTROL |
| DIN EN 50017 : 2000 | ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - POWDER FILLING 'Q' |
| DIN EN 61037 : 1994 AMD 2 1999 | ELECTRONIC RIPPLE CONTROL RECEIVERS FOR TARIFF AND LOAD CONTROL |
| VDE 0560-430 : 1998 | INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS |
| IEC 60038:2009 | IEC standard voltages |
| DIN VDE 0820-1 : 1992 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINK |
| HD 119 : 200S1 | FUSE-HOLDERS FOR MINIATURE CARTRIDGE FUSE-LINKS |
| VDE 0820-1 : 2015 | Miniature fuses Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links (IEC 60127-1:2006 + A1:2011 + A2:2015); |
| DIN IEC 60038 : 2002 | IEC STANDARD VOLTAGES |
| IEC 60127:1974 | Cartridge fuse-links for miniature fuses |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| IEC 60364-5-523:1999 | Electrical installations of buildings - Part 5: Selection and erection of electrical equipment - Section 523: Current-carrying capacities in wiring systems |
| DIN 43655:1969-10 | FORMS OF DOUBLE LOGARITHMIC PAPER WITH SCALES IN THE RATIO 2:1 |
| DIN 40050:1980-07 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES; PROTECTION OF ELECTRICAL EQUIPMENT AGAINST CONTACT, FOREIGN BODIES AND WATER |
| VDE 0636-105 : DRAFT 83 | LOW-VOLTAGE FUSES - SUPPLEMENTARY REQUIREMENTS FOR FUSES FOR USE BY AUTHORIZED PERSONS |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 60269-2:2013+AMD1:2016 CSV | Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K |
| DIN 40200:1981-10 | NOMINAL VALUE, LIMITING VALUE, RATED VALUE, RATING - CONCEPTS |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| DIN VDE 0660-107 : 1992 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS |
| DIN 40100-1:1986-01 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT IN THE ELECTROTECHNICAL FIELD; GENERAL INFORMATION |
| ISO 478:1974 | Paper — Untrimmed stock sizes for the ISO-A Series — ISO primary range |
| HD 422 : 200S1 | LOW VOLTAGE AIRBREAK SWITCHES, AIRBREAK DISCONNECTORS, AIRBREAK SWITCH DISCONNECTORS AND FUSE COMBINATION UNITS |
| IEC 60291:1969 | Fuse definitions |
| DIN VDE 0298-4 : 1998 | APPLICATION OF CABLES AND CORDS IN POWER INSTALLATIONS - PART 4: RECOMMENDED CURRENT-CARRYING CAPACITY FOR SHEATHED AND NONSHEATHED CABLES FOR FIXED WIRINGS IN AND AROUND BUILDINGS AND FOR FLEXIBLE CABLES AND CORDS |
| VDE 0820-2 : 2015 | MINIATURE FUSES - PART 2: CARTRIDGE FUSE-LINKS (IEC 60127-2:2014) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| HD 109 : 200S3 | MINIATURE FUSES FIRST SUPPLEMENT - COLOUR CODING |
| IEC 60364-3:1993 | Electrical installations of buildings - Part 3: Assessment of general characteristics |
| DIN 6730:2016-05 (Draft) | PAPER, BOARD AND PULPS - VOCABULARY |
| ISO 4046:1978 | Paper, board, pulp and related terms — Vocabulary |
| HD 365 : 200S3 | CLASSIFICATION OF DEGREES OF PROTECTION PROVIDED BY ENCLOSURES |
| VDE 0471-2-1 : 84 DRAFT 92 | FIRE HAZARD TESTING; TEST METHODS; GLOW WIRE TEST AND GUIDANCE |
| HD 444.2.1 : 200S1 | FIRE HAZARD TESTING - TEST METHODS - GLOW-WIRE TEST AND GUIDANCE |
| ISO 593:1974 | Paper Untrimmed stock sizes for the ISO-A Series ISO supplementary range |
| VDE 0820-100 : DRAFT 1978 | VDE SPECIFICATION FOR MINIATURE FUSES - STANDARD FOR FUSE HOLDERS |
| HD 384.3 : 200S2 | ELECTRICAL INSTALLATIONS OF BUILDINGS - ASSESSMENT OF GENERAL CHARACTERISTICS |
| IEC 60408:1985 | Low-voltage air-break switches, air-break disconnectors, air-break switch-disconnectors and fuse-combination units |
| HD 243 : S12 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS |
| DIN VDE 0105-1 : 1983 | OPERATION OF POWER INSTALLATIONS; GENERAL REQUIREMENTS |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| DIN IEC 60584-1:1984-01 | THERMOCOUPLES - PART 1: REFERENCE TABLES |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.