EEMUA 190 : 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GUIDE FOR THE DESIGN, CONSTRUCTION AND USE OF MOUNDED HORIZONTAL CYLINDRICAL VESSELS FOR PRESSURISED STORAGE OF LPG AT AMBIENT TEMPERATURE
English
01-01-2000
08-02-2021
FOREWORD
1 INTRODUCTION AND SCOPE
2 TYPES OF STORAGE VESSEL
3 FOUNDATION AND EARTH MOUND
4 VESSEL
5 VESSEL: INSPECTION, TESTING
AND CERTIFICATION
6 GUIDELINES FOR IN-SERVICE INSPECTION
7 REFERENCES
8 GLOSSARY OF ABBREVIATIONS
APPENDIX A - STRESS ANALYSIS OF MOUNDED
STORAGE VESSELS
APPENDIX B - TYPICAL DESIGN FEATURES FOR
VESSEL, FOUNDATION AND CONNECTIONS
APPENDIX C - DISTRIBUTION OF SOIL REACTION
(SUPPORTING LOAD)
APPENDIX D - RECOMMENDED STEEL GRADES
APPENDIX E - PROJECT PLANNING
APPENDIX F - DELETED
APPENDIX G - NON-DESTRUCTIVE TESTING REQUIREMENTS
APPENDIX H - MATERIAL HARDNESS TESTING
APPENDIX I - SELECTION OF STORAGE SYSTEM
Specifies the main requirements for the successful design, construction, installation and use of mounded storage steel vessels, including: - criteria for selecting mounded storage - soil survey - foundation and mound design - vessel design and fabrication - erection and construction - requirements for operability (fittings, instrumentation) - corrosion protection - inspection and testing and - in-service monitoring, inspection and maintenance.
| DevelopmentNote |
Reprinted 2017 incorporating all amendments and errata to date. (08/2017)
|
| DocumentType |
Standard
|
| Pages |
108
|
| PublisherName |
Engineering Equipment Material Users Association
|
| Status |
Superseded
|
| SupersededBy |
| EEMUA 147 : 2016 | RECOMMENDATIONS FOR REFRIGERATED LIQUEFIED GAS STORAGE TANKS |
| EEMUA 217 : 2011 | SAFE AND EFFECTIVE OPERATION OF STORAGE TANKS FOR OIL MOVEMENTS |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 9329-3:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 3: Unalloyed and alloyed steels with specified low temperature properties |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| ISO 2808:2007 | Paints and varnishes — Determination of film thickness |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| NACE RP 02 74 : 2004 | HIGH-VOLTAGE ELECTRICAL INSPECTION OF PIPELINE COATINGS |
| ASTM D 2167 : 2015 : REDLINE | Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method |
| EEMUA 159 : 2014 | ABOVE GROUND FLAT BOTTOMED STORAGE TANKS - A GUIDE TO INSPECTION, MAINTENANCE AND REPAIR |
| BS EN 1993-1-1 : 2005 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| BS 5400-3:1982 | Steel, concrete and composite bridges Code of practice for design of steel bridges |
| BS 6072:1981 | Method for magnetic particle flaw detection |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| BS 3923-2:1972 | Methods for ultrasonic examination of welds Automatic examination of fusion welded butt joints in ferritic steels |
| EEMUA 147 : 2016 | RECOMMENDATIONS FOR REFRIGERATED LIQUEFIED GAS STORAGE TANKS |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 1043-1:1995 | Destructive tests on welds in metallic materials - Hardness testing - Part 1: Hardness test on arc welded joints |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Important note : Users cannot be edited or removed once added to your Multi user PDF.