EN 12897:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Water supply - Specification for indirectly heated unvented (closed) storage water heaters
Superseded date
12-02-2020
Superseded by
Published date
15-06-2016
Publisher
Sorry this product is not available in your region.
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Requirements
5 Marking
6 Evaluation of conformity
7 Technical documents
Annex A (normative) - Hot water safety and performance
testing
Annex B (normative) - Measurement of standing heat loss
for factory insulated storage water heaters
Annex C (informative) - Inspection access
Annex ZA (informative) - Relationship between this
European Standard and the requirements of Commission
Delegated Regulation (EU) No 812/2013 of February 2013
supplementing Directive 2010/30/EU regarding energy
labelling for water heaters and hot water storage tanks
Annex ZB (informative) - Relationship between this European
Standard and the requirements of Commission Regulation
(EU) No 814/2013 of 2 August 2013 implementing Directive
2009/125/EC with regard to Ecodesign requirements for
water heaters and hot water storage tanks
Bibliography
This European Standard specifies the constructional and performance requirements and methods of test for indirectly heated, unvented (closed) storage water heaters of up to 2 000 l volume suitable for connection to a water supply at a pressure between 0,05 MPa and 1,0 MPa (0,5 bar and 10 bar), and fitted with control and safety devices designed to prevent the temperature of the stored drinking water from reaching 95 °C.Whilst storage water heaters intended primarily for direct heating are not covered by this standard, it does allow the provision of electric heating elements for auxiliary use.
| Committee |
CEN/TC 164
|
| DevelopmentNote |
Supersedes PREN 12897. (06/2016)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 12897:2016-12 | Identical |
| NBN EN 12897 : 2016 | Identical |
| DIN EN 12897:2006-09 | Identical |
| BS EN 12897:2016 | Identical |
| UNE-EN 12897:2017 | Identical |
| I.S. EN 12897:2016 | Identical |
| PN EN 12897 : 2016 | Identical |
| NEN EN 12897 : 2016 | Identical |
| SN EN 12897 : 2016 | Identical |
| NF EN 12897 : 2016 | Identical |
| NS EN 12897 : 2006 | Identical |
| UNI EN 12897 : 2007 | Identical |
| ONORM EN 12897 : 2016 | Identical |
| UNI EN 12977-4 : 2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| UNI CEN/TS 12977-4 : 2010 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| NF EN 806-5 : 2012 | SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE |
| I.S. EN 15332:2007 | HEATING BOILERS - ENERGY ASSESSMENT OF HOT WATER STORAGE SYSTEMS |
| CEN/TS 12977-4:2010 | Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores |
| EN 12831-3:2017 | Energy performance of buildings - Method for calculation of the design heat load - Part 3: Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3 |
| DIN EN 12976-1:2017-04 | Thermal solar systems and components - Factory made systems - Part 1: General requirements |
| 11/30247846 DC : 0 | BS EN 12977-4 - THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| PREN 15332 : DRAFT 2017 | HEATING BOILERS - ENERGY ASSESSMENT OF HOT WATER STORAGE SYSTEMS |
| I.S. EN 12977-4:2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| DIN EN 15316-3-3:2008-06 | HEATING SYSTEMS IN BUILDINGS - METHOD FOR CALCULATION OF SYSTEM ENERGY REQUIREMENTS AND SYSTEM EFFICIENCIES - PART 3-3: DOMESTIC HOT WATER SYSTEMS, GENERATION |
| BS EN 15316-3-3:2007 | Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies Domestic hot water systems, generation |
| I.S. EN 12977-2:2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 2: TEST METHODS FOR SOLAR WATER HEATERS AND COMBISYSTEMS |
| DIN EN 12977-3:2016-08 (Draft) | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 3: PERFORMANCE TEST METHODS FOR SOLAR WATER HEATER STORES |
| BS EN 12977-4:2012 | Thermal solar systems and components. Custom built systems Performance test methods for solar combistores |
| DIN EN 15332:2008-01 | HEATING BOILERS - ENERGY ASSESSMENT OF HOT WATER STORAGE SYSTEMS |
| I.S. EN 12976-1:2017 | THERMAL SOLAR SYSTEMS AND COMPONENTS - FACTORY MADE SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| VDI 3805 Blatt 20:2017-02 | Product data exchange in the building services - Storage tanks and instantaneous water heater |
| DIN EN 12831-3:2017-09 | ENERGY PERFORMANCE OF BUILDINGS - METHOD FOR CALCULATION OF THE DESIGN HEAT LOAD - PART 3: DOMESTIC HOT WATER SYSTEMS HEAT LOAD AND CHARACTERISATION OF NEEDS, MODULE M8-2, M8-3 |
| BS EN 12977-3:2012 | Thermal solar systems and components. Custom built systems Performance test methods for solar water heater stores |
| 11/30247855 DC : 0 | BS EN 12977-3 - THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 3: PERFORMANCE TEST METHODS FOR SOLAR WATER HEATER STORES |
| I.S. EN 12831-3:2017 | ENERGY PERFORMANCE OF BUILDINGS - METHOD FOR CALCULATION OF THE DESIGN HEAT LOAD - PART 3: DOMESTIC HOT WATER SYSTEMS HEAT LOAD AND CHARACTERISATION OF NEEDS, MODULE M8-2, M8-3 |
| EN 12977-2:2018 | Thermal solar systems and components - Custom built systems - Part 2: Test methods for solar water heaters and combisystems |
| EN 12977-1:2018 | Thermal solar systems and components - Custom built systems - Part 1: General requirements for solar water heaters and combisystems |
| UNE-EN 12977-3:2012 | Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores |
| DIN EN 12976-1:2014-07 (Draft) | THERMAL SOLAR SYSTEMS AND COMPONENTS - FACTORY MADE SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| EN 12976-1:2017 | Thermal solar systems and components - Factory made systems - Part 1: General requirements |
| DIN EN 806-5:2012-04 | Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance |
| BS EN 806-5:2012 | Specifications for installations inside buildings conveying water for human consumption Operation and maintenance |
| 09/30200073 DC : 0 | BS EN 806-5 - SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE |
| DD CEN/TS 12977-4 : DRAFT MAY 2010 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| 14/30311710 DC : 0 | BS EN 12831-3 - HEATING SYSTEMS AND WATER BASED COOLING SYSTEMS IN BUILDINGS - METHOD FOR CALCULATION OF THE DESIGN HEAT LOAD - PART 3: DOMESTIC HOT WATER SYSTEMS HEAT LOAD AND CHARACTERISATION OF NEEDS |
| 17/30348435 DC : 0 | BS EN 15332 - HEATING BOILERS - ENERGY ASSESSMENT OF HOT WATER STORAGE SYSTEMS |
| I.S. EN 15316-3-3:2007 | HEATING SYSTEMS IN BUILDINGS - METHOD FOR CALCULATION OF SYSTEM ENERGY REQUIREMENTS AND SYSTEM EFFICIENCIES - PART 3-3: DOMESTIC HOT WATER SYSTEMS, GENERATION |
| EN 12977-4:2018 | Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores |
| PREN 12977-3 : DRAFT 2011 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 3: PERFORMANCE TEST METHODS FOR SOLAR WATER HEATER STORES |
| EN 12977-3:2018 | Thermal solar systems and components - Custom built systems - Part 3: Performance test methods for solar water heater stores |
| BS EN 12976-1:2017 | Thermal solar systems and components. Factory made systems General requirements |
| BS EN 15332:2007 | Heating boilers. Energy assessment of hot water storage systems |
| EN 15316-3-3:2007 | Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 3-3: Domestic hot water systems, generation |
| EN 15332:2007 | Heating boilers - Energy assessment of hot water storage systems |
| EN 806-5:2012 | Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance |
| BS EN 12977-1:2012 | Thermal solar systems and components. Custom built systems General requirements for solar water heaters and combisystems |
| DIN EN 12977-4:2016-08 (Draft) | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| BS EN 12831-3:2017 | Energy performance of buildings. Method for calculation of the design heat load Domestic hot water systems heat load and characterisation of needs, Module M8-2, M8-3 |
| UNI EN 806-5 : 2012 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE |
| I.S. EN 806-5:2012 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 5: OPERATION AND MAINTENANCE |
| I.S. EN 12977-3:2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 3: PERFORMANCE TEST METHODS FOR SOLAR WATER HEATER STORES |
| I.S. EN 12977-1:2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 1: GENERAL REQUIREMENTS FOR SOLAR WATER HEATERS AND COMBISYSTEMS |
| S.R. CEN TS 12977-4:2010 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 4: PERFORMANCE TEST METHODS FOR SOLAR COMBISTORES |
| UNE-EN 806-5:2013 | Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance |
| UNE-EN 12977-4:2012 | Thermal solar systems and components - Custom built systems - Part 4: Performance test methods for solar combistores |
| UNI EN 12977-3 : 2012 | THERMAL SOLAR SYSTEMS AND COMPONENTS - CUSTOM BUILT SYSTEMS - PART 3: PERFORMANCE TEST METHODS FOR SOLAR WATER HEATER STORES |
| IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
| EN 15332:2007 | Heating boilers - Energy assessment of hot water storage systems |
| EN 1490:2000 | Building valves - Combined temperature and pressure relief valves - Tests and requirements |
| EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 1567:1999 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| IEC 60379:1987 | Methods for measuring the performance of electric storage water-heaters for household purposes |
| EN 1491:2000 | Building valves - Expansion valves - Tests and requirements |
| EN 1488:2000 | Building valves - Expansion groups - Tests and requirements |
| EN 1487:2014 | Building valves - Hydraulic safety groups - Tests and requirements |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 1489:2000 | Building valves - Pressure safety valves - Tests and requirements |
| EN 13959:2004 | Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 60379:2004 | Methods for measuring the performance of electric storage water-heaters for household purposes |
| 2009/125/EC : 2009 AMD 1 2012 | DIRECTIVE 2009/125/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 21 OCTOBER 2009 ESTABLISHING A FRAMEWORK FOR THE SETTING OF ECODESIGN REQUIREMENTS FOR ENERGY-RELATED PRODUCTS (RECAST) (TEXT WITH EEA RELEVANCE) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.