EN 12957:2001+A1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Machine tools - Safety - Electro discharge machines
01-08-2013
11-02-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 General requirements
5.2 Operating modes
5.3 Stop functions
5.4 Safety related parts of control systems for EDM
equipment or EDM systems
5.5 Specific requirements
6 Verification of safety requirements and/or measures
7 Information for use
7.1 General
7.2 Markings, signs, written warnings
7.3 Instruction handbook
Annex A (informative) - Examples and schematic pictures
Annex B (normative) - Noise emission measurements
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 97/37/EC, amended by Directive 98/79/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
1.1This standard specifies technical safety requirements and measures, applicable to EDM equipment and EDM system (e.g. for spark erosion-sinking, spark erosion-wire cutting), to be adopted by persons undertaking the design, construction, installation and/or supply of such equipment. This standard also includes information to be provided by the manufacturer to the user.1.2The design requirements of this standard shall not apply to arc eroding and electro chemical machining equipment.1.3This standard takes account of the intended use in normal workshop environment and non explosive atmospheres including installation, setting, maintenance, repair and dismantling for removal or disposal of EDM equipment.1.4This standard also applies to auxiliary devices essential for EDM processing.1.5This standard deals with specific hazards defined in clause 4, Table 1, and the measures of prevention in clause 5, Table 2.1.6This standard applies to machines built after its date of issue.NOTEDirective 94/9/EC concerning equipment and protective systems intended for use in potentially explosive atmospheres can be applicable to the type of machine or equipment covered by this European Standard. The present standard is not intended to provide means of complying with the essential health and safety requirements of Directive 94/9/EC.
| Committee |
CEN/TC 143
|
| DevelopmentNote |
2001 Edition Re-Issued in February 2009 & incorporates AMD 1 2009. (03/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 12957:2001-12 | Identical |
| PN EN 12957 : 2003 + A1 2009 | Identical |
| NS EN 12957 : 2001 + A1 2009 | Identical |
| GOST EN 12957 : 2011 | Identical |
| BS EN 12957 : 2001 | Identical |
| NEN EN 12957 : 2001 + A1 2009 | Identical |
| UNE-EN 12957:2002 | Identical |
| SN EN 12957 : 2001 + A1 2009 | Identical |
| DIN EN 12957:2009-07 | Identical |
| UNI EN 12957 : 2009 | Identical |
| NBN EN 12957 : 2001 + A1 2009 | Identical |
| NF EN 12957 : 2001 + A1 2009 | Identical |
| I.S. EN 12957:2001 | Identical |
| UNE-EN 12957:2002+A1:2009 | Identical |
| I.S. EN 14070:2003 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| DIN EN 14070:2009-07 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| UNI EN 14070 : 2009 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| BS EN 14070 : 2003 | SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES |
| 09/30202313 DC : 0 | BS EN 12514-3 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 3: SAFETY REQUIREMENTS AND TESTS - VALVES AND METERS |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN 418 : 1992 | SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| IEC 61000-6-2:2016 | Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 10218:1992 | Manipulating industrial robots Safety |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| EN 60742:1995 | Isolating transformers and safety isolating transformers - Requirements |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 61000-6-2:2005/corrigendum:2005 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS (IEC 61000-6-2:2005) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| EN 54-1:2011 | Fire detection and fire alarm systems - Part 1: Introduction |
| EN 775:1992/AC:1993 | MANIPULATING INDUSTRIAL ROBOTS - SAFETY |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.