EN 13677-3:2003
Current
The latest, up-to-date edition.
Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements
12-02-2003
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Specification
4.1 Obligatory specified parameters
4.2 Optional specified parameters
Bibliography
1.1This Part 3 of prEN 13677, is a specification for thermoplastic compression mouldable sheet consisting of textile glass mat reinforced polypropylene or equivalent products, as described in Part 1 of this specification.The specification defines those parameters which shall be specified plus other parameters which may be specified if required for a particular application or processing method.1.2The specification does not define absolute or nominal values for any parameter. The value of a specified parameter is to be defined by the manufacturer, but this specification defines the method of test to be used to determine the value of each specified parameter and the tolerance about which the parameter shall be controlled by the manufacturer.1.3The parameters to be defined in any GMT specification are defined in 4.1. Parameters to be specified are those, which should typically appear on data sheets. Only a selection of these parameters should be included on the certificate of conformity. The other parameters which are included in a specification should either be nominated by the manufacturer, or agreed between manufacturer and customer. These parameters are defined in 4.2.1.4A selection of the specified parameters should be used for quality control purposes to check the conformity. The specification defines which parameters should be used for checking the conformity of the material. These parameters are defined as part of 4.1. Other specified parameters may be included if critical for a particular application or processing method. This is to be agreed between manufacturer and customer of a production lot and will be reported in the certificate of conformity, which should be in accordance with EN 10204.
Committee |
CEN/TC 249
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
NEN EN 13677-3 : 2003 | Identical |
NF EN 13677-3 : 2003 | Identical |
DIN EN 13677-3:2003-07 | Identical |
UNE-EN 13677-3:2003 | Identical |
I.S. EN 13677-3:2003 | Identical |
PN EN 13677-3 : 2005 | Identical |
NS EN 13677-3 : 1ED 2003 | Identical |
BS EN 13677-3:2003 | Identical |
NBN EN 13677-3 : 2003 | Identical |
UNI EN 13677-3 : 2003 | Identical |
SN EN 13677-3 : 2003 | Identical |
14/30273514 DC : 0 | BS ISO 18249 - NON-DESTRUCTIVE TESTING - ACOUSTIC EMISSION TESTING - TESTING OF FIBRE REINFORCED POLYMERS - SPECIFIC METHODOLOGY AND GENERAL EVALUATION CRITERIA |
BS ISO 18249:2015 | Non-destructive testing. Acoustic emission testing. Specific methodology and general evaluation criteria for testing of fibre-reinforced polymers |
ISO 18249:2015 | Non-destructive testing Acoustic emission testing Specific methodology and general evaluation criteria for testing of fibre-reinforced polymers |
IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
ISO 6721-2:2008 | Plastics Determination of dynamic mechanical properties Part 2: Torsion-pendulum method |
ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
EN ISO 6721-2:2008 | Plastics - Determination of dynamic mechanical properties - Part 2: Torsion-pendulum method (ISO 6721-2:2008) |
EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
ISO 1172:1996 | Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods |
ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
ISO 472:2013 | Plastics — Vocabulary |
ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
EN ISO 6603-2:2000 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000) |
EN ISO 11403-2:2012 | Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012) |
EN 10204:2004 | Metallic products - Types of inspection documents |
EN ISO 1172:1998 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996) |
ISO 62:2008 | Plastics Determination of water absorption |
ISO 14126:1999 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction |
ISO 178:2010 | Plastics Determination of flexural properties |
EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.