EN 15632-3:2010+A1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes; requirements and test methods
03-06-2022
17-12-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Test procedures
Annex A (informative) - Application of
Miner's Rule
This European Standard provides requirements and test methods for flexible, pre-insulated, direct buried district heating pipes with plastic service pipes and no bonding between the layers of the pipes.This European Standard is valid for maximum operating temperatures of 95 °C and maximum operating pressures up to 10 bar for a design lifetime of at least 30 years.This European Standard does not cover surveillance systems.NOTEFor higher temperatures or for the transport of other fluids, for example potable water, additional requirements and testing is needed. Such requirements are not specified in this European Standard.
| Committee |
CEN/TC 107
|
| DevelopmentNote |
2010 Edition Re-Issued in December 2014 & incorporates AMD 1 2014. (01/2015)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| UNI EN 15632-3:2015 | Identical |
| ONORM EN 15632-3 : 2015 | Identical |
| UNI EN 15632-3 : 2010 | Identical |
| NBN EN 15632-3 : 2010 + A1 2015 | Identical |
| NF EN 15632-3 : 2010 + A1 2015 | Identical |
| I.S. EN 15632-3:2010 | Identical |
| SN EN 15632-3 : 2010 + A1 2015 | Identical |
| BS EN 15632-3 : 2010 | Identical |
| NS EN 15632-3 : 2010 + A1 2014 | Identical |
| PN EN 15632-3 : 2010 + A1 2015 | Identical |
| DIN EN 15632-3:2015-03 | Identical |
| NEN EN 15632-3 : 2010 + A1 2014 | Identical |
| BS EN 15632-3:2010+A1:2014 | Identical |
| UNE-EN 15632-3:2010+A1:2014 | Identical |
| EN ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings (ISO 15875-3:2003) |
| EN 15632-2:2010+A1:2014 | District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods |
| EN ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017) |
| ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| EN 15632-1:2009+A1:2014 | District heating pipes - Pre-insulated flexible pipe systems - Part 1: Classification, general requirements and test methods |
| ISO 15875-2:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes |
| EN ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017) |
| EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
| ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| EN ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 1: General (ISO 15876-1:2017) |
| EN ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure - Miner's rule - Calculation method for cumulative damage (ISO 13760:1998) |
| EN ISO 15875-5:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003) |
| EN ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 3: Fittings (ISO 15876-3:2017) |
| ISO 17455:2005 | Plastics piping systems Multilayer pipes Determination of the oxygen permeability of the barrier pipe |
| ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| ISO 15875-1:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General |
| ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings |
| ISO 13760:1998 | Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage |
| ISO 10147:2011 | Pipes and fittings made of crosslinked polyethylene (PE-X) Estimation of the degree of crosslinking by determination of the gel content |
| ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.