![header thumbnail](/images/img-default-logo.png)
EN 1804-3:2006+A1:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/img-default-logo.png)
Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems
12-01-2021
27-01-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements
6 Verification of the safety requirements
7 User Information
Annex A (normative) Tests for verification of the safety
requirements
Annex B (normative) Deviations from EN 982:1996
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of the
EU Directive 2006/42/EC
Bibliography
This document specifies the safety requirements for hydraulic control devices, including hydraulic valves and their control elements, valve combi¬nations, control systems, pipes and hose assemblies, fittings, shut-off devices, measuring devices, filters, built-in pressure limiting and check valves in legs and rams and water spraying and dust suppression valves when used as specified by the manufacturer or his authorized representative. Excluded are electronic control devices, pressure generators, and internal valves of legs and rams (e.g. constant yield valves, see EN1804-2).Some components are dealt with in other parts of this standard.NOTEprEN1804-4 also applies to electro-hydraulic control devices. Part 4 also contains requirements for electrical control elements of valves.This document applies to hydraulic control devices at ambient temperatures from –10 °C to 60 °C.This document identifies and takes into account:-possible hazards which may be caused by the operation of hydraulic control devices;-areas and operating conditions which may create such hazards;-hazardous situations which may cause injury or may be damaging to health;-hazards which may be caused by firedamp and/or combustible dusts.This document describes methods for the reduction of these hazards.A list of significant hazards covered appears in clause 4.This document is applicable to all hydraulic control devices placed on the market for the first time after the date of issue of this standard.This document does not specify any additional requirements for:-use in particularly corrosive environments;-hazards occurring during construction, transportation, decommissioning;-earthquakes.
DevelopmentNote |
2006 Edition Re-issued in January 2010 & incorporates AMD 1 2010. (02/2010)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
UNI EN 1804-3 : 2010 | Identical |
PN EN 1804-3 : 2008 + A1 2012 | Identical |
NF EN 1804-3 : 2006 + A1 2010 | Identical |
I.S. EN 1804-3:2006 | Identical |
UNE-EN 1804-3:2007 | Identical |
BS EN 1804-3 : 2006 | Identical |
NBN EN 1804-3 : 2006 + A1 2010 | Identical |
NEN EN 1804-3 : 2006 + A1 2010 | Identical |
SN EN 1804-3 : 2006 + A1 2010 | Identical |
DIN EN 1804-3:2010-05 | Identical |
NS EN 1804-3 : 2006 + A1 2010 | Identical |
UNE-EN 1804-3:2007+A1:2010 | Identical |
BS EN 1804-3:2006+A1:2010 | Identical |
12/30243465 DC : 0 | BS ISO/IEC 80079-38 - EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
ISO/IEC 80079-38:2016 | Explosive atmospheres Part 38: Equipment and components in explosive atmospheres in underground mines |
DIN EN ISO/IEC 80079-38:2012-08 (Draft) | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079-38:2016) |
BS EN ISO/IEC 80079-38 : 2016 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079 38:2016) |
NF EN 1804-2 : 2002 + A1 2010 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 2: POWER SET LEGS AND RAMS |
DIN EN 1804-1:2010-05 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements (includes Amendment A1:2010) |
DIN EN 1804-2:2010-05 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams (includes Amendment A1:2010) |
UNI EN 1804-2 : 2010 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 2: POWER SET LEGS AND RAMS |
EN 1804-2:2001+A1:2010 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams |
I.S. EN 1804-1:2002 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 1: SUPPORT UNITS AND GENERAL REQUIREMENTS |
I.S. EN 1804-2:2002 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 2: POWER SET LEGS AND RAMS |
EN 1804-1:2001+A1:2010 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements |
UNI EN 1804-1 : 2010 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 1: SUPPORT UNITS AND GENERAL REQUIREMENTS |
EN ISO/IEC 80079-38:2016 | Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines (ISO/IEC 80079-38:2016) |
DIN EN 1710:2008-08 | EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
BS EN 1804-1 : 2001 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 1: SUPPORT UNITS AND GENERAL REQUIREMENTS |
UNI EN 1710 : 2008 | EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
DIN EN ISO/IEC 80079-38 E : 2017 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC 80079-38:2016) |
04/19986707 DC : 0 | BS EN 1804-4 - MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 4: ELECTRO-HYDRAULIC CONTROL SYSTEMS |
I.S. EN ISO/IEC 80079-38:2016 | EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES (ISO/IEC/DIS 80079-38:2012) |
NF EN 1804-1 : 2002 + A1 2010 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 1: SUPPORT UNITS AND GENERAL REQUIREMENTS |
BS EN 1710 : 2005 | EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
EN 1710:2005+A1:2008/AC:2010 | EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES |
BS EN 1804-2 : 2001 | MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 2: POWER SET LEGS AND RAMS |
UNE-EN 1804-1:2003 | Machines for underground mines. Safety requirements for hydraulic powered roof supports. Part 1: Support units and general requiremetns. |
UNE-EN 1804-2:2003 | Machines for underground mines. Safety requirements for hydraulic powered roof supports. Part 2: Power set legs and rams. |
EN 854:2015 | Rubber hoses and hose assemblies - Textile reinforced hydraulic type - Specification |
EN 856:2015 | Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced hydraulic type - Specification |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
EN 1804-1:2001+A1:2010 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 1: Support units and general requirements |
EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
EN 857:2015 | Rubber hoses and hose assemblies - Wire braid reinforced compact type for hydraulic applications - Specification |
EN 1804-2:2001+A1:2010 | Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 2: Power set legs and rams |
EN ISO 12100-1:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY |
IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
EN ISO 12100-2:2003/A1:2009 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES |
ISO 1219-1:2012 | Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications |
EN ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015) |
ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
EN 855 : 1996 | PLASTICS HOSES AND HOSE ASSEMBLIES - THERMOPLASTICS TEXTILE REINFORCED HYDRAULIC TYPE - SPECIFICATION |
EN 853:2015 | Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type - Specification |
ISO 4021:1992 | Hydraulic fluid power — Particulate contamination analysis — Extraction of fluid samples from lines of an operating system |
ISO 6805:1994 | Rubber hoses and hose assemblies for underground mining Wire-reinforced hydraulic types for coal mining Specification |
ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) |
ISO 7745:2010 | Hydraulic fluid power — Fire-resistant (FR) fluids — Requirements and guidelines for use |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.