EN 61223-3-5:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Evaluation and routine testing in medical imaging departments - Part 3-5: Acceptance tests - Imaging performance of computed tomography X-ray equipment
02-02-2022
23-09-2004
FOREWORD
INTRODUCTION
1 Scope and object
2 Normative references
3 Terms and definitions
4 General aspects of ACCEPTANCE TESTS
5 Test methods for CT SCANNERS
Annex A (normative) - Terminology - Index of defined terms
Annex B (informative) - Recommended criteria for test results
Annex C (informative) - Visual Method for LOW CONTRAST RESOLUTION
Annex D (informative) - Accuracy of the gantry tilt
Annex E (informative) - DOSE PROFILE
Annex F (informative) - Alternate test methods for
SPATIAL RESOLUTION
Annex G (informative) - TOMOGRAPHIC SECTION
THICKNESS for helical scanning
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
This standard - defines the essential parameters which describe the performance of the CT scanners with regard to image quality, patient dose and positioning; - defines the methods of testing the essential parameters; - evaluates compliance with the tolerances of the parameters specified by the accompanying documents. These methods rely mainly on non-invasive measurements, using appropriate test equipment, performed during the installation or after it has been completed. Signed statements covering steps in the installation procedure may be used as part of the acceptance test report. This part of EN 61223 is intended to assist in performing the acceptance tests on a CT scanner. The aim is to verify compliance of the installation with specifications affecting the image quality, patient dose and positioning.
| Committee |
CLC/TC 62
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| OVE/ONORM EN 61223-3-5 : 2005 | Identical |
| DIN EN 61223-3-5:2005-08 | Identical |
| NF EN 61223-3-5 : 2005 | Identical |
| IEC 61223-3-5:2004 | Identical |
| NBN EN 61223 3-5 : 2006 | Identical |
| NEN EN IEC 61223-3-5 : 2004 C1 2006 | Identical |
| I.S. EN 61223-3-5:2004 | Identical |
| PN EN 61223-3-5 : 2005 | Identical |
| BS EN 61223-3-5:2004 | Identical |
| UNE-EN 61223-3-5:2005 | Identical |
| CEI EN 61223-3-5 : 2005 | Identical |
| I.S. EN 61223-2-6:2007 | EVALUATION AND ROUTINE TESTING IN MEDICAL IMAGING DEPARTMENTS - PART 2-6: CONSTANCY TESTS - IMAGING PERFORMANCE OF COMPUTED TOMOGRAPHY X-RAY EQUIPMENT |
| BS EN 60601-2-68:2015 | Medical electrical equipment Particular requirements for the basic safety and essential performance of X-ray-based image-guided radiotherapy equipment for use with electron accelerators, light ion beam therapy equipment and radionuclide beam therapy equipment |
| UNE-EN 60601-2-44:2010 | Medical electrical equipment -- Part 2-44: Particular requirements for the basic safety and essential performance of X-ray equipment for computed tomography |
| EN 60601-2-68:2015 | Medical electrical equipment - Part 2-68: Particular requirements for the basic safety and essential performance of X-ray-based image-guided radiotherapy equipment for use with electron accelerators, light ion beam therapy equipment and radionuclide beam therapy equipment |
| I.S. EN 60601-2-44:2009 | MEDICAL ELECTRICAL EQUIPMENT - PART 2-44: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF X-RAY EQUIPMENT FOR COMPUTED TOMOGRAPHY |
| EN 60601-2-44:2009/A2:2016 | MEDICAL ELECTRICAL EQUIPMENT - PART 2-44: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF X-RAY EQUIPMENT FOR COMPUTED TOMOGRAPHY (IEC 60601-2-44:2009/A2:2016) |
| BS EN 61223-2-6:2007 | Evaluation and routine testing in medical imaging departments Constancy tests. Imaging performance of computed tomography X-ray equipment |
| BS EN 60601-2-44 : 2009 | MEDICAL ELECTRICAL EQUIPMENT - PART 2-44: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF X-RAY EQUIPMENT FOR COMPUTED TOMOGRAPHY (IEC 60601-2-44:2009) |
| I.S. EN 60601-2-68:2015 | MEDICAL ELECTRICAL EQUIPMENT - PART 2-68: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF X-RAY-BASED IMAGE-GUIDED RADIOTHERAPY EQUIPMENT FOR USE WITH ELECTRON ACCELERATORS, LIGHT ION BEAM THERAPY EQUIPMENT AND RADIONUCLIDE BEAM THERAPY EQUIPMENT |
| EN 61223-2-6:2007 | Evaluation and routine testing in medical imaging departments - Part 2-6: Constancy tests - Imaging performance of computed tomography X-ray equipment |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| IEC 60336:2005 | Medical electrical equipment - X-ray tube assemblies for medical diagnosis - Characteristics of focal spots |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| IEC 60522:1999 | Determination of the permanent filtration of X-ray tube assemblies |
| ISO 5725-3:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method |
| ISO 5725-6:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values |
| ISO 5725-4:1994 | Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method |
| ISO 2092:1981 | Light metals and their alloys Code of designation based on chemical symbols |
| IEC 60601-2-28:2017 | Medical electrical equipment - Part 2-28: Particular requirements for the basic safety and essential performance of X-ray tube assemblies for medical diagnosis |
| IEC 60601-2-32:1994 | Medical electrical equipment - Part 2: Particular requirements for the safety of associated equipment of X-ray equipment |
| ASTM E 1695 : 1995 | Standard Test Method for Measurement of Computed Tomography (CT) System Performance |
| IEC 61223-2-6:2006 | Evaluation and routine testing in medical imaging departments - Part 2-6: Constancy tests imaging performance of computed tomography X-ray equipment |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| IEC 61223-2-4:1994 | Evaluation and routine testing in medical imaging departments - Part 2-4: Constancy tests - Hard copy cameras |
| IEC 61267:2005 | Medical diagnostic X-ray equipment - Radiation conditions for use in the determination of characteristics |
| EN 60601-2-44:2009/A2:2016 | MEDICAL ELECTRICAL EQUIPMENT - PART 2-44: PARTICULAR REQUIREMENTS FOR THE BASIC SAFETY AND ESSENTIAL PERFORMANCE OF X-RAY EQUIPMENT FOR COMPUTED TOMOGRAPHY (IEC 60601-2-44:2009/A2:2016) |
| IEC 60601-2-44:2009+AMD1:2012+AMD2:2016 CSV | Medical electrical equipment - Part 2-44: Particular requirements for the basic safety and essential performance of X-ray equipment for computed tomography |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.