EN ISO 12215-9:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Small craft - Hull construction and scantlings - Part 9: Sailing craft appendages (ISO 12215-9:2012)
23-03-2022
15-06-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Design stresses
6 Structural components to be assessed
7 Load cases
8 Computational methods
9 Compliance
Annex A (normative) - Application declaration
Annex B (informative) - Information on metal for appendages
and fasteners and "established practice" for
fastening and welding
Annex C (informative) - "Established practice" structural
arrangement for ballast keels
Annex D (informative) - "Established practice" calculation
of keel fin strength (fixed or canting) and fixed
ballast keel connected by bolts
Annex E (informative) - Geometrical properties of some typical
appendage foil shapes
Annex F (informative) - Simplified fatigue strength assessment
Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 94/25/EC as amended by Directive 2003/44/EC
ISO 12215-9:2011 defines the loads and specifies the scantlings of sailing craft appendages on monohull sailing craft with a length of hull of up to 24 m, measured according to ISO 8666. It gives design stresses, the structural components to be assessed, load cases and design loads for keel, centreboard and their attachments, computational methods and modelling guidance, and the means for compliance with its provisions.
| Committee |
CEN/BT
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN ISO 12215-9 : 2012 | Identical |
| SN EN ISO 12215-9 : 2012 | Identical |
| NF EN ISO 12215-9 : 2012 | Identical |
| PN EN ISO 12215-9 : 2012 | Identical |
| UNE-EN ISO 12215-9:2013 | Identical |
| NS EN ISO 12215-9 : 2012 | Identical |
| NS-EN ISO 12215-9:2018 | Identical |
| UNI EN ISO 12215-9 : 2012 | Identical |
| PN-EN ISO 12215-9:2018-12 | Identical |
| I.S. EN ISO 12215-9:2018 | Identical |
| UNI EN ISO 12215-9:2018 | Identical |
| ISO 12215-9:2012 | Identical |
| BS EN ISO 12215-9:2012 | Identical |
| DIN EN ISO 12215-9:2013-01 | Identical |
| ONORM EN ISO 12215-9 : 2013 | Identical |
| BS EN ISO 12215-9:2018 | Identical |
| DIN EN ISO 12215-9:2019-02 | Identical |
| NEN-EN-ISO 12215-9:2018 en | Identical |
| NEN EN ISO 12215-9 : 2012 | Identical |
| ÖNORM EN ISO 12215-9 : 2019 04 15 | Identical |
| I.S. EN ISO 12215-9:2012 | Identical |
| 2003/44/EC : 2003 COR 1 2006 | DIRECTIVE 2003/44/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 2003 AMENDING DIRECTIVE 94/25/EC ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT |
| ISO 12215-5:2008 | Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 16143-2:2014 | Stainless steels for general purposes — Part 2: Corrosion-resistant semi-finished products, bars, rods and sections |
| GL I-1-1 : JAN 2016 | RULES FOR CLASSIFICATION AND CONSTRUCTION - 1: SHIP TECHNOLOGY - PART 1: SEAGOING SHIPS - CHAPTER 1: HULL STRUCTURES |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 12217-2:2015 | Small craft — Stability and buoyancy assessment and categorization — Part 2: Sailing boats of hull length greater than or equal to 6 m |
| 1994/25/EC : 1994 | DIRECTIVE 94/25/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 16 JUNE 1994 ON THE APPROXIMATION OF THE LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO RECREATIONAL CRAFT |
| ISO 8666:2016 | Small craft Principal data |
| NFE 25 030-1 : 2014 | FASTENERS - THREADED CONNECTIONS WITH ISO METRIC THREAD - PART 1: DESIGN RULES FOR TENSILE LOADED BOLTED JOINTS - SIMPLIFIED PROCEDURE - FIXATIONS |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| ISO 12215-3:2002 | Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| ISO 12215-6:2008 | Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| ABS 0037 : 1994 COR 2012 | GUIDE FOR BUILDING AND CLASSING OFFSHORE RACING YACHTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.