EN ISO 15118-3:2016
Current
The latest, up-to-date edition.
Road vehicles - Vehicle to grid Communication interface - Part 3: Physical and data link layer requirements (ISO 15118-3:2015)
20-04-2016
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Conventions
6 System architecture
7 Connection coordination
8 Timings and constants
9 Matching EV - EVSE process
10 EMC requirements
11 Signal coupling
12 Layer 2 interfaces
Annex A (normative) - HomePlug Green PHY on control
pilot line
Annex B (informative) - IEEE 1901.2 G3-PLC profile on
control pilot line
Bibliography
ISO 15118-3:2015 specifies the requirements of the physical and data link layer for a high-level communication, directly between battery electric vehicles (BEV) or plug-in hybrid electric vehicles (PHEV), termed as EV (electric vehicle) [ISO-1], based on a wired communication technology and the fixed electrical charging installation [Electric Vehicle Supply Equipment (EVSE)] used in addition to the basic signalling, as defined in [IEC-1].It covers the overall information exchange between all actors involved in the electrical energy exchange. ISO 15118 (all parts) is applicable for manually connected conductive charging.Only "[IEC-1] modes 3 and 4" EVSEs, with a high-level communication module, are covered by this part of ISO 15118.
| Committee |
CEN/TC 301
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| DIN EN ISO 15118-3:2016-08 | Identical |
| BS EN ISO 15118-3:2016 | Identical |
| NEN EN ISO 15118-3 : 2016 | Identical |
| NBN EN ISO 15118-3 : 2016 | Identical |
| PN EN ISO 15118-3 : 2016 | Identical |
| UNE-EN ISO 15118-3:2016 | Identical |
| NS EN ISO 15118-3 : 2016 | Identical |
| UNI EN ISO 15118-3 : 2016 | Identical |
| I.S. EN ISO 15118-3:2016 | Identical |
| ISO 15118-3:2015 | Identical |
| SN EN ISO 15118-3 : 2016 | Identical |
| PNE-EN ISO 15118-3 | Identical |
| IEC 62196-2:2016 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories |
| IEC TS 62763:2013 | Pilot function through a control pilot circuit using PWM (pulse width modulation) and a control pilot wire |
| IEC 62196-3:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 3: Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers |
| ISO 15118-1:2013 | Road vehicles Vehicle to grid communication interface Part 1: General information and use-case definition |
| ISO 15118-2:2014 | Road vehicles — Vehicle-to-Grid Communication Interface — Part 2: Network and application protocol requirements |
| IEC 61851-1:2017 | Electric vehicle conductive charging system - Part 1: General requirements |
| IEC 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.