• Shopping Cart
    There are no items in your cart

EN ISO 15874-2:2013

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)

Superseded date

04-01-2020

Published date

20-02-2013

Sorry this product is not available in your region.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics
8 Physical and chemical characteristics
9 Performance requirements
10 Marking
Annex A (informative) - Derivation of S[calc,max]
Bibliography

ISO 15874-2:2013 specifies the requirements of pipes made from polypropylene (PP) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems under operating pressures and temperatures appropriate to the class of application.It covers a range of service conditions (application classes), design pressures and pipe dimension classes.It also specifies test parameters for test methods.In conjunction with the other parts of ISO 15874, ISO 15874-2:2013 is applicable to PP pipes, their joints and to joints with components of PP, other plastics and non-plastics materials intended to be used for hot and cold water installations.It is applicable to pipes with or without (a) barrier layer(s).

Committee
CEN/TC 155
DevelopmentNote
Supersedes PREN ISO 15874-2. (03/2013)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
Supersedes

DIN EN 1254-6:2012-12 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
11/30197617 DC : 0 BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION
PREN 1254-6 : DRAFT 2011 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS
EN ISO/TS 15874-7 : 2003 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
NF EN 1264-4 : 2010 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
I.S. EN 1264-4:2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
DIN EN ISO 15874-1:2004-03 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP)
DIN EN ISO 15874-5:2004-03 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
DIN EN ISO 15874-3:2004-03 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS
11/30239909 DC : 0 BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
09/30202316 DC : 0 BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES
11/30213587 DC : 0 BS EN 1254-6 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
07/19990369 DC : 0 BS EN 806-4 - SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4 - INSTALLATION
EN 1264-4:2009 Water based surface embedded heating and cooling systems - Part 4: Installation
PREN 15015 : DRAFT 2014 PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
ISO/TS 15874-7:2003 Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
DIN EN 1264-4:2009-11 Water based surface embedded heating and cooling systems - Part 4: Installation
BS EN 1264-4:2009 Water based surface embedded heating and cooling systems Installation
UNI EN 15015 : 2008 PLASTICS PIPING SYSTEMS - SYSTEMS FOR HOT AND COLD WATER NOT INTENDED FOR HUMAN CONSUMPTION - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS
UNI EN 1254-6 : 2012 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
DD CEN ISO/TS 15874-7:2003 Plastics piping systems for hot and cold water installations. Polypropylene (PP) Guidance for the assessment of conformity
UNI EN 1264-4 : 2009 WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
I.S. EN 1254-6:2012 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTINGS WITH PUSH-FIT ENDS
14/30297462 DC : 0 BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
BS EN 806-2:2005 Specifications for installations inside buildings conveying water for human consumption Design
EN 806-2:2005 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
BS EN 1254-6:2012 Copper and copper alloys. Plumbing fittings Fittings with push-fit ends
I.S. EN ISO/TS 15874-7:2004 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY
EN 1254-6:2012 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
UNE-EN 1254-6:2013 Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends
07/30168416 DC : 0 BS EN 1264-4 - WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION
UNI EN 806-2 : 2008 SPECIFICATION FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 2: DESIGN
DIN EN 806-2:2005-06 Specification for installations inside buildings conveying water for human consumption - Part 2: Design
UNE-EN 1264-4:2010 Water based surface embedded heating and cooling systems - Part 4: Installation

ISO 15874-3:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings
ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 15874-1:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
ISO 9080:2012 Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
ISO 9854-1:1994 Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 1: General test method
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
CEN/TR 12108:2012 Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
ISO 9854-2:1994 Thermoplastics pipes for the transport of fluids — Determination of pendulum impact strength by the Charpy method — Part 2: Test conditions for pipes of various materials
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
ISO 13760:1998 Plastics pipes for the conveyance of fluids under pressure — Miner's rule — Calculation method for cumulative damage
ISO 15874-5:2013 Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system
ISO/TS 15874-7:2003 Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
ISO 7686:2005 Plastics pipes and fittings — Determination of opacity
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.