I.S. EN 12733:2001
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
AGRICULTURAL AND FORESTRY MACHINERY - PEDESTRIAN CONTROLLED MOTOR MOWERS - SAFETY
Hardcopy , PDF
31-01-2020
English
01-01-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 General
5.2 Engine starting and stopping devices
5.3 Manual controls
5.4 Marking of controls
5.5 Controls of movements of the machine and of the
blade(s)
5.6 Reverse gear
5.7 Handlebars
5.8 Pressurized components
5.9 Liquid spillage
5.10 Exhaust system
5.11 Steering mechanism
5.12 Brakes
5.13 Electrical installations
5.14 Noise
5.15 Vibration
6 Specific requirements
6.1 Sickle bar mowers
6.2 Grassland mowers
6.3 Flail mowers
6.4 Scrub clearing machines
7 Information for use
7.1 Instruction handbook
7.2 Marking
Annex A (normative) List of hazards
Annex B (normative) Noise test code for motor mowers -
Engineering methods (grade 2)
B.0 Scope
B.1 A-weighted sound power level determination
B.2 A-weighted emission sound pressure level determination
B.3 Requirement for test floor
B.4 Installation, mounting and operating conditions
B.5 Measurement uncertainties and declaration of noise
emission values
B.6 Information to be recorded and reported
Annex C (normative) Vibration measurement of motor mowers
C.1 Quantities to be measured
C.2 Instrumentation
C.3 Measurement direction and measurement location
C.4 Test procedure
C.5 Measurement procedure
C.6 Determination of the measurement result
Annex D (normative) Foot probe test
D.1 Test equipment
D.2 Test method
D.3 Test acceptance
Annex E (normative) Material of protective skirts
E.1 Tearing resistance test
E.2 Perforation resistance test
E.3 Wear resistance test
Annex F (normative) Corrugated fibreboard penetration tests
on grassland mowers - Test enclosure wall
panels
F.1 Purpose
F.2 Test Fixture
F.3 Fibreboard samples
F.4 Procedure
F.5 Acceptance criteria
Annex G (normative) Target elevation areas
G.1 Lower elevation target
G.2 Middle elevation target
G.3 Top elevation target
G.4 Operator target area
Annex H (normative) Test enclosure
H.1 Base
H.2 Target composition
Annex I (normative) Thrown object test for flail mower
I.1 Principle
I.2 Test installation
I.3 Test procedure
I.4 Test result
I.5 Acceptance criteria
Annex J (normative) Thrown object test for scrub clearing
machines
J.1 Test equipment
J.2 Test method
J.3 Data sheet - Thrown object test for scrub clearing machine
Annex K (informative) Example of a material and construction
fulfilling the requirements for an
artificial surface
K.1 Material
K.2 Construction
Annex L (informative) Examples of machines
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC, amended by Directive 98/79/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Provides safety requirements and their verification for design and construction of pedestrian controlled motor mowers.
| DevelopmentNote |
2001 Edition Re-Issued in April 2009 & incorporates AMD 1 2009. (05/2009)
|
| DocumentType |
Standard
|
| Pages |
76
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| SN EN 12733 : 2001 + A1 2009 | Identical |
| BS EN 12733 : 2001 | Identical |
| NS EN 12733 : 2001 + A1 2009 | Identical |
| DIN EN 12733:2016-08 (Draft) | Identical |
| NEN EN 12733 : 2001 + A1 2009 | Identical |
| UNI EN 12733 : 2009 | Identical |
| EN 12733:2001+A1:2009 | Identical |
| NF EN 12733 : 2001 + A1 2009 | Identical |
| ONORM EN 12733 : 2011 | Identical |
| NBN EN 12733 : 2001 + A1 2009 | Identical |
| UNE-EN 12733:2002 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 3789-1:1982 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Location and method of operation of operator controls — Part 1: Common controls |
| EN 836:1997+A4:2011 | Garden equipment - Powered lawnmowers - Safety |
| ISO 3767-3:2016 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 3: Symbols for powered lawn and garden equipment |
| EN 1033 : 1995 | HAND-ARM VIBRATION - LABORATORY MEASUREMENT OF VIBRATION AT THE GRIP SURFACE OF HAND-GUIDED MACHINERY - GENERAL |
| ISO 5718-2:1991 | Harvesting equipment Flat blades for rotary mowers Part 2: Specifications for type B flat blades |
| ISO 11102-1:1997 | Reciprocating internal combustion engines Handle starting equipment Part 1: Safety requirements and tests |
| ISO 2758:2014 | Paper Determination of bursting strength |
| EN ISO 11820:1996 | Acoustics - Measurements on silencers in situ (ISO 11820:1996) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| EN 60804:2000 | Integrating-averaging sound level meters |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| EN 563:1994/A1:1999/AC:2000 | SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN ISO 354:2003 | Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
| ISO 3767-1:2016 | Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 1: Common symbols |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN ISO 11806:2008 | Agricultural and forestry machinery - Portable hand-held combustion engine driven brush cutters and grass trimmers - Safety (ISO 11806:1997) |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN 60651:1994/A2:2001 | SOUND LEVEL METERS (IEC 60651:1979/A2:2000) |
| EN ISO 11691:2009 | Acoustics - Measurement of insertion loss of ducted silencers without flow - Laboratory survey method (ISO 11691:1995) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN 745:1999+A1:2009 | Agricultural machinery - Rotary mowers and flail-mowers - Safety |
| ISO 5718-1:1989 | Harvesting equipment — Flat blades for rotary mowers — Specifications — Part 1: Type A flat blades |
| ISO 11102-2:1997 | Reciprocating internal combustion engines Handle starting equipment Part 2: Method of testing the angle of disengagement |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.