I.S. EN 12864:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LOW-PRESSURE, NON-ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
Hardcopy , PDF
27-06-2013
English
01-01-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
1 Scope
2 Normative references
3 Terms and definitions
3.1 General definitions
3.2 Definitions concerning gas
3.3 Definitions concerning pressures
3.4 Definitions concerning rates
4 Terminology
5 Structural characteristics
5.1 General
5.2 Materials
5.3 Special requirements
5.4 Mechanical strength
5.5 Soundness
5.6 Mechanical endurance
5.7 Resistance to humidity changes
5.8 Resistance to corrosion
6 Performance characteristics
7 Test methods
7.1 General conditions
7.2 Verification of structural characteristics
7.3 Verification of performance characteristics
8 Marking - Packaging - Instructions
8.1 General
8.2 Marking of the regulator
8.3 Packaging
8.4 Instructions for use and maintenance
Annex A (normative) Special requirements for regulators
fitted with pressure or rate operated safety
devices
A.1 Regulators fitted with an overpressure relief
valve of a limited flow rate
A.2 Regulators fitted with an overpressure shut off
device
A.3 Regulators fitted with an underpressure shut off
safety device
A.4 Regulators fitted with an excess flow valve
Annex B (normative) Special requirements for regulators
fitted with a temperature operated safety device
B.1 Definition
B.2 Structural characteristics
B.3 Performance characteristics
B.4 Test methods
Annex C (normative) Special requirements for low pressure
regulators under extreme temperature conditions
Annex D (normative) Multimode connection regulator for
LPG cylinders to supply appliances installed in
caravans and motor caravans or freshwater boats
D.1 Scope
D.2 Design characteristics
D.3 Structural characteristics
D.4 Operating characteristics
D.5 Marking - Packaging - Instructions
Annex E (normative) Complementary test requirements for
non metallic thermoplastic or thermosetting
materials used in the construction of regulators
E.1 Scope
E.2 Materials
E.3 Special conditions for carrying out the test
mentioned in the body of the standard
E.4 Special requirements
Annex F (normative) Supplementary requirements for reinforced
diaphragms and elastomeric seals used in LPG
appliances and their associated equipment
Annex G (normative) Inlet connections
Annex H (normative) Outlet connections
Annex I (normative) Special requirements for low pressure
non adjustable regulators fitted with two or three
outlets for outdoor use
I.1 Constructional characteristics
I.2 Performance characteristics
I.3 Test methods
I.4 Marking
Annex J (normative) Method for measuring leaks at test
pressures less than or equal to 20 bar
J.1 Scope
J.2 Diagram of the test bench
J.3 Determination of coefficient K
J.5 Checks
Annex K (normative) Special requirements for regulators
fitted with an inlet valve
K.1 Definition
K.2 Structural characteristics
K.3 Performance characteristics: mechanical strength
K.4 Test method
Annex L (informative) Alternative test method for
resistance to corrosion
L.1 Principle
L.2 Reagents
L.3 Apparatus
L.4 Test method
L.5 Results
Annex M (normative) Regulator for LPG cylinders to supply
appliances installed in seawater boats
M.1 Scope
M.2 General
M.3 Maximum guaranteed rate
M.4 Regulators fitted with a pressure relief valve
M.5 Vent
M.6 Connections
M.7 Material
M.8 Corrosion
M.9 Marking
M.10 Instructions for use and maintenance
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements or other
provisions of EU directives
States the structural and operational characteristics, the safety requirements and test methods, the marking, of low-pressure, non adjustable regulators for butane, propane or their mixtures, referred to in the body of the text as 'regulators'.
| DevelopmentNote |
Supersedes I.S. 208 (01/2003)
|
| DocumentType |
Standard
|
| Pages |
189
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 12864:2006-03 | Identical |
| SN EN 12864 : 2001 AMD 3 2010 | Identical |
| UNI EN 12864 : 2010 | Identical |
| NS EN 12864 : 2001 AMD 3 2009 | Identical |
| BS EN 12864 : 2001 | Identical |
| UNE-EN 12864:2002 | Identical |
| NF EN 12864 : 2002 AMD 3 2009 | Identical |
| NBN EN 12864 : 2002 AMD 3 2009 | Identical |
| NEN EN 12864 : 2002 AMD 3 2009 | Identical |
| DIN EN 12864 E : 2006 AMD 3 2010 | Identical |
| ISO 426-1:1983 | Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 1: Non-leaded and special copper-zinc alloys |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| ISO 75:1987 | Plastics and ebonite Determination of temperature of deflection under load |
| ISO 426-2:1983 | Wrought copper-zinc alloys — Chemical composition and forms of wrought products — Part 2: Leaded copper-zinc alloys |
| ISO 565:1990 | Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings |
| EN 561:2002 | Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes |
| EN ISO 7253 : 2001 | PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO NEUTRAL SALT SPRAY (FOG) |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| ISO 7253:1996 | Paints and varnishes — Determination of resistance to neutral salt spray (fog) |
| EN ISO 4628-3:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.