I.S. EN 13322-1:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL
Hardcopy , PDF
23-05-2024
English
01-01-2003
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Materials and heat treatment
5 Design
6 Construction and workmanship
7 New design tests
8 Batch tests
9 Tests on every cylinder
10 Failure to meet test requirements
11 Records
12 Marking
Annex A (normative) Cylinders made from longitudinal seam
high frequency induction (HFI) welded tube by
spinning of the end
Annex B (normative) Radiographic examination of welds
Annex C (normative) Description, evaluation of manufacturing
defects and conditions for rejection of welded steel
gas cylinders at time of visual inspection
Annex D (informative) Examples of design and batch test
certificates
Annex E (informative) Guidance on the application of conformity
assessment modules when using this standard
Bibliography
Defines minimum requirements concerning material, design, construction and workmanship, manufacturing processes and testing of refillable transportable welded carbon steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied and dissolved gases.
| DocumentType |
Standard
|
| Pages |
55
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 13322-1 : 2003 AMD 1 2006 | Identical |
| NEN EN 13322-1 : 2003 AMD 1 2006 | Identical |
| DIN EN 13322-1:2006-05 | Identical |
| SN EN 13322-1 : 2003 AMD 1 2006 | Identical |
| UNE-EN 13322-1:2003 | Identical |
| BS EN 13322-1 : 2003 | Identical |
| NS EN 13322-1 : 1ED 2003 | Identical |
| NBN EN 13322-1 : 2003 AMD 1 2006 | Identical |
| UNI EN 13322-1 : 2006 | Identical |
| ONORM EN 13322-1 : 2006 | Identical |
| EN 10208-2:2009 | Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirement class B |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10120:2017 | Steel sheet and strip for welded gas cylinders |
| EN 629-2 : 1996 | TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION |
| ISO 11114-1:2012 | Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| EN 288-1:1992/A1:1997 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES FOR FUSION WELDING |
| EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
| EN 288-3:1992/A1:1997 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 3: WELDING PROCEDURE TESTS FOR THE ARC WELDING OF STEELS |
| EN 1964-1:1999/AC:1999 | TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS STEEL GAS CYLINDERS OF WATER CAPACITIES FROM 0.5 LITRE UP TO AND INCLUDING 150 LITRES - PART 1: CYLINDERS MADE OF SEAMLESS STEEL WITH AN RM VALUE OF LESS THAN 1100 MPA |
| EN 1089-1 : 1996 | TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - STAMPMARKING |
| EN 12517:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - RADIOGRAPHIC TESTING OF WELDED JOINTS - ACCEPTANCE LEVELS |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN 10028-5:2017 | Flat products made of steels for pressure purposes - Part 5: Weldable fine grain steels, thermomechanically rolled |
| EN 1442:2017 | LPG equipment and accessories - Transportable refillable welded steel cylinders for LPG - Design and construction |
| EN 1800:2006 | Transportable gas cylinders - Acetylene cylinders - Basic requirements, definitions and type testing |
| EN 962:1996/A2:2000 | TRANSPORTABLE GAS CYLINDERS - VALVE PROTECTION CAPS AND VALVE GUARDS FOR INDUSTRIAL AND MEDICAL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTS |
| ISO 2504:1973 | Radiography of welds and viewing conditions for films Utilization of recommended patterns of image quality indicators (I.Q.I.) |
| EN 10083-1:2006 | Steels for quenching and tempering - Part 1: General technical delivery conditions |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| EN 25817 : 1992 | ARC WELDED JOINTS IN STEEL - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS |
| EN 629-1 : 1996 | TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - PART 1: SPECIFICATION |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.