Skip to content
Please enter a keyword to search
  • Preview

    I.S. EN 14506:2005

    Current The latest, up-to-date edition.

    DEVICES TO PREVENT POLLUTION BY BACKFLOW OF POTABLE WATER - AUTOMATIC DIVERTER - FAMILY H, TYPE C

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2005

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Nominal size and pressure ranges
    5 Designation
    6 Marking and technical documents
    7 Symbolization
    8 General design characteristics
    9 Physico-chemical characteristics
    10 Characteristics and tests
    11 Acoustic characteristics
    Annex A (normative) Sampling and test sequence

    Abstract - (Show below) - (Hide below)

    Defines the characteristics of automatic diverters suitable for use in drinking water systems at pressures up to 1 MPa (10 bar) and temperatures up to 65 Degree C and for 1 h at 90 Degree C.

    General Product Information - (Show below) - (Hide below)

    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 3822-1:1999 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
    EN 817:2008 Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications
    EN 806-1:2000/A1:2001 SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 1: GENERAL
    EN 1287:2017 Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification
    EN 1112:2008 Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
    EN 1113:2015 SANITARY TAPWARE - SHOWER HOSES FOR SANITARY TAPWARE FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
    EN 1286:1999 Sanitary tapware - Low pressure mechanical mixing valves - General technical specification
    EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
    EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    ISO 3822-2:1995 Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 2: Mounting and operating conditions for draw-off taps and mixing valves
    ISO 6509:1981 Corrosion of metals and alloys Determination of dezincification resistance of brass
    ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
    EN 200:2008 Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
    EN ISO 3822-1:1999/A1:2008 ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
    EN ISO 3822-2:1995 Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves (ISO 3822-2:1995)
    EN ISO 6509 : 1995 CORROSION OF METALS AND ALLOYS - DETERMINATION OF DEZINCIFICATION RESISTANCE OF BRASS
    EN 1111:2017 Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    EN 248:2002 Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective