I.S. EN 1501-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REFUSE COLLECTION VEHICLES AND THEIR ASSOCIATED LIFTING DEVICES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 3: FRONT LOADED REFUSE COLLECTION VEHICLES
Hardcopy , PDF
29-04-2021
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Modes and controls of front loaded RCV
5 List of significant hazards
6 Safety requirements
7 Verification
8 Information for use
Annex A (normative) - Definition of working and functional
spaces
Annex B (normative) - Examples of data sheet
Annex C (informative) - Types of systems for front loaded
RCVs: lifting devices, compaction
and discharge systems and types of
waste containers
Annex D (normative) - Warning signals
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements
of EU Directive 98/37/EC, amended by
98/79/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements
of EU Directive 2006/42/EC
Bibliography
Applicable to front loaded refuse collection vehicles, as defined in 3.2, and specifies their technical requirements.
| DocumentType |
Standard
|
| Pages |
65
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 1501-3:2008 | Identical |
| EN 13071 : 2002 | SELECTIVE WASTE COLLECTION CONTAINERS - ABOVE-GROUND MECHANICALLY-LIFTED CONTAINERS WITH CAPACITIES FROM 80 L TO 5000 L FOR SELECTIVE COLLECTION OF WASTE |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| CEN Guide 414:2017 | Safety of machinery - Rules for the drafting and presentation of safety standards |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 1032:2003+A1:2008 | Mechanical vibration - Testing of mobile machinery in order to determine the vibration emission value |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 12574-1:2017 | Stationary waste containers - Part 1: Containers with a capacity up to 10 000 l with flat or dome lid(s), for trunnion, double trunnion or pocket lifting device - Dimensions and design |
| EN 840-4:2012 | Mobile waste and recycling containers - Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices - Dimensions and design |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN 840-3:2012 | Mobile waste and recycling containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design |
| EN 1501-4:2007 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles |
| ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
| EN 12574-3:2017 | Stationary waste containers - Part 3: Safety and health requirements |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 13478:2001+A1:2008 | Safety of machinery - Fire prevention and protection |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN ISO 7731:2008 | Ergonomics - Danger signals for public and work areas - Auditory danger signals (ISO 7731:2003) |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| ISO 7731:2003 | Ergonomics Danger signals for public and work areas Auditory danger signals |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 12574-2:2017 | Stationary waste containers - Part 2: Performance requirements and test methods |
| EN 840-1:2012 | Mobile waste and recycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
| EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 840-2:2012 | Mobile waste and recycling containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.